Amorphous Silicon Nanowires Grown on Silicon Oxide Film by Annealing.
Ontology highlight
ABSTRACT:
SUBMITTER: Yuan Z
PROVIDER: S-EPMC5552620 | biostudies-other | 2017 Aug
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Power devices (PD) are ubiquitous elements of the modern electronics industry that must satisfy the rigorous and diverse demands for robust power conversion systems that are essential for emerging technologies including Internet of Things (IoT), mobile electronics, and wearable devices. However, conventional PDs based on "bulk" and "single-crystal" semiconductors require high temperature (> 1000 °C) fabrication processing and a thick (typically a few tens to 100 μm) drift layer, thereby preventing their applications to compact devices, where PDs must be fabricated on a heat sensitive and flexible substrate. Here we report next-generation PDs based on "thin-films" of "amorphous" oxide semiconductors with the performance exceeding the silicon limit (a theoretical limit for a PD based on bulk single-crystal silicon). The breakthrough was achieved by the creation of an ideal Schottky interface without Fermi-level pinning at the interface, resulting in low specific on-resistance Ron,sp (< 1 × 10-4 Ω cm2) and high breakdown voltage VBD (~ 100 V). To demonstrate the unprecedented capability of the amorphous thin-film oxide power devices (ATOPs), we successfully fabricated a prototype on a flexible polyimide film, which is not compatible with the fabrication process of bulk single-crystal devices. The ATOP will play a central role in the development of next generation advanced technologies where devices require large area fabrication on flexible substrates and three-dimensional integration.
| S-EPMC8093298 | biostudies-literature
Project description:Amorphous Silicon-Tin-Oxide thin film transistors (a-STO TFTs) with Mo source/drain electrodes were fabricated. The introduction of a ~8?nm MoOx interlayer between Mo electrodes and a-STO improved the electron injection in a-STO TFT. Mo adjacent to the a-STO semiconductor mainly gets oxygen atoms from the oxygen-rich surface of a-STO film to form MoOx interlayer. The self-formed MoOx interlayer acting as an efficient interface modification layer could conduce to the stepwise internal transport barrier formation while blocking Mo atoms diffuse into a-STO layer, which would contribute to the formation of ohmic contact between Mo and a-STO film. It can effectively improve device performance, reduce cost and save energy for the realization of large-area display with high resolution in future.
| S-EPMC5841428 | biostudies-literature
Project description:Silicon nanowire chips can function as sensors for cancer DNA detection, whereby selective functionalization of the Si sensing areas over the surrounding silicon oxide would prevent loss of analyte and thus increase the sensitivity. The thermal hydrosilylation of unsaturated carbon-carbon bonds onto H-terminated Si has been studied here to selectively functionalize the Si nanowires with a monolayer of 1,8-nonadiyne. The silicon oxide areas, however, appeared to be functionalized as well. The selectivity toward the Si-H regions was increased by introducing an extra HF treatment after the 1,8-nonadiyne monolayer formation. This step (partly) removed the monolayer from the silicon oxide regions, whereas the Si-C bonds at the Si areas remained intact. The alkyne headgroups of immobilized 1,8-nonadiyne were functionalized with PNA probes by coupling azido-PNA and thiol-PNA by click chemistry and thiol-yne chemistry, respectively. Although both functionalization routes were successful, hybridization could only be detected on the samples with thiol-PNA. No fluorescence was observed when introducing dye-labeled noncomplementary DNA, which indicates specific DNA hybridization. These results open up the possibilities for creating Si nanowire-based DNA sensors with improved selectivity and sensitivity.
| S-EPMC6158678 | biostudies-literature
Project description:The radial junction (RJ) architecture has proven beneficial for the design of a new generation of high performance thin film photovoltaics. We herein carry out a comprehensive modeling of the light in-coupling, propagation and absorption profile within RJ thin film cells based on an accurate set of material properties extracted from spectroscopic ellipsometry measurements. This has enabled us to understand and evaluate the impact of varying several key parameters on the light harvesting in radially formed thin film solar cells. We found that the resonance mode absorption and antenna-like light in-coupling behavior in the RJ cell cavity can lead to a unique absorption distribution in the absorber that is very different from the situation expected in a planar thin film cell, and that has to be taken into account in the design of high performance RJ thin film solar cells. When compared to the experimental EQE response of real RJ solar cells, this modeling also provides an insightful and powerful tool to resolve the wavelength-dependent contributions arising from individual RJ units and/or from strong light trapping due to the presence of the RJ cell array.
| S-EPMC3950579 | biostudies-literature
Project description:Zinc oxide (ZnO) offers a great potential in several applications from sensors to Photovoltaic cells thanks to the material's dependency, to its optical and electrical properties and crystalline structure architypes. Typically, ZnO powder tends to be grown in the form of a wurtzite structure allowing versatility in the phase of material growths; albeit, whereas in this work we introduce an alternative in scalable yet relatively simple 2D hexagonal planed ZnO nanoflakes via the electrochemical deposition of commercially purchased Zn(NO?)? and KCl salts in an electrochemical process. The resulting grown materials were analyzed and characterized via a series of techniques prior to thermal annealing to increase the grain size and improve the crystal quality. Through observation via scanning electron microscope (SEM) images, we have analyzed the statistics of the grown flakes' hexagonal plane's size showing a non-monotonal strong dependency of the average flake's hexagonal flakes' on the annealing temperature, whereas at 300 °C annealing temperature, average flake size was found to be in the order of 300 ?m². The flakes were further analyzed via transmission electron microscopy (TEM) to confirm its hexagonal planes and spectroscopy techniques, such as Raman Spectroscopy and photo luminescence were applied to analyze and confirm the ZnO crystal signatures. The grown materials also underwent further characterization to gain insights on the material, electrical, and optical properties and, hence, verify the quality of the material for Photovoltaic cells' electron collection layer application. The role of KCl in aiding the growth of the less preferable (0001) ZnO is also investigated via various prospects discussed in our work. Our method offers a relatively simple and mass-producible method for synthesizing a high quality 2D form of ZnO that is, otherwise, technically difficult to grow or control.
| S-EPMC6120048 | biostudies-literature
Project description:Nanowires of ferroelectric potassium niobate were grown by filling nanoporous templates of both side opened anodic aluminum oxide (AAO) through radiofrequency vacuum sputtering for multisensor fabrication. The precise geometrical ordering of the AAO matrix led to well defined single axis oriented wire-shaped material inside the pores. The sensing abilities of the samples were studied and analyzed in terms of piezoelectric and pyroelectric response and the results were compared for different length of the nanopores (nanotubes)-1.3 µm, 6.3 µm and 10 µm. Based on scanning electronic microscopy, elemental and microstructural analyses, as well as electrical measurements at bending and heating, the overall sensing performance of the devices was estimated. It was found that the produced membrane type elements, consisting potassium niobate grown in AAO template exhibited excellent piezoelectric response due to the increased specific area as compared to non-structured films, and could be further enhanced with the nanowires length. The piezoelectric voltage increased linearly with 16 mV per micrometer of nanowire's length. At the same time the pyroelectric voltage was found to be less sensitive to the nanowires length, changing its value at 400 nV/µm. This paper provides a simple and low-cost approach for nanostructuring ferroelectric oxides with multisensing application, and serves as a base for further optimization of template based nanostructured devices.
| S-EPMC7179016 | biostudies-literature
Project description:When Si nanowires (NWs) have diameters below about 10 nm, their band gap increases as their diameter decreases; moreover, it can be direct if the material adopts the metastable diamond hexagonal structure. To prepare such wires, we have developed an original variant of the vapor-liquid-solid process based on the use of a bimetallic Cu-Sn catalyst in a plasma-enhanced chemical vapor deposition reactor, which allows us to prevent droplets from coalescing and favors the growth of a high density of NWs with a narrow diameter distribution. Controlling the deposited thickness of the catalyst materials at the sub-nanometer level allows us to get dense arrays (up to 6 × 1010 cm-2) of very-small-diameter NWs of 6 nm on average (standard deviation of 1.6 nm) with crystalline cores of about 4 nm. The transmission electron microscopy analysis shows that both 3C and 2H polytypes are present, with the 2H hexagonal diamond structure appearing in 5-13% of the analyzed NWs per sample.
| S-EPMC8515598 | biostudies-literature
Project description:This work reports the growth kinetics of amorphous nanowires (NWs) developed by the vapour-liquid-solid (VLS) mechanism. The model presented here incorporates all atomistic processes contributing to the growth of amorphous oxide NWs having diameters in the 5-100 nm range. The steady state growth condition has been described by balancing the key atomistic process steps. It is found that the 2D nano-catalyst liquid and NW solid (L-S) interface plays a central role in the kinetic analysis. The balance between the 2D Si layer crystallization and oxidation rate is quantitatively examined and compared with experimental values. The atomistic process dependencies of the NW growth rate, supersaturation (C/C 0), desolvation energy (Q D) barrier and NW diameter have been analyzed in detail. The model successfully predicts the reported NW growth rate to be in the range of 1-10 μm s-1. A novel seed/catalyst metal-based synthesis strategy for the preparation of amorphous silica NWs is reported. A nickel thin film on Si is used as a seed metal for the Au assisted VLS growth of silica NWs. The experimental results provide evidence of the creation of SiO under the given conditions followed by Si injection in the Au-Si nano-catalyst solution. The usage of seed metal was observed to reduce the growth temperature compared to the methods reported in the literature and obtain similar growth rates. The technique presented here holds promise for the synthesis of sub-100 nm diameter NWs.
| S-EPMC9418775 | biostudies-literature
Project description:In this paper, the photoluminescence (PL) of hydrogenated amorphous silicon carbide (a-Si1-xCx:H) thin films obtained by Plasma Enhancement Chemical Vapor Deposition (PECVD) is reported. Strong PL is obtained after a fast annealing process for 60 s at temperatures of 200, 400, 600, and 800 °C. The thin films are characterized using Fourier Transform Infrared spectroscopy (FTIR), PL spectroscopy, and Energy-Dispersive X-ray Spectroscopy (EDS). According to the results of the structural characterization, it is deduced that a structural rearrangement of the amorphous matrix is carried out during the fast annealing process, which results in different degrees of oxidation on the a-Si1-xCx:H films. The PL peak position shifts towards higher energies as the temperature increases. The sample deposited with a silane/methane flux ratio of 37.5 at an Radio Frequency (RF) power of 6 W experiences an increase in PL intensity of more than nine times, with a displacement in the peak position from 2.5 eV to 2.87 eV, at 800 °C. From the PL analysis, we observe two emission bands: one centered in the near infrared and other in the visible range (with a blue peak). This study opens the possibility to use such thin films in the development of optoelectronics devices, with potential for application in solar cells.
| S-EPMC7321575 | biostudies-literature
Project description:Low operating voltages have been long desired for thin-film transistors (TFTs). However, it is still challenging to realise 1-V operation by using conventional dielectrics due to their low gate capacitances and low breakdown voltages. Recently, electric double layers (EDLs) have been regarded as a promising candidate for low-power electronics due to their high capacitance. In this work, we present the first sputtered SiO2 solid-state electrolyte. In order to demonstrate EDL behaviour, a sputtered 200 nm-thick SiO2 electrolyte was incorporated into InGaZnO TFTs as the gate dielectric. The devices exhibited an operating voltage of 1 V, a threshold voltage of 0.06 V, a subthreshold swing of 83 mV dec-1 and an on/off ratio higher than 105. The specific capacitance was 0.45 µF cm-2 at 20 Hz, which is around 26 times higher than the value obtained from thermally oxidised SiO2 films with the same thickness. Analysis of the microstructure and mass density of the sputtered SiO2 films under different deposition conditions indicates that such high capacitance might be attributed to mobile protons donated by atmospheric water. The InGaZnO TFTs with the optimised SiO2 electrolyte also showed good air stability. This work provides a new pathway to the realisation of high-yield low-power electronics.
| S-EPMC5429786 | biostudies-literature