Solidified Floating Organic Drop Microextraction for the Detection of Trace Amount of Lead in Various Samples by Electrothermal Atomic Absorption Spectrometry.
Ontology highlight
ABSTRACT:
SUBMITTER: Aydın Urucu O
PROVIDER: S-EPMC5541831 | biostudies-other | 2017
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Benzene is one of the carcinogenic compounds in the work environments. Exposure assessment of benzene through biological monitoring is an acceptable way to accurately measure the real exposure in order to conducting the health risk assessment, but it is always complicated, laborious, time consuming and costly process. A new sensitive, simple, fast and environmental friendly method was developed for the determination of urinary metabolite of benzene, trans trans muconic acid (t,t-MA) by dispersive liquid-liquid micro extraction based on solidification of floating organic droplet coupled with high-performance liquid chromatography with ultra violet detector. Central composite design methodology was utilized to evaluate the effective factors on the extraction output of the target metabolite. The calibration curve was plotted in the concentration ranges of 0.02-5 µg mL-1. The precision and accuracy of the method were assayed via the relative standard deviation (RSD%) and relative recovery (RR%) using spiked samples with three replications. The RR% and RSD% of the optimized method were 86.9-91.3% and 4.3-6.3% respectively. The limit of detection (LOD) of the method was 0.006 µg mL-1. The level of t,t-MA in real samples was ranged from 0.54 to 1.64 mg/g creatinine. We demonstrated that t,t-MA can be extracted and determined by an inexpensive, simple and fast method.
| S-EPMC8333051 | biostudies-literature
Project description:In this work, a rapid detection method using solid sampling electrothermal vaporization atomic absorption spectrometry (SS-ETV-AAS) was established for cadmium in chocolate. The instrumental system includes a solid sampling ETV unit, a catalytic pyrolysis furnace, an AAS detector, and a gas supply system with only an air pump and a hydrogen generator. Herein, MgO material with 1.0-1.5 mm particle size was first employed to replace the kaolin filler previously used to further shorten the peak width and to thereby improve the sensitivity. With 350 mL/min of air, a chocolate sample was heated for 25 s from 435 to 464 °C to remove water and organic matrices; then, after supplying 240 mL/min hydrogen and turning down air to 120 mL/min, a N2/H2 mixture gas was formed to accelerate Cd vaporization from chocolate residue under 465 to 765 °C. Under the optimized conditions, the detection limit (LOD) was obviously lowered to 70 pg/g (vs. previous 150 pg/g) with R2 > 0.999; the relative standard deviations (RSD) of repeated measurements for real chocolate samples ranged from 1.5% to 6.4%, indicating a favorable precision; and the Cd recoveries were in the range of 93-107%, proving a satisfied accuracy. Thus, the total analysis time is less than 3 min without the sample digestion process. Thereafter, 78 chocolate samples with different brands from 9 producing countries in China market were collected and measured by this proposed method. Based on the measured Cd concentrations, a dietary exposure assessment was performed for Chinese residents, and the target hazard quotient (THQ) values are all less than 1, proving no significant health risk from intaking chocolate cadmium for Chinese residents.
| S-EPMC9572000 | biostudies-literature
Project description:A novel, simple, and reliable ultraperformance liquid chromatography tandem-mass spectrometry (UPLC-MS/MS ) assay based on dispersive liquid-liquid microextraction followed by ultrasound-assisted reverse extraction from solidified floating organic droplets was established for determination of multiclass pharmaceuticals in the water sample. Six commonly used drugs of various therapeutic classes: ibuprofen, ketorolac, lamotrigine, propranolol, pantoprazole, and losartan were extracted from water samples by using 50 μL 1-undecanol as extracting solvent and 400 μL acetonitrile as dispersive solvent. After collecting the floating organic droplets by cold centrifugation, an ultrasound-assisted back extraction procedure was performed to make the sample compatible for UPLC-MS/MS analysis. Acquity BEH C18 column (2.1 × 100; 1.7 μm) was used for separation of target analytes that were eluted by a gradient mobile phase composition of 15 mM ammonium acetate and acetonitrile at a flow rate of 0.25 mL/min. The sample ionization was performed by using electrospray ionization in positive mode, and multiple reaction monitoring was used for quantification of target analytes. After optimizing the assay conditions, all calibration curves were found to be linear with limit of detection and limit of quantification were ranged in between 0.06-0.15 and 0.16-0.41 ng/mL, respectively. The enrichment factor was found to be 172-192-fold and the relative recovery was ranged between 93.1 and 109.4% between target analytes. These satisfactory results confirmed that the proposed method is specific and reliable for application of trace analysis of target analytes in waste water samples.
| S-EPMC7992067 | biostudies-literature
Project description:This study reports minerals and trace elements quantification in raw caprine milk of Beetal breed, reared in Northern India and their feed, fodder & water using flame atomic absorption spectrophotometry and flame photometry. The mineral and trace elements' concentration in the milk was in the order: K > Ca > Na > Fe > Zn > Cu. The results showed that minerals concentration in caprine milk was lesser than reference values. But trace elements concentration (Fe and Zn) was higher than reference values. Multivariate statistical techniques, viz., Pearsons' correlation, Cluster analysis (CA) and Principal component analysis (PCA) were applied to analyze the interdependences within studied variables in caprine milk. Significantly positive correlations were observed between Fe - Zn, Zn - K, Ca - Na and Ca - pH. The results of correlation matrix were further supported by Cluster analysis and Principal component analysis as primary cluster pairs were found for Ca - pH, Ca - Na and Fe - Zn in the raw milk. No correlation was found between mineral & trace elements content of the milk and feed.
| S-EPMC4519456 | biostudies-literature
Project description:Simultaneous transmissivity and absorptivity measurements were carried out in the visible at a laser wavelength of 532 nm on drop-cast, carbon-black-laden filters under ambient (laboratory) conditions. The focus of this investigation was to establish the feasibility of this approach to estimate the mass absorption coefficient of the isolated particles and compare results to earlier work with the same carbon-black source. Transmissivity measurements were carried out with a laser probe beam positioned normal to the particle-laden filter surface. Absorptivity measurements were carried out using a laser-heating approach to record in time the sample temperature rise to steady-state and decay back to the ambient temperature. The sample temperature was recorded using a fine-wire thermocouple that was integrated into the transmission arrangement by placing the thermocouple flush with the filter back surface. The advantage of this approach is that the sample absorptivity can be determined directly (using laser heating) instead of resolving the difference between reflectivity (filter surface scattering) and transmissivity. The current approach also provides the filter optical characteristics, as well as an estimate of filter effects on the absorption coefficient due to particle absorption enhancement or shadowing. The approach may also be incorporated into other filter-based techniques, like the particle/soot absorption photometer, with the simple addition of a thermocouple to the commercial instrument. For this investigation, measurements were carried out with several blank uncoated quartz filters. A range of solution concentrations was prepared with a well-characterized carbon black in deionized water (i.e., a water-soluble carbonaceous material referred to as a surrogate black carbon or 'carbon black'). The solution was then drop cast using a calibrated syringe onto blank filters to vary particle loading. After evaporation of the water, the measurements were repeated with the coated filters. The measurement repeatability (95% confidence level) was better than 0.3 K for temperature and 3 × 10-5 mW for laser power. From the measurements with both the blank and coated filters, the absorption coefficient was determined for the isolated particles. The results were then compared with an earlier investigation by You et al. and Zangmeister and Radney, who used the same carbon-black material. The measurements were also compared with Lorenz-Mie computations for a polydispersion of spherical particles dispersed throughout a volume representative of the actual particles. The mass absorption coefficient for the polydispersion of carbon-black particles was estimated to be about 7.7 ± 1.4m2 g-1, which was consistent with the results expected for these carbon black particles.
| S-EPMC6774385 | biostudies-literature
Project description:The combination of an optical probe and single-drop direct immersion microextraction (DI-SDME-OP) was used for the preconcentration and subsequent spectrophotometric determination of rhodamine 6G (Rh6G). The developed method is based on the formation of an ionic associate between Rh6G and picric acid at pH 3.0 and its extraction with amyl acetate. A microdrop of the organic phase was stably placed in the hole of an optical probe immersed in the sample solution. The absorbance of the extraction phase was monitored at 534 nm. The proposed method combines in a single step several stages of the analytical procedure, such as pre-concentration, phase separation, transfer of the extraction phase to the instrument and online measurement. The sensitivity of the proposed approach is not inferior to existing microextraction methods involving the combination of liquid-phase or solid-phase extraction with spectrophotometry or HPLC with a UV-Vis detector. The evaluation of the greenness of the developed method carried out by the AGREE method (0.58 points) showed that it outperforms other similar existing techniques using this parameter. The calibration plot for the determination of Rh6G by the DI-SDME-OP method was linear over the range of 10-500 nM with a correlation coefficient of 0.9956. The limit of detection was 3.4 nM. The accuracy and applicability of the method were evaluated by the determination of Rh6G in natural waters and lipstick.
| S-EPMC11332950 | biostudies-literature
Project description:As a very attractive clean energy, hydrogen has a high energy density and great potential to achieve zero pollution emission. Therefore, the preparation of hydrogen evolution electrocatalysts with excellent performance is an urgent task to ameliorate the global energy shortage and environmental pollution. Here, a trace amount of NiP2 coupled with CoMoP nanosheets (NCMP) was synthesized by the one-step hydrothermal method and low-temperature phosphidation. Studies have found that although the dosage of NiP2 is very low, its appearance has been efficient to improve the hydrogen evolution reaction (HER) performance of CoMoP, which may be induced by the synergistic effect of the two different components NiP2 and CoMoP. To find the superior catalyst, the effect of Ni content on the catalyst performance is also studied, and it is found that when the dosage of Ni is 0.02 mM, NCMP-2 (2 means 0.02 mM) displays the most outstanding overpotential (10 mA cm-2) of 46 mV.
| S-EPMC8655887 | biostudies-literature
Project description:Two cheap, simple and reproducible methods for the electrophoretic determination of homocysteine thiolactone (HTL) in human urine have been developed and validated. The first method utilizes off-line single drop microextraction (SDME), whereas the second one uses off-line SDME in combination with field amplified sample injection (FASI). The off-line SDME protocol consists of the following steps: urine dilution with 0.2 mol/L, pH 8.2 phosphate buffer (1:2, v/v), chloroform addition, drop formation and extraction of HTL. The pre-concentration of HTL inside a separation capillary was performed by FASI. For sample separation, the 0.1 mol/L pH 4.75 phosphate buffer served as the background electrolyte, and HTL was detected at 240 nm. A standard fused-silica capillary (effective length 55.5 cm, 75 μm id) and a separation voltage of 21 kV (~99 μA) were used. Electrophoretic separation was completed within 7 min, whereas the LOD and LOQ for HTL were 0.04 and 0.1 μmol/L urine, respectively. The calibration curve in urine was linear in the range of 0.1-0.5 μmol/L, with R2 = 0.9991. The relative standard deviation of the points of the calibration curve varied from 2.4% to 14.9%. The intra- and inter-day precision and recovery were 6.4-10.2% (average 6.0% and 6.7%) and 94.9-102.7% (average 99.7% and 99.5%), respectively. The analytical procedure was successfully applied to the analysis of spiked urine samples obtained from apparently healthy volunteers.
| S-EPMC8468900 | biostudies-literature
Project description:Polarization and conductance losses are the fundamental dielectric attenuation mechanisms for graphene-based absorbers, but it is not fully understood in revealing the loss mechanism of affect graphene itself. For the first time, the reduced graphene oxide (RGO) based absorbers are developed with regulatory absorption properties and the absorption mechanism of RGO is mainly originated from the carrier injection behavior of trace metal Fe nanosheets on graphene. Accordingly, the minimum reflection loss (RLmin) of Fe/RGO-2 composite reaches - 53.38 dB (2.45 mm), and the effective absorption bandwidth achieves 7.52 GHz (2.62 mm) with lower filling loading of 2 wt%. Using off-axis electron hologram testing combined with simulation calculation and carrier transport property experiments, we demonstrate here the carrier injection behavior from Fe to graphene at the interface and the induced charge accumulation and rearrangement, resulting in the increased interfacial and dipole polarization and the conductance loss. This work has confirmed that regulating the dielectric property of graphene itself by adding trace metals can not only ensure good impedance matching, but also fully exploit the dielectric loss ability of graphene at low filler content, which opens up an efficient way for designing lightweight absorbers and may be extended to other types materials.
| S-EPMC10767016 | biostudies-literature
Project description:The solidification/stabilization (S/S) method is the usual technique for the remediation of soils polluted by heavy metal in recent years. However, freeze-thaw cycles, an important physical process producing weathering of materials, will affect the long-term stability of engineering characteristics in solidified contaminated soil. In addition, it is still questionable whether using large dosages of binders can enhance the engineering properties of solidified/stabilized contaminated soils. In this study, the three most commonly used binders (i.e., cement, quicklime, and fly ash), alone and mixed in different ratios, were thus added to lead-contaminated soil in various dosages, making a series of cured lead-contaminated soils with different dosages of binders. Afterward, unconfined compression strength tests, direct shear tests, and permeability tests were employed on the resulting samples to find the unconfined compressive strength (UCS), secant modulus ( E 50 ), internal friction angle ( ? ), cohesion ( c ), and permeability coefficient ( k ) of each solidified/stabilized lead-contaminated soil after 0, 3, 7, and 14 days of freeze-thaw cycles. This procedure was aimed at evaluating the influence of freeze-thaw cycle and binder dosage on engineering properties of solidified/stabilized lead-contaminated soils. Results of our experiments showed that cement/quicklime/fly ash could remediate lead-contaminated soils. However, it did not mean that the more the dosage of binder, the better the curing effect. There was a critical dosage. Excessive cementation of contaminated soils caused by too much binder would result in loss of strength and an increase in permeability. Furthermore, it was found that UCS, E 50 , ? , c , and k values generally decreased with the increase in freeze-thaw cycle time-a deterioration effect on the engineering characteristics of solidified lead-contaminated soils. Avoiding excessive cementation, 2.5% cement or quicklime was favorable for the value of E 50 while a 2.5% fly ash additive was beneficial for the k value. It is also suggested that if the freeze-thaw cycle continues beyond the period supported by excessive cementation, such a cycle will rapidly destroy the original structure of the soil and create large cracks, leading to an increase in permeability. The results also showed that the contaminated soils with a larger dosage of binders exhibited more significant deterioration during freeze-thaw cycles.
| S-EPMC7037547 | biostudies-literature