Kraus OA Targeted Proteomics Chingford Cohort
Ontology highlight
ABSTRACT:
INSTRUMENT(S): Xevo TQ-XS
ORGANISM(S): Homo Sapiens (ncbitaxon:9606)
SUBMITTER: 
Virginia Kraus
PROVIDER: MSV000091178 | MassIVE | Tue Jan 31 11:39:00 GMT 2023
REPOSITORIES: MassIVE
Similar Datasets
Project description:<p>The sample to be tested was fully ground into powder in the grinder, 50 mg of the sample was freeze-dried, 1000 μL of the extraction solution containing the inner target was added (methanol:acetonitrile:water, 2:2:1, v/v/v, internal standard concentration 20 mg/L) and vortex mixed for 30 s; then add the steel ball to the 45 Hz grinder for 10 min, ultrasonic 10 min; the sample to be tested is obtained after filtration. When detecting metabolites, metabolite determination was performed based on the LC-MS system, which mainly consists of Waters Acquity I-Class PLUS ultra-high performance liquid tandem and Waters Xevo G2-XS QTof high-resolution mass spectrometer. Meanwhile, the Waters Acquity UPLC HSS T3 column (1.8 um 2.1 x 100 mm) was used as the chromatographic column. Positive and negative ion modes were used to determine the metabolites. Mobile phase A: 0.1% formic acid aqueous solution; Mobile phase B: 0.1% acetonitrile formate. The mobile phase conditions of liquid chromatography were as follows: the flow rate was 400 μL/min, 0.0 min: 98% flow A, 2% flow B; 0.25 min: 98% flow A, 2% flow B, 10.0 min: 2% flow A, 98% flow B; 13.0 min: 2% flow A, 98% flow B; 13.1 min: 98% flow A, 2% flow B; 15.0 min: 98% flow A, 2% flow B. MSe mode controlled by acquisition software (MassLynx v4.2, Waters) was used for primary and secondary mass spectrum data acquisition. ESI ion source parameters are as follows: Capillary voltage, 2500 V (positive ion mode) or -2000 V (negative ion mode); Cone hole voltage, 30 V; Ion source temperature, 100 °C; Desolvent temperature, 500 °C; Air flow rate, 50 L/h; Desolvent gas flow rate, 800 L/h; Plastic-nucleus ratio (m/z) collection range 50-1200 m/z. In the qualitative and quantitative analysis of metabolites, the original data collected by MassLynx v4.2 were processed by the Progenesis QI software for peak extraction, peak alignment, and other data, and the metabolites were identified based on the Progenesis QI software online METLIN database. Then, based on the results of the total score, MS2 score, and mass error (ppm), the metabolites were qualitatively determined.</p>
2024-07-12 | MTBLS10002 | MetaboLights
Project description:Human primary macrophages were infected with influenza A virus (H3N2/Udorn strain, HA 256) for 6 hrs or left untreated. Cells were collected and lysed with HEPES lysis buffer (50 mM HEPES, 150 mM NaCl, 1 mM EDTA, 1 % NP-40, pH 7.4) including protease and phosphatase inhibitor cocktails. The cell lysates were centrifuged and the supernatant was collected and the protein content was measured with Bio-Rad DC™ protein assay (Bio-Rad). The proteins were reduced, alkylated, and enzymatically digested in-solution with trypsin. The digestion was stopped by adding FA (final c = 1 %). The samples were centrifuged 9168 x g for 10 min and desalted with Sep-Pak Vac RP C18 cartridges (Waters, MA, USA), following fractionation by strong cation exchange chromatography (SCX). The peptides were separated on a 200 x 4.6 mm, 5 μm, 200 Å PolySULFOETHYL A™ column (PolyLC, USA). The fractions were vacuum centrifuged and desalted as before, following phosphopeptide-enrichment with PHOS-Select™ Iron Affinity Gel (Sigma Aldrich, MO, USA). LC-MS/MS was performed with a Q Exactive hybrid quadrupole-orbitrap tandem mass spectrometer coupled to an EASY-nLC 1000 nanoflow liquid chromatograph (Thermo Fisher Scientific). A 100 μm x 3 cm trap column and a 75 μm x 15 cm analytical column were in-house packed with Magic C18AQ resin (200 Å, 5 μm; Michrom Bioresources). The mobile phases were 2% acetonitrile, 0.2% formic acid (A) and 95% acetonitrile, 0.2% formic acid (B). LC gradient elution condition was 2% B (0 min), 20% B (70 min), 40% B (100 min), and then 100% B (105-110 min), with a flow rate of 300 nl/min. Data dependent acquisition was performed in positive ion mode. MS spectra were acquired from m/z 300 to m/z 2000 at a resolution of 70,000 at m/z 200 with a target value of 1,000,000 and maximum injection time of 120 ms. The 10 most abundant precursor ions of which charge states were 2+ or higher were selected for higher energy collisional dissociation (HCD) with an isolation window of 2 and normalized collision energy of 30. MS/MS spectra were acquired at a resolution of 17,500 at m/z 200 with a target value of 50,000, maximum injection time of 250 ms, and the lowest mass fixed at m/z 100. Dynamic exclusion duration was 30 s.
2016-08-08 | PXD001620 | Pride
Project description:Cervicovaginal lavage (CVL)supernatants were heat inactivated for 30 minutes at 56°C before further processing. Total protein concentrations were determined using the Pierce Coomassie Plus (Bradford) Protein Assay (Thermo Scientific, Rockford, IL, USA). Sample protein content and volume were normalised with 25mM ammonium bicarbonate (ABC). Soluble proteins were precipitated using an equal volume of ice cold 30% (w/v) TCA in acetone and incubated at -20⁰C for 2 hours. Samples were centrifuged at 12,000g for 10 minutes (4⁰C) to pellet proteins. Pellets were washed three times with ice cold acetone and allowed to air dry. Further sample processing was performed as previously described (Armstrong et al, 2014) with minor modifications. Briefly, protein pellets were resuspended in 25 mM ABC, 0.05%(w/v) rapigest (Waters), reduced and alkylated. Digestion was performed with proteomic-grade trypsin (Sigma-Aldrich, St. Louis, MO, USA) at a protein:trypsin ratio of 50:1. Rapigest was precipitated by addition of trifluoroacetic acid to a final concentration of 0.5% (v/v). Peptide mixtures were analyzed by on-line nanoflow liquid chromatography using the nanoACQUITY-nLC system (Waters MS technologies) coupled to an LTQ-Orbitrap Velos (ThermoFisher Scientific, Bremen, Germany) mass spectrometer equipped with the manufacturer’s nanospray ion source. The gradient of the analytic column (nanoACQUITY UPLCTM BEH130 C18 15cm x 75µm, 1.7µm capillary column) consisted of 3-40% acetonitrile in 0.1% formic acid for 90 min then a ramp of 40-85% acetonitrile in 0.1% formic acid for 5min.
2016-03-15 | PXD003176 | Pride
Project description:Quantitative LC/MS/MS was performed on 2 uL of each sample, using a nanoAcquity UPLC system (Waters Corp) coupled to a Thermo Orbitrap Fusion Lumos high resolution accurate mass tandem mass spectrometer (Thermo) via a nanoelectrospray ionization source. Briefly, the sample was first trapped on a Symmetry C18 20 mm x 180 um trapping column (5 ul/min at 99.9/0.1 v/v water/acetonitrile), after which the analytical separation was performed using a 1.8 um Acquity HSS T3 C18 75 um x 250 mm column (Waters Corp.) with a 90-min linear gradient of 5 to 30% acetonitrile with 0.1% formic acid at a flow rate of 400 nanoliters/minute (nL/min) with a column temperature of 55C. Data collection on the Fusion Lumos mass spectrometer was performed in a data-dependent acquisition (DDA) mode of acquisition with a r=120,000 (m/z 200) full MS scan from m/z 375 - 1500 with a target AGC value of 2e5 ions. MS/MS scans were acquired at Rapid scan rate (Ion Trap) with an AGC target of 5e3 ions and a max injection time of 100 ms. The total cycle time for MS and MS/MS scans was 2 sec. A 20s dynamic exclusion was employed to increase depth of coverage. The total analysis cycle time for each sample injection was approximately 2 hours.
2022-12-05 | MSV000090835 | MassIVE
Project description:Quantitative LC-MS/MS was performed on 4 uL of each sample, using a nanoAcquity UPLC system (Waters Corp) coupled to a Thermo Orbitrap Fusion Lumos high resolution accurate mass tandem mass spectrometer (Thermo) via a nanoelectrospray ionization source. Briefly, the sample was first trapped on a Symmetry C18 20 mm x 180 um trapping column (5 ul/min at 99.9/0.1 v/v water/acetonitrile), after which the analytical separation was performed using a 1.8 um Acquity HSS T3 C18 75 um x 250 mm column (Waters Corp.) with a 90-min linear gradient of 3 to 30% acetonitrile with 0.1% formic acid at a flow rate of 400 nanoliters/minute (nL/min) with a column temperature of 55C. Data collection on the Fusion Lumos mass spectrometer was performed in a data-dependent acquisition (DDA) mode of acquisition with a r=120,000 (m/z 200) full MS scan from m/z 375 - 1500 with a target AGC value of 2e5 ions. MS/MS scans were acquired at Rapid scan rate (Ion Trap) with an AGC target of 5e3 ions and a max injection time of 200 ms. The total cycle time for MS and MS/MS scans was 2 sec. A 20 sec dynamic exclusion was employed to increase depth of coverage. The total analysis cycle time for each sample injection was approximately 2 hours.
2021-06-15 | MSV000087623 | MassIVE
Project description:Qualitative LC MS/MS was performed on 4 uL of each sample, using a nanoAcquity UPLC system (Waters Corp) coupled to a Thermo Orbitrap Fusion Lumos high resolution accurate mass tandem mass spectrometer (Thermo) via a nanoelectrospray ionization source. Briefly, the sample was first trapped on a Symmetry C18 20 mm x 180 um trapping column (5 ul/min at 99.9/0.1 v/v water/acetonitrile), after which the analytical separation was performed using a 1.8 um Acquity HSS T3 C18 75 um x 250 mm column (Waters Corp.) with a 90-min linear gradient of 3 to 30% acetonitrile with 0.1% formic acid at a flow rate of 400 nanoliters/minute (nL/min) with a column temperature of 55C. Data collection on the Fusion Lumos mass spectrometer was performed in a data dependent acquisition (DDA) mode of acquisition with a r=120,000 (@ m/z 200) full MS scan from m/z 375 to 1500 with a target AGC value of 2e5 ions. MS/MS scans were acquired at Rapid scan rate (Ion Trap) with an AGC target of 5e3 ions and a max injection time of 200 ms. The total cycle time for MS and MS/MS scans was 2 sec. A 20 sec dynamic exclusion was employed to increase depth of coverage. The total analysis cycle time for each sample injection was approximately 2 hours.
2021-06-14 | MSV000087618 | MassIVE
Project description:Pretreated human follicular fluid was prepared for targeted metabolomics experiments. For this purpose, 12-point standard calibration curves in the respective range with reference material were measured, and the limit of detection (LOD) and limit of quantification (LOQ) for each neurotransmitter under investigation were calculated. LC-MS/MS was conducted by an ultra-performance liquid chromatography method using a Waters ACQUITY UPLC BEH C18 column (2.1 mm×100 mm, 1.7 µm, Waters, USA). The Waters acquisition UPLC was coupled to an API 4000 triple quadrupole mass spectrometer (AB SCIEX, USA). The mobile phase A buffer was 10% methanol in water (containing 0.1% formic acid), and the mobile phase B buffer was 50% methanol in water (containing 0.1% formic acid). The LC gradient elution was at a flow rate of 0.3 mL/min at 0-8.0 min and 0.4 ml/min at 8.0-17.5 min, then 10%-30% B at 0-6.5 min; 30%-100% B at 6.5-7 min; 100% B at 7-14min; and 100%-10% B at 14-17.5min. The injection volume was 5 µl and the column temperature was set to 40 °C. Twenty-three metabolites (Ach: Acetylcholine chloride; Gln: Glutamine; Glu: Glutamate; His: L-Histidine; NE: norepinephrine; Tyr:Tyrosine; Trp:Tryptophan; Kyn: Kynurenine; GABA: 4-Aminobutyric acid;HisA:Histamine; PA:Picolinic acid;TyrA:Tyramine;DA:Hydroxytyramine hydrochloride; TrpA:Tryptamine;5-HT:Serotonin hydrochloride;E:Adrenaline hydrochloride;KynA:Kynurenic acid;5-HIAA:5-Hydroxyindole-3-acetic acid;DOPA:Levodopa;XA:Xanthurenic acid;VWA:Vanillymandelic Acid; 5-HTTP:5-Hydroxytryptophan;MT:Melatonine)were simultaneously reported in LC-MS/MS multiple reaction monitoring (MRM) mode. Data analysis was performed with Analyst 1.6 software.
2022-08-12 | PXD031560 | Pride
Project description:Quantitative LC/MS/MS was performed on 2 uL using an MClass UPLC system (Waters Corp) coupled to a Thermo Orbitrap Fusion Lumos high resolution accurate mass tandem mass spectrometer (Thermo) equipped with a FAIMSPro device via a nanoelectrospray ionization source. Briefly, the sample was first trapped on a Symmetry C18 20 mm x 180 um trapping column (5 ul/min at 99.9/0.1 v/v water/acetonitrile), after which the analytical separation was performed using a 1.8 um Acquity HSS T3 C18 75 um x 250 mm column (Waters Corp.) with a 90-min linear gradient of 5 to 30% acetonitrile with 0.1% formic acid at a flow rate of 400 nanoliters/minute (nL/min) with a column temperature of 55C. Data collection on the Fusion Lumos mass spectrometer was performed for three difference compensation voltages (-40v, -60v, -80v). Within each CV, a data-dependent acquisition (DDA) mode of acquisition with a r 120,000 (m/z 200) full MS scan from m/z 375 - 1500 with a target AGC value of 4e5 ions was performed. MS/MS scans were acquired in the ion trap in Rapid mode with a target AGC value of 1e4 and max fill time of 35 ms. The total cycle time for each CV was 0.66s, with total cycle times of 2 sec between like full MS scans. A 20s dynamic exclusion was employed to increase depth of coverage. The total analysis cycle time for each injection was approximately 2 hou
2023-03-03 | MSV000091407 | MassIVE
Project description:Quantitative LC/MS/MS was performed on 2 uL using an MClass UPLC system (Waters Corp) coupled to a Thermo Orbitrap Fusion Lumos high resolution accurate mass tandem mass spectrometer (Thermo) equipped with a FAIMSPro device via a nanoelectrospray ionization source. Briefly, the sample was first trapped on a Symmetry C18 20 mm x 180 um trapping column (5 ul/min at 99.9/0.1 v/v water/acetonitrile), after which the analytical separation was performed using a 1.8 um Acquity HSS T3 C18 75 um x 250 mm column (Waters Corp.) with a 90-min linear gradient of 5 to 30% acetonitrile with 0.1% formic acid at a flow rate of 400 nanoliters/minute (nL/min) with a column temperature of 55C. Data collection on the Fusion Lumos mass spectrometer was performed for three difference compensation voltages (-40v, -60v, -80v). Within each CV, a data-dependent acquisition (DDA) mode of acquisition with a r 120,000 (m/z 200) full MS scan from m/z 375 - 1500 with a target AGC value of 4e5 ions was performed. MS/MS scans were acquired in the ion trap in Rapid mode with a target AGC value of 1e4 and max fill time of 35 ms. The total cycle time for each CV was 0.66s, with total cycle times of 2 sec between like full MS scans. A 20s dynamic exclusion was employed to increase depth of coverage. The total analysis cycle time for each injection was approximately 2 hours.
2023-04-04 | MSV000091630 | MassIVE
Project description:Quantitative LC/MS/MS was performed on 2 uL using an MClass UPLC system (Waters Corp) coupled to a Thermo Orbitrap Fusion Lumos high resolution accurate mass tandem mass spectrometer (Thermo) equipped with a FAIMSPro device via a nanoelectrospray ionization source. Briefly, the sample was first trapped on a Symmetry C18 20 mm x 180 um trapping column (5 ul/min at 99.9/0.1 v/v water/acetonitrile), after which the analytical separation was performed using a 1.8 um Acquity HSS T3 C18 75 um x 250 mm column (Waters Corp.) with a 90-min linear gradient of 5 to 30% acetonitrile with 0.1% formic acid at a flow rate of 400 nanoliters/minute (nL/min) with a column temperature of 55C. Data collection on the Fusion Lumos mass spectrometer was performed for three difference compensation voltages (-40v, -60v, -80v). Within each CV, a data-dependent acquisition (DDA) mode of acquisition with a r 120,000 (m/z 200) full MS scan from m/z 375 - 1500 with a target AGC value of 4e5 ions was performed. MS/MS scans were acquired in the ion trap in Rapid mode with a target AGC value of 1e4 and max fill time of 35 ms. The total cycle time for each CV was 0.66s, with total cycle times of 2 sec between like full MS scans. A 20s dynamic exclusion was employed to increase depth of coverage. The total analysis cycle time for each injection was approximately 2 hours.
2023-03-09 | MSV000091457 | MassIVE