Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

The Influence of Lath, Block and Prior Austenite Grain (PAG) Size on the Tensile, Creep and Fatigue Properties of Novel Maraging Steel.

ABSTRACT: The influence of martensitic microstructure and prior austenite grain (PAG) size on the mechanical properties of novel maraging steel was studied. This was achieved by looking at two different martensitic structures with PAG sizes of approximately 40 µm and 80 µm, produced by hot rolling to different reductions. Two ageing heat-treatments were considered: both heat-treatments consisted of austenisation at 960 °C, then aging at 560 °C for 5 h, but while one was rapidly cooled the other was slow cooled and then extended aged at 480 °C for 64 h. It is shown that for the shorter ageing treatment the smaller PAG size resulted in significant improvements in strength (increase of more than 150 MPa), ductility (four times increase), creep life (almost four times increase in creep life) and fatigue life (almost doubled). Whereas, the extended aged sample showed similar changes in the fatigue life, elongation and hardness it displayed yet showed no difference in tensile strength and creep. These results display the complexity of microstructural contributions to mechanical properties in maraging steels.

SUBMITTER: Simm T

PROVIDER: S-EPMC5551773 | biostudies-other | 2017 Jun

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

Mechanical Properties, Short Time Creep, and Fatigue of an Austenitic Steel.

Project description:The correct choice of a material in the process of structural design is the most important task. This study deals with determining and analyzing the mechanical properties of the material, and the material resistance to short-time creep and fatigue. The material under consideration in this investigation is austenitic stainless steel X6CrNiTi18-10. The results presenting ultimate tensile strength and 0.2 offset yield strength at room and elevated temperatures are displayed in the form of engineering stress-strain diagrams. Besides, the creep behavior of the steel is presented in the form of creep curves. The material is consequently considered to be creep resistant at temperatures of 400 °C and 500 °C when subjected to a stress which is less than 0.9 of the yield strength at the mentioned temperatures. Even when the applied stress at a temperature of 600 °C is less than 0.5 of the yield strength, the steel may be considered as resistant to creep. Cyclic tensile fatigue tests were carried out at stress ratio R = 0.25 using a servo-pulser machine and the results were recorded. The analysis shows that the stress level of 434.33 MPa can be adopted as a fatigue limit. The impact energy was also determined and the fracture toughness assessed.

| S-EPMC5502991 | biostudies-other

Datasets acquired with correlative microscopy method for delineation of prior austenite grain boundaries and characterization of prior austenite grain size in a low-alloy high-performance steel.

Project description:Prior studies on martensitic steel microstructures have either delineated the prior austenite grain boundaries via chemical etching or reconstructed the prior austenite grains from crystallographic orientations measured with electron backscattered diffraction (EBSD). To appropriately validate the reconstruction algorithms, the EBSD data need to be collected on martensitic microstructures, where the prior austenite grain boundaries are delineated with techniques such as chemical etching that can serve as ground truth for comparison with the reconstructed prior austenite grains. In this article, the method of correlative microscopy is employed to collect scanning electron microscope (SEM) image and automated EBSD scan data from the same region of an appropriately etched steel specimen. The SEM images and automated EBSD scan data are presented for five different fields of view in the specimen. These datasets are analyzed and discussed in the accompanying article titled "Correlative microscopy for quantification of prior austenite grain size in AF9628 steel" [1].

| S-EPMC6806460 | biostudies-literature

Statistical data for the tensile properties and static fatigue of sic-based bundles.

Project description:Due to their high specific strength at elevated temperatures and resistance to oxidative environments, SiC-based fibers are of great interest for the reinforcement of ceramic matrix composites. They are however subjected to a slow crack growth (SCG) phenomenon causing their delayed failure under subcritical conditions. The testing of filaments, other than comprising handling difficulties, requires large sets of data (broadly dispersed), drawback alleviated by multifilament tow testing. The data available in the present paper correspond to a comprehensive mechanical characterization and static fatigue testing of various types of SiC-based fiber bundles. The initial non-linearity of load displacement curves were analyzed to reveal the tow structure originating from filament misalignment. Static fatigue tests were used to assess the lifetime prediction coefficients and its distribution parameters. These data may found interest for the interpretation of dispersion bundle testing can highlight under different solicitation mode. Such data are also prominent for the wealth of composite design and to guaranty long term performances over the broad application field offered.

| S-EPMC7452681 | biostudies-literature

Analysis of the Mechanical Behavior, Creep Resistance and Uniaxial Fatigue Strength of Martensitic Steel X46Cr13.

Project description:The article deals with the analysis of the mechanical behavior at different temperatures, uniaxial creep and uniaxial fatigue of martensitic steel X46Cr13 (1.4034, AISI 420). For the purpose of considering the aforementioned mechanical behavior, as well as determining the appropriate resistance to creep and fatigue strength levels, numerous uniaxial tests were carried out. Tests related to mechanical properties performed at different temperatures are presented in the form of engineering stress-strain diagrams. Short-time creep tests performed at different temperatures and different stress levels are presented in the form of creep curves. Fatigue tests carried out at stress ratios R = 0.25 and R = - 1 are shown in the form of S-N (fatigue) diagrams. The finite fatigue regime for each of the mentioned stress ratios is modeled by an inclined log line, while the infinite fatigue regime is modeled by a horizontal line, which represents the fatigue limit of the material and previously was calculated by the modified staircase method. Finally, the fracture toughness has been calculated based on the Charpy V-notch impact energy.

| S-EPMC5506967 | biostudies-other

Creep-Fatigue Failure Diagnosis.

Project description:Failure diagnosis invariably involves consideration of both associated material condition and the results of a mechanical analysis of prior operating history. This Review focuses on these aspects with particular reference to creep-fatigue failure diagnosis. Creep-fatigue cracking can be due to a spectrum of loading conditions ranging from pure cyclic to mainly steady loading with infrequent off-load transients. These require a range of mechanical analysis approaches, a number of which are reviewed. The microstructural information revealing material condition can vary with alloy class. In practice, the detail of the consequent cracking mechanism(s) can be camouflaged by oxidation at high temperatures, although the presence of oxide on fracture surfaces can be used to date events leading to failure. Routine laboratory specimen post-test examination is strongly recommended to characterise the detail of deformation and damage accumulation under known and well-controlled loading conditions to improve the effectiveness and efficiency of failure diagnosis.

| S-EPMC5458918 | biostudies-other

Corrosion behavior of metastable AISI 321 austenitic stainless steel: Investigating the effect of grain size and prior plastic deformation on its degradation pattern in saline media.

Project description:The role of grain size and strain rate on the corrosion behavior of plastically-deformed Ti-stabilized austenitic stainless steel (AISI 321) in saline media was investigated. The as-received coarse-grained alloy (CG: ~37 µm) was subjected to thermomechanical processing to develop fine (FG: ~3 µm) and ultrafine (UFG: ~0.24 µm) grained structures. These samples were deformed under high (dynamic) and low (quasi-static) strain-rate conditions to a similar true strain of ~0.86. Microstructural analyses on specimens after deformation prior to corrosion study suggests a shift from the estimated stacking fault energy value of the steel. Electrochemical tests confirm the highest corrosion resistance for UFG specimens due to the formation of the most stable adsorbed passive film. This is followed by FG and CG specimens in that order. For the three grain sizes, the corrosion resistance of specimen deformed under quasi-static loading condition is higher than that subjected to dynamic impact loading while the corrosion resistance of undeformed samples is the least. This work also confirms the non-detrimental effect of TiCs in AISI 321 austenitic stainless steel on its corrosion resistance. However, TiNs were observed to be detrimental by promoting pitting corrosion due to galvanic coupling of TiNs with their surrounding continuous phase. The mechanism of pitting in AISI 321 in chloride solution is proposed.

| S-EPMC6702197 | biostudies-literature

Effects of Grain Size on Ultrasonic Attenuation in Type 316L Stainless Steel.

Project description:A lead bismuth eutectic (LBE) spallation target will be installed in the Target Test Facility (TEF-T) in the Japan Proton Accelerator Research Complex (J-PARC). The spallation target vessel filled with LBE is made of type 316L stainless steel. However, various damages, such as erosion/corrosion damage and liquid metal embrittlement caused by contact with flowing LBE at high temperature, and irradiation hardening caused by protons and neutrons, may be inflicted on the target vessel, which will deteriorate the steel and might break the vessel. To monitor the target vessel for prevention of an accident, an ultrasonic technique has been proposed to establish off-line evaluation for estimating vessel material status during the target maintenance period. Basic R&D must be carried out to clarify the dependency of ultrasonic wave propagation behavior on material microstructures and obtain fundamental knowledge. As a first step, ultrasonic waves scattered by the grains of type 316L stainless steel are investigated using new experimental and numerical approaches in the present study. The results show that the grain size can be evaluated exactly and quantitatively by calculating the attenuation coefficient of the ultrasonic waves scattered by the grains. The results also show that the scattering regimes of ultrasonic waves depend heavily on the ratio of wavelength to average grain size, and are dominated by grains of extraordinarily large size along the wave propagation path.

| S-EPMC5551796 | biostudies-other

Kinetic Modeling of Grain Boundary Diffusion: The Influence of Grain Size and Surface Processes.

Project description:Based on rate equations, the kinetics of atom adsorption, desorption, and diffusion in polycrystalline materials is analyzed in order to understand the influence of grain boundaries and grain size. The boundary conditions of the proposed model correspond with the real situation in the electrolytes of solid oxide hydrogen fuel cells (SOFC). The role of the ratio of grain boundary and grain diffusion coefficients in perpendicular and parallel (to the surface) concentration profiles is investigated. In order to show the influence of absolute values of grain and grain boundary diffusion coefficients, we select four different cases in which one of the diffusion coefficients is kept constant while the others vary. The influence of grain size on diffusion processes is investigated using different geometrical models. The impact of kinetic processes taking place on the surface is analyzed by comparing results obtained assuming the first layer as a constant source and then involving in the model the processes of adsorption and desorption. It is shown that surface processes have a significant influence on the depth distribution of diffusing atoms and cannot be ignored. The analytical function of overall concentration dependence on grain and grain boundary volume ratio (Vg/Vgb) is found. The solution suggests that the concentration increases as a complementary error function while Vg/Vgb decreases.

| S-EPMC7084621 | biostudies-literature

Effects of Austenitizing Temperature on Tensile and Impact Properties of a Martensitic Stainless Steel Containing Metastable Retained Austenite.

Project description:Austenitizing temperature is one decisive factor for the mechanical properties of medium carbon martensitic stainless steels (MCMSSs). In the present work, the effects of austenitizing temperature (1000, 1020, 1040 and 1060 °C) on the microstructure and mechanical properties of MCMSSs containing metastable retained austenite (RA) were investigated by means of electron microscopy, X-ray diffraction (XRD), as well as tensile and impact toughness tests. Results suggest that the microstructure including an area fraction of undissolved M23C6, carbon and chromium content in matrix, prior austenite grain size (PAGS), fraction and composition of RA in studied MCMSSs varies with employed austenitizing temperature. By optimizing austenitizing temperature (1060 °C for 40 min) and tempering (250 °C for 30 min) heat treatments, the MCMSS demonstrates excellent mechanical properties with the ultimate tensile strength of 1740 ± 8 MPa, a yield strength of 1237 ± 19 MPa, total elongation (ductility) of 10.3 ± 0.7% and impact toughness of 94.6 ± 8.0 Jcm-2 at room temperature. The increased ductility of alloys is mainly attributed to the RA with a suitable stability via a transformation-induced plasticity (TRIP) effect, and a matrix containing reduced carbon and chromium content. However, the impact toughness of MCMSSs largely depends on M23C6 carbides.

| S-EPMC7924182 | biostudies-literature

Exceptional high fatigue strength in Cu-15at.%Al alloy with moderate grain size.

Project description:It is commonly proposed that the fatigue strength can be enhanced by increasing the tensile strength, but this conclusion needs to be reconsidered according to our study. Here a recrystallized α-Cu-15at.%Al alloy with moderate grain size of 0.62 μm was fabricated by cold rolling and annealing, and this alloy achieved exceptional high fatigue strength of 280 MPa at 10(7) cycles. This value is much higher than the fatigue strength of 200 MPa for the nano-crystalline counterpart (0.04 μm in grain size) despite its higher tensile strength. The remarkable improvement of fatigue strength should be mainly attributed to the microstructure optimization, which helps achieve the reduction of initial damage and the dispersion of accumulated damage. A new strategy of "damage reduction" was then proposed for fatigue strength improvement, to supplement the former strengthening principle. The methods and strategies summarized in this work offer a general pathway for further improvement of fatigue strength, in order to ensure the long-term safety of structural materials.

| S-EPMC4893737 | biostudies-other

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data