Dataset Information

Mechanical Fracturing of Core-Shell Undercooled Metal Particles for Heat-Free Soldering.

ABSTRACT: Phase-change materials, such as meta-stable undercooled (supercooled) liquids, have been widely recognized as a suitable route for complex fabrication and engineering. Despite comprehensive studies on the undercooling phenomenon, little progress has been made in the use of undercooled metals, primarily due to low yields and poor stability. This paper reports the use of an extension of droplet emulsion technique (SLICE) to produce undercooled core-shell particles of structure; metal/oxide shell-acetate ('/'?= physisorbed, '-'?= chemisorbed), from molten Field's metal (Bi-In-Sn) and Bi-Sn alloys. These particles exhibit stability against solidification at ambient conditions. Besides synthesis, we report the use of these undercooled metal, liquid core-shell, particles for heat free joining and manufacturing at ambient conditions. Our approach incorporates gentle etching and/or fracturing of outer oxide-acetate layers through mechanical stressing or shearing, thus initiating a cascade entailing fluid flow with concomitant deformation, combination/alloying, shaping, and solidification. This simple and low cost technique for soldering and fabrication enables formation of complex shapes and joining at the meso- and micro-scale at ambient conditions without heat or electricity.

SUBMITTER: C?nar S

PROVIDER: S-EPMC4763186 | biostudies-literature | 2016 Feb

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Mechanical Fracturing of Core-Shell Undercooled Metal Particles for Heat-Free Soldering.

Çınar Simge S Tevis Ian D ID Chen Jiahao J Thuo Martin M

Scientific reports 20160223

Phase-change materials, such as meta-stable undercooled (supercooled) liquids, have been widely recognized as a suitable route for complex fabrication and engineering. Despite comprehensive studies on the undercooling phenomenon, little progress has been made in the use of undercooled metals, primarily due to low yields and poor stability. This paper reports the use of an extension of droplet emulsion technique (SLICE) to produce undercooled core-shell particles of structure; metal/oxide shell-a ...[more]

PMID: 26902483

Similar Datasets

Project description:Magnetic materials in sample preparation for shotgun phosphoproteomics offer several advantages over conventional systems, as the enrichment can be achieved directly in solution, but they still suffer from some drawbacks, due to limited stability and selectivity, which is supposed to be affected by the hydrophilicity of the polymeric supports used for cation immobilization. The paper describes the development of an improved magnetic material with increased stability, thanks to a two-step covering of the magnetic core, for the enrichment of phosphopeptides in biological samples. Four materials were prepared featuring a polymeric shell with tunable hydrophilicity, obtained by "grafting from" polymerization of glycidyl methacrylate with 0-8.3% of polyethylene glycol methacrylate (PEGMA), the latter used to modulate the hydrophilicity of the material surface. Finally, the materials were functionalized with iminodiacetic acid for Ti4+ ion immobilization. The materials were analyzed for their composition by a combination of CHN elemental analysis and thermogravimetric analysis, also hyphenated to gas chromatography and mass spectrometric detection. Surface characteristics were evaluated by water contact angle measurements, scanning electron microscopy and energy dispersive X-ray spectrometry. These materials were applied to the enrichment of phosphopeptides from yeast protein digests. Peptides were identified by proteomics techniques using nano-high performance liquid chromatography coupled to mass spectrometry and bioinformatics. Qualitatively the peptides identified by the four systems were comparable, with 1606-1693 phosphopeptide identifications and a selectivity of 47-54% for all materials. The physico-chemical features of the identified peptides were also the same for the four materials. In particular, the grand average of hydropathy index values indicated that the enriched phosphopeptides were hydrophilic (ca. 90%), and only some co-enriched non-phosphorylated peptides were hydrophobic (21-28%), regardless of the material used for enrichment. Peptides had a pI???7, which indicated a well-known bias for acidic peptides binding, attributed to the interaction with the metal center itself. The results indicated that the enrichment of phosphopeptides and the co-enrichment of non-phosphorylated peptides is mainly driven by interactions with Ti4+ and does not depend on the amount of PEGMA chains in the polymer shell.

Dataset Information

Mechanical Fracturing of Core-Shell Undercooled Metal Particles for Heat-Free Soldering.

Publications

Mechanical Fracturing of Core-Shell Undercooled Metal Particles for Heat-Free Soldering.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets