Crystal Growth of Ca₃Nb(Ga1-xAlx)₃Si₂O14 Piezoelectric Single Crystals with Various Al Concentrations.
Ontology highlight
ABSTRACT:
SUBMITTER: Yokota Y
PROVIDER: S-EPMC5512616 | biostudies-other | 2015 Aug
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Melting metallurgy is still the most frequently used and simplest method for the processing of metallic materials. Some of the materials (especially intermetallics) are very difficult to prepare by this method due to the high melting points, poor fluidity, or formation of cracks and pores after casting. This article describes the processing of Ti-Al-Si alloys by arc melting, and shows the microstructure, phase composition, hardness, fracture toughness, and compression tests of these alloys. These results are compared with the same alloys prepared by powder metallurgy by the means of a combination of mechanical alloying and spark plasma sintering. Ti-Al-Si alloys processed by melting metallurgy are characterized by a very coarse structure with central porosity. The phase composition is formed by titanium aluminides and titanium silicides, which are full of cracks. Ti-Al-Si alloys processed by the powder metallurgy route have a relatively homogeneous fine-grained structure with higher hardness. However, these alloys are very brittle. On the other hand, the fracture toughness of arc-melted samples is immeasurable using Palmqvist's method because the crack is stopped by a large area of titanium aluminide matrix.
| S-EPMC6803991 | biostudies-literature
Project description:Sulfasalazine is used as an anti-inflammatory drug to treat large intestine diseases and atrophic arthritis. In the solid state, two tautomers are known: an amide tautomer (triclinic polymorph) and an imide tautomer (monoclinic polymorph). Crystallization of six new multicomponent solids of sulfasalazine with three cocrystal formers and three salt formers has been achieved by slurry, liquid-assisted grinding and slow evaporation methods. All of the solid forms are characterized by X-ray diffraction techniques, thermal analysis, and Fourier transform infrared spectroscopy. The crystal structural analysis reveals that two sulfasalazine molecules or anions arrange in a head-to-head fashion involving their pyridyl, amide, and sulfonyl groups in an R22(7):R22(8):R22(7) motif. This is the key structural unit appearing in both sulfasalazine imide polymorph and all six multicomponent crystals. In addition, sulfasalazine exists in the amide form in all unsolvated multicomponent crystals obtained in this work and adopts the imide tautomer in the solvated cocrystals and salt. Hirshfeld surface analysis and the associated two-dimensional (2D) fingerprint plots demonstrate that sulfasalazine has significant hydrogen bond donor capability when cocrystallized and is a significant hydrogen bond acceptor in the salts. The frontier molecular orbital analysis indicates that sulfasalazine cocrystals are chemically more stable than the salts.
| S-EPMC10401639 | biostudies-literature
Project description:The Nb-silicide-based alloy of near eutectic composition (at.%) Nb-21.1Si-8.3Ti-5.4Mo-4W-0.7Hf (alloy CM1) was studied in the cast and heat-treated (1500 °C/100 h) conditions. The alloy was produced in the form of buttons and bars using three different methods, namely arc-melting, arc-melting and suction casting, and optical floating zone (OFZ) melting. In the former two cases the alloy solidified in water-cooled copper crucibles. Buttons and suction-cast bars of different size, respectively of 10 g and 600 g weight and 6 mm and 8 mm diameter, were produced. The OFZ bars were grown at three different growth rates of 12, 60 and 150 mm/h. It was confirmed that the type of Nb₅Si₃ formed in the cast microstructures depended on the solidification conditions. The primary phase in the alloy CM1 was the βNb₅Si₃. The transformation of βNb₅Si₃ to αNb₅Si₃ had occurred in the as cast large size button and the OFZ bars grown at the three different growth rates, and after the heat treatment of the small size button and the suction-cast bars of the alloy. This transformation was accompanied by subgrain formation in Nb₅Si₃ and the precipitation of Nbss in the large size as cast button and only by the precipitation of Nbss in the cast OFZ bars. Subgrains and precipitation of Nbss in αNb₅Si₃ was observed in the small size button and suction-cast bars after the heat treatment. Subgrains formed in αNb₅Si₃ after the heat treatment of the OFZ bars. The partitioning of solutes and in particular of Mo and Ti was key to this phase transformation. Subgrain formation was not necessary for precipitation of Nbss in αNb₅Si₃, but the partitioning of solutes was essential for this precipitation.
| S-EPMC6024954 | biostudies-literature
Project description:We studied the effect of the addition of Hf, Sn, or Ta on the density, macrosegregation, microstructure, hardness and oxidation of three refractory metal intermetallic composites based on Nb (RM(Nb)ICs) that were also complex concentrated alloys (i.e., RM(Nb)ICs/RCCAs), namely, the alloys TT5, TT6, and TT7, which had the nominal compositions (at.%) Nb-24Ti-18Si-5Al-5B-5Cr-6Ta, Nb-24Ti-18Si-4Al-6B-5Cr-4Sn and Nb-24Ti-17Si-5Al-6B-5Cr-5Hf, respectively. The alloys were compared with B containing and B free RM(Nb)ICs. The macrosegregation of B, Ti, and Si was reduced with the addition, respectively of Hf, Sn or Ta, Sn or Ta, and Hf or Sn. All three alloys had densities less than 7 g/cm3. The alloy TT6 had the highest specific strength in the as cast and heat-treated conditions, which was also higher than that of RCCAs and refractory metal high entropy alloys (RHEAs). The bcc solid solution Nbss and the tetragonal T2 and hexagonal D88 silicides were stable in the alloys TT5 and TT7, whereas in TT6 the stable phases were the A15-Nb3Sn and the T2 and D88 silicides. All three alloys did not pest at 800 °C, where only the scale that was formed on TT5 spalled off. At 1200 °C, the scale of TT5 spalled off, but not the scales of TT6 and TT7. Compared with the B free alloys, the synergy of B with Ta was the least effective regarding oxidation at 800 and 1200 °C. Macrosegregation of solutes, the chemical composition of phases, the hardness of the Nbss and the alloys, and the oxidation of the alloys at 800 and 1200 °C were considered from the perspective of the Niobium Intermetallic Composite Elaboration (NICE) alloy design methodology. Relationships between properties and the parameters VEC, δ, and Δχ of alloy or phase and between parameters were discussed. The trends of parameters and the location of alloys and phases in parameter maps were in agreement with NICE.
| S-EPMC8715753 | biostudies-literature
Project description:Single crystals of the title compound, aluminium niobium triphosphate, Al(0.5)Nb(1.5)(PO(4))(3), have been synthesized by a high-temperature reaction in a platinium crucible. The Al(III) and Nb(V) atoms occupy the same site on the axis, with disorder in the ratio of 1:3. The fundamental building units of the title structure are isolated Al/NbO(6) octa-hedra and PO(4) tetra-hedra (. 2 symmetry), which are further inter-locked by corner-sharing O atoms, leading to a three-dimensional framework structure with infinite channels along the a axis.
| S-EPMC3051931 | biostudies-literature
Project description:Coating system(s) will be required for Nb-silicide based alloys. Alumina forming alloys that are chemically compatible with the Nb-silicide based alloy substrate could be components of such systems. The intermetallic alloys Nb1.45Si2.7Ti2.25Al3.25Hf0.35 (MG5) and Nb1.35Si2.3Ti2.3Al3.7Hf0.35 (MG6) were studied in the cast, heat treated and isothermally oxidised conditions at 800 and 1200 °C to find out if they are αAl₂O₃ scale formers. A (Al/Si)alloy versus Nb/(Ti + Hf)alloy map, which can be considered to be a map for Multi-Principle Element or Complex Concentrated Nb-Ti-Si-Al-Hf alloys, and a [Nb/(Ti + Hf)]Nb5Si3 versus [Nb/(Ti + Hf)]alloy map were constructed making use of the alloy design methodology NICE and data from a previously studied alloy, and were used to select the alloys MG5 and MG6 that were expected (i) not to pest, (ii) to form αAl₂O₃ scale at 1200 °C, (iii) to have no solid solution, (iv) to form only hexagonal Nb₅Si₃ and (v) to have microstructures consisting of hexagonal Nb₅Si₃, Ti₅Si₃, Ti₅Si₄, TiSi silicides, and tri-aluminides and Al rich TiAl. Both alloys met the requirements (i) to (v). The alumina scale was able to self-heal at 1200 °C. Liquation in the alloy MG6 at 1200 °C was linked with the formation of a eutectic like structure and the TiAl aluminide in the cast alloy. Key to the oxidation of the alloys was the formation (i) of "composite" silicide grains in which the Nb₅Si₃ core was surrounded by the Ti₅Si₄ and TiSi silicides, and (ii) of tri-aluminides with high Al/Si ratio, particularly at 1200 °C and very low Nb/Ti ratio forming in-between the "composite" silicide grains. Both alloys met the "standard definition" of high entropy alloys (HEAs). Compared with HEAs with bcc solid solution and intermetallics, the VEC values of both the alloys were outside the range of reported values. The parameters VEC, and of Nb-Ti-Si-Al-Hf coating alloys and non-pesting Nb-silicide based alloys were compared and trends were established. Selection of coating alloys with possible "layered" structures was discussed and alloy compositions were proposed.
| S-EPMC6427440 | biostudies-literature
Project description:This paper presents a simple and optimized metal organic chemical vapor deposition (MOCVD) protocol for the deposition of perovskite BiFeO3 films on silicon-based substrates, in order to move toward the next generation of lead-free hybrid energy harvesters. A bi-metal mixture that is composed of Bi(phenyl)3, and Fe(tmhd)3 has been used as a precursor source. BiFeO3 films have been grown by MOCVD on IrO2/Si substrates, in which the conductive IrO2 functions as a bottom electrode and a buffer layer. BiFeO3 films have been analyzed by X-ray diffraction (XRD) for structural characterization and by field-emission scanning electron microscopy (FE-SEM) coupled with energy dispersive X-ray (EDX) analysis for the morphological and chemical characterizations, respectively. These studies have shown that the deposited films are polycrystalline, pure BiFeO3 phase highly homogenous in morphology and composition all over the entire substrate surface. Piezoelectric force microscopy (PFM) and Piezoelectric Force Spectroscopy (PFS) checked the piezoelectric and ferroelectric properties of the film.
| S-EPMC7221529 | biostudies-literature
Project description:Dealkalization is the necessary step for the multipurpose use of red mud (RM), and acid leaching is a productive method to realize the dealkalization of RM. Most researches focus on recovering metals from the highly alkaline waste by pure acid leaching or stabilization by dealkalization. In this study, according to the strong alkalinity of RM and strong acidity of the waste acid from titanium dioxide production, the waste acid was used for the dealkalization of RM. The effects of leaching temperature, reaction time, the concentration of waste acid, liquid-solid ratio (L/S), and stirring rate on the dealkalization of RM were investigated, and the main metal ions in the dealkalization solution were analyzed. The results show that the leaching ratio of sodium can reach 92.3591% when the leaching temperature is 30 °C, the reaction time is 10 min, the concentration of waste acid is 0.6238 mol/L, the L/S is 4:1, and the stirring rate is 300 rpm. The residual alkali content in the treated RM is 0.2674%, which is a reduction to less than 1%. The phase analysis results show that the sodalite and cancrinite in RM are dissolved, decomposed, and transformed after acid leaching. Therefore, RM meets the requirements of building materials after dealkalization, which provides further development as building material products.
| S-EPMC8655946 | biostudies-literature
Project description:The heterogeneous nucleation of primary Si and eutectic Si can be attributed to the presence of AlP. Although P, in the form of AlP particles, is usually observed in the centre of primary Si, there is still a lack of detailed investigations on the distribution of P within primary Si and eutectic Si in hypereutectic Al-Si alloys at the atomic scale. Here, we report an atomic-scale experimental investigation on the distribution of P in hypereutectic Al-Si alloys. P, in the form of AlP particles, was observed in the centre of primary Si. However, no significant amount of P was detected within primary Si, eutectic Si and the Al matrix. Instead, P was observed at the interface between the Al matrix and eutectic Si, strongly indicating that P, in the form of AlP particles (or AlP 'patch' dependent on the P concentration), may have nucleated on the surface of the Al matrix and thereby enhanced the heterogeneous nucleation of eutectic Si. The present investigation reveals some novel insights into heterogeneous nucleation of primary Si and eutectic Si by AlP in hypereutectic Al-Si alloys and can be used to further develop heterogeneous nucleation mechanisms based on adsorption.
| S-EPMC4848514 | biostudies-literature
Project description:In this research, various processing conditions were implemented to enhance the mechanical properties of Al-Si alloys. The silicon content was varied from hypoeutectic (Si-10 wt.%) to eutectic (Si-12.6 wt.%) and hypereutectic (Si-14 wt.%) for the preparation of Al-XSi-3Cu-0.5Fe-0.6 Mg (X = 10?14%) alloys using die casting. Subsequently, these alloys were hot-extruded with an optimum extrusion ratio (17:1) at 400 °C to match the output extruded bar to the compressor size. An analysis of the microstructural features along with a chemical compositional analysis were carried out using scanning electron microscope along with energy dispersive X-ray spectroscopy and transmission electron microscope. The SEM micrographs of the extruded samples displayed cracks in primary Si, and the intermetallic (?-Al?FeSi) phase was fragmented accordingly. In addition, the silicon phase was homogenously distributed, and the size remained constant. The mechanical properties of the extruded samples were enhanced by the increase of silicon content, and consequently the ductility decreased. By implementing proper T6 heat treatment parameters, coherent Al?Cu phases were formed in the Al matrix, and the Si phase was gradually increased along with the silicon content. Therefore, high tensile strength was achieved, reaching values for the Al-XSi-3Cu-0.5Fe-0.6Mg (X = 10?14%) alloys of 366 MPa, 388 MPa, and 420 MPa, respectively.
| S-EPMC6266997 | biostudies-other