Inertial focusing cytometer with integrated optics for particle characterization.
Ontology highlight
ABSTRACT:
SUBMITTER: Kotz KT
PROVIDER: S-EPMC4206911 | biostudies-literature | 2013
REPOSITORIES: biostudies-literature
Publications
Inertial focusing cytometer with integrated optics for particle characterization.
Kotz Kenneth T KT Petrofsky Anne C AC Haghgooie Ramin R Granier Robert R Toner Mehmet M Tompkins Ronald G RG
Technology 20130101 1
Microfluidic inertial focusing has been shown as a simple and effective method to localize cells and particles within a flow cell for interrogation by an external optical system. To enable portable point of care optical cytometry, however, requires a reduction in the complexity of the large optical systems that are used in standard flow cytometers. Here, we present a new design that incorporates optical waveguides and focusing elements with an inertial focusing flow cell to make a compact robust ...[more]
Similar Datasets
Project description:Three-dimensional (3D) particle focusing in microfluidics is a fundamental capability with a wide range of applications, such as on-chip flow cytometry, where high-throughput analysis at the single-cell level is performed. Currently, 3D focusing is achieved mainly in devices with complex layouts, additional sheath fluids, and complex pumping systems. In this work, we present a compact microfluidic device capable of 3D particle focusing at high flow rates and with a small footprint, without the requirement of external fields or lateral sheath flows, but using only a single-inlet, single-outlet microfluidic sequence of straight channels and tightly curving vertical loops. This device exploits inertial fluidic effects that occur in a laminar regime at sufficiently high flow rates, manipulating the particle positions by the combination of inertial lift forces and Dean drag forces. The device is fabricated by femtosecond laser irradiation followed by chemical etching, which is a simple two-step process enabling the creation of 3D microfluidic networks in fused silica glass substrates. The use of tightly curving three-dimensional microfluidic loops produces strong Dean drag forces along the whole loop but also induces an asymmetric Dean flow decay in the subsequent straight channel, thus producing rapid cross-sectional mixing flows that assist with 3D particle focusing. The use of out-of-plane loops favors a compact parallelization of multiple focusing channels, allowing one to process large amounts of samples. In addition, the low fluidic resistance of the channel network is compatible with vacuum driven flows. The resulting device is quite interesting for high-throughput on-chip flow cytometry.
| S-EPMC6444990 | biostudies-literature
Project description:Inertial microfluidics (i.e., migration and focusing of particles in finite Reynolds number microchannel flows) is a passive, precise, and high-throughput method for microparticle manipulation and sorting. Therefore, it has been utilized in numerous biomedical applications including phenotypic cell screening, blood fractionation, and rare-cell isolation. Nonetheless, the applications of this technology have been limited to larger bioparticles such as blood cells, circulating tumor cells, and stem cells, because smaller particles require drastically longer channels for inertial focusing, which increases the pressure requirement and the footprint of the device to the extent that the system becomes unfeasible. Inertial manipulation of smaller bioparticles such as fungi, bacteria, viruses, and other pathogens or blood components such as platelets and exosomes is of significant interest. Here, we show that using oscillatory microfluidics, inertial focusing in practically "infinite channels" can be achieved, allowing for focusing of micron-scale (i.e. hundreds of nanometers) particles. This method enables manipulation of particles at extremely low particle Reynolds number (Rep < 0.005) flows that are otherwise unattainable by steady-flow inertial microfluidics (which has been limited to Rep > ∼10-1). Using this technique, we demonstrated that synthetic particles as small as 500 nm and a submicron bacterium, Staphylococcus aureus, can be inertially focused. Furthermore, we characterized the physics of inertial microfluidics in this newly enabled particle size and Rep range using a Peclet-like dimensionless number (α). We experimentally observed that α >> 1 is required to overcome diffusion and be able to inertially manipulate particles.
| S-EPMC6065022 | biostudies-literature
Project description:A passive, continuous and size-dependent focusing technique enabled by "inertial microfluidics", which takes advantage of hydrodynamic forces, is implemented in this study to focus microparticles. The objective is to analyse the decoupling effects of inertial forces and Dean drag forces on microparticles of different sizes in curvilinear microchannels with inner radius of 800??m and curvature angle of 280°, which have not been considered in the literature related to inertial microfluidics. This fundamental approach gives insight into the underlying physics of particle dynamics and offers continuous, high-throughput, label-free and parallelizable size-based particle separation. Our design allows the same footprint to be occupied as straight channels, which makes parallelization possible with optical detection integration. This feature is also useful for ultrahigh-throughput applications such as flow cytometers with the advantages of reduced cost and size. The focusing behaviour of 20, 15 and 10??m fluorescent polystyrene microparticles was examined for different channel Reynolds numbers. Lateral and vertical particle migrations and the equilibrium positions of these particles were investigated in detail, which may lead to the design of novel microfluidic devices with high efficiency and high throughput for particle separation, rapid detection and diagnosis of circulating tumour cells with reduced cost.
| S-EPMC5171716 | biostudies-literature
Project description:Flow focusing microfluidic devices (FFMDs) have been investigated for the production of monodisperse populations of microbubbles for chemical, biomedical and mechanical engineering applications. High-speed optical microscopy is commonly used to monitor FFMD microbubble production parameters, such as diameter and production rate, but this limits the scalability and portability of the approach. In this work, a novel FFMD design featuring integrated electronics for measuring microbubble diameters and production rates is presented. A micro Coulter particle counter (?CPC), using electrodes integrated within the expanding nozzle of an FFMD (FFMD-?CPC), was designed, fabricated and tested. Finite element analysis (FEA) of optimal electrode geometry was performed and validated with experimental data. Electrical data was collected for 8-20 ?m diameter microbubbles at production rates up to 3.25 × 105 MB s-1 and compared to both high-speed microscopy data and FEA simulations. Within a valid operating regime, Coulter counts of microbubble production rates matched optical reference values. The Coulter method agreed with the optical reference method in evaluating the microbubble diameter to a coefficient of determination of R2 = 0.91.
| S-EPMC6566100 | biostudies-literature
Project description:By experimentally studying high-order harmonic beams generated in gases, we show how the spatial characteristics of these ultrashort extreme-ultraviolet (XUV) beams can be finely controlled when a single fundamental beam generates harmonics in a thin gas medium. We demonstrate that these XUV beams can be emitted as converging beams and thereby get focused after generation. We study this optics-less focusing using a spatially chirped beam that acts as a probe located inside the harmonic generation medium. We analyze the XUV beam evolution with an analytical model and obtain very good agreement with experimental measurements. The XUV foci sizes and positions vary strongly with the harmonic order, and the XUV waist can be located at arbitrarily large distances from the generating medium. We discuss how intense XUV fields can be obtained with optics-less focusing and how the order-dependent XUV beam characteristics are compatible with broadband XUV irradiation and attosecond science.
| S-EPMC6450687 | biostudies-literature
Project description:This report details a comprehensive study of inertial focusing dynamics and particle behavior in low aspect ratio (h/w ∼ 1/1 to 1/8) spiral microchannels. A continuum of particle streak behavior is shown with longitudinal, cross-sectional, and velocity resolution, yielding a large analyzed parameter space. The dataset is then summarized and compared to prior results from both straight microchannels and other low aspect ratio spiral microchannel designs. Breakdown of focusing into a primary and secondary fluorescent streak is observed in the lowest aspect ratio channels at high average downstream velocities. Streak movement away from the theoretically predicted near inner wall equilibrium position towards the center of the channel at high average downstream velocities is also detailed as a precursor to breakdown. State diagrams detail the overall performance of each device including values of the required channel lengths and the range of velocities over which quality focusing can be achieved.
| S-EPMC3311666 | biostudies-other
Project description:In this work, we design and fabricate a miniaturized spiral-shaped microchannel device which can be used for high-throughput particle/cell ordering, enrichment, and purification. To probe into the flow rate regulation mechanism, an experimental investigation is carried out on the focusing behaviors of particles with significantly different sizes in this device. A complete picture of the focusing position shifting process is unfolded to clarify the confusing results obtained from flow regimes with different dominant forces in past research. Specifically, with the increase of the flow rate, particles are observed to first move towards the inner wall under the dominant inertial migration, then stabilize at a specific position and finally shift away from the inner wall due to the alternation of the dominant force. Novel phenomena of focusing instability, co-focusing, and focusing position interchange of differently sized particles are also observed and investigated. Based on the obtained experimental data, we develop and validate, for the first time, a five-stage model of the particle focusing process with increasing flow rate for interpreting particle behaviors in terms of the competition between inertial lift and Dean drag forces. These new experimental findings and the proposed process model provide an important supplement to the existing mechanism of inertial particle flow and enable more flexible and precise particle manipulation. Additionally, we examine the focusing behaviors of bioparticles with a polydisperse size distribution to validate the explored mechanisms and thus help realize efficient enrichment and purification of these particles.
| S-EPMC3751952 | biostudies-other
Project description:Due to their short wavelength, X-rays can in principle be focused down to a few nanometres and below. At the same time, it is this short wavelength that puts stringent requirements on X-ray optics and their metrology. Both are limited by today's technology. In this work, we present accurate at wavelength measurements of residual aberrations of a refractive X-ray lens using ptychography to manufacture a corrective phase plate. Together with the fitted phase plate the optics shows diffraction-limited performance, generating a nearly Gaussian beam profile with a Strehl ratio above 0.8. This scheme can be applied to any other focusing optics, thus solving the X-ray optical problem at synchrotron radiation sources and X-ray free-electron lasers.
| S-EPMC5337966 | biostudies-literature
Project description:Controlling and manipulating the polarization state of a light beam is crucial in applications ranging from optical sensing to optical communications, both in the classical and quantum regime, and ultimately whenever interference phenomena are to be exploited. In addition, many of these applications present severe requirements of phase stability and greatly benefit from a monolithic integrated-optics approach. However, integrated devices that allow arbitrary transformations of the polarization state are very difficult to produce with conventional lithographic technologies. Here we demonstrate waveguide-based optical waveplates, with arbitrarily rotated birefringence axis, fabricated by femtosecond laser pulses. To validate our approach, we exploit this component to realize a compact device for the quantum state tomography of two polarization-entangled photons. This work opens perspectives for integrated manipulation of polarization-encoded information with relevant applications ranging from integrated polarimetric sensing to quantum key distribution.
| S-EPMC4083439 | biostudies-literature
Project description:Inertial microfluidics utilizing passive hydrodynamic forces has been attracting significant attention in the field of precise microscale manipulation owing to its low cost, simplicity and high throughput. In this paper, we present a novel channel design with a series of reverse wavy channel structures for sheathless inertial particle focusing and cell sorting. A single wavy channel unit consists of four semicircular segments, which produce periodically reversed Dean secondary flow along the cross-section of the channel. The balance between the inertial lift force and the Dean drag force results in deterministic equilibrium focusing positions, which also depends on the size of the flow-through particles and cells. Six sizes of fluorescent microspheres (15, 10, 7, 5, 3 and 1 μm) were used to study the size-dependent inertial focusing behavior. Our novel design with sharp-turning subunits could effectively focus particles as small as 3 μm, the average size of platelets, enabling the sorting of cancer cells from whole blood without the use of sheath flows. Utilizing an optimized channel design, we demonstrated the size-based sorting of MCF-7 breast cancer cells spiked in diluted whole blood samples without using sheath flows. A single sorting process was able to recover 89.72% of MCF-7 cells from the original mixture and enrich MCF-7 cells from an original purity of 5.3% to 68.9% with excellent cell viability.
| S-EPMC6220157 | biostudies-literature