Browse
Submit Data
Databases
API
Help

Dataset Information

39 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

A one-step route to solubilised, purified or functionalised single-walled carbon nanotubes.

ABSTRACT: Reductive dissolution is a promising processing route for single walled carbon nanotubes (SWCNTs) that avoids the damage caused by ultrasonication and aggressive oxidation whilst simultaneously allowing access to a wealth of SWCNT functionalisation reactions. Here, reductive dissolution has been simplified to a single one-pot reaction through the use of sodium naphthalide in dimethylacetamide allowing direct synthesis of SWCNT Na⁺ solutions. Gram quantities of SWCNTs can be dissolved at concentrations over 2 mg mL^-1. These reduced SWCNT solutions can easily be functionalised through the addition of alkyl halides; reducing steric bulk of the grafting moiety and increasing polarisability of the leaving group increases the extent of functionalisation. An optimised absolute sodium concentration of 25 mM is shown to be more important than carbon to metal ratio in determining the maximum degree of functionalisation. This novel dissolution system can be modified for use as a non-destructive purification route for raw SWCNT powder by adjusting the degree of charging to dissolve carbonaceous impurities, catalyst particles and defective material, before processing the remaining SWCNTs.

SUBMITTER: Clancy AJ

PROVIDER: S-EPMC4786951 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Pseudocapacitive Effects of Multi-Walled Carbon Nanotubes-Functionalised Spinel Copper Manganese Oxide.

Project description:Spinel copper manganese oxide nanoparticles combined with acid-treated multi-walled carbon nanotubes (CuMn2O4/MWCNTs) were used in the development of electrodes for pseudocapacitor applications. The CuMn2O4/MWCNTs preparation involved initial synthesis of Mn3O4 and CuMn2O4 precursors followed by an energy efficient reflux growth method for the CuMn2O4/MWCNTs. The CuMn2O4/MWCNTs in a three-electrode cell assembly and in 3 M LiOH aqueous electrolyte exhibited a specific capacitance of 1652.91 F g-1 at 0.5 A g-1 current load. Similar investigation in 3 M KOH aqueous electrolyte delivered a specific capacitance of 653.41 F g-1 at 0.5 A g-1 current load. Stability studies showed that after 6000 cycles, the CuMn2O4/MWCNTs electrode exhibited a higher capacitance retention (88%) in LiOH than in KOH (64%). The higher capacitance retention and cycling stability with a Coulombic efficiency of 99.6% observed in the LiOH is an indication of a better charge storage behaviour in this electrolyte than in the KOH electrolyte with a Coulombic efficiency of 97.3%. This superior performance in the LiOH electrolyte than in the KOH electrolyte is attributed to an intercalation/de-intercalation mechanism which occurs more easily in the LiOH electrolyte than in the KOH electrolyte.

| S-EPMC9565235 | biostudies-literature

One-step sorting of single-walled carbon nanotubes using aqueous two-phase extraction in the presence of basic salts.

Project description:We demonstrate a simple one-step approach to separate (6,5) CNTs from raw material by using the aqueous two-phase extraction method. To reach this goal, stable and inexpensive K2CO3, Na2CO3, Li2CO3, and K3PO4 basic salts are used as modulators of the differentiation process. Under the appropriate parameters, near monochiral fractions become available for straightforward harvesting. In parallel, we show that the isolation process is strongly affected not only by pH but by the inherent nature of the introduced chemical species as well. The results of our study also reveal that the commonly used ingredients of the biphasic system make a strong contribution to the course of the separation by having far from neutral pH values themselves.

| S-EPMC7280227 | biostudies-literature

Single-step extraction of small-diameter single-walled carbon nanotubes in the presence of riboflavin.

Project description:We propose a novel approach to disperse and extract small-diameter single-walled carbon nanotubes (SWCNTs) using an aqueous solution of riboflavin and Sephacryl gel. The extraction of small-diameter semiconducting SWCNTs was observed, regardless of the initial diameter distribution of the SWCNTs. Dispersion of SWCNTs occurs due to the adsorption of π-conjugated isoalloxazine moieties on the surface of small-diameter nanotubes and interactions between hydroxy groups of ribityl chains with water. During the SWCNT extraction, specific adsorption of riboflavin to SWCNTs leads to the minimization of interactions between the SWCNTs and gel media. Our experimental findings are supported by ab initio calculations demonstrating the impact of the riboflavin wrapping pattern around the SWCNTs on their interaction with the allyl dextran gel.

| S-EPMC9795860 | biostudies-literature

Enzyme immobilisation on amino-functionalised multi-walled carbon nanotubes: structural and biocatalytic characterisation.

Project description:BackgroundThe aim of this work is to investigate the structure and function of enzymes immobilised on nanomaterials. This work will allow better understanding of enzyme-nanomaterial interactions, as well as designing functional protein-nanomaterial conjugates.Methodology/principal findingsMultiwalled carbon nanotubes (MWNTs) were functionalised with amino groups to improve solubility and biocompatibility. The pristine and functionalised forms of MWNTs were characterised with Fourier-transform infrared spectroscopy. Thermogravimetric analysis was done to examine the degree of the functionalisation process. An immobilised biocatalyst was prepared on functionalised nanomaterial by covalent binding. Thermomyces lanuginosus lipase was used as a model enzyme. The structural change of the immobilised and free lipases were characterised with transmission electron Microscopy, X-ray photoelectron spectroscopy, Fourier-transform infrared spectroscopy and Circular dichroism spectroscopy. Biochemical characterisation of immobilised enzyme showed broader pH and thermal optima compared to soluble form. Reusability of the immobilised enzyme for hydrolysis of long chain esters was demonstrated up to ten cycles.Conclusion/significanceLipase immobilised on MWNTs has exhibited significantly improved thermal stability. The exploration of advanced nanomaterial for enzyme immobilisation support using sophisticated techniques makes nanobiocatalyst of potential interest for biosensor applications.

| S-EPMC3772012 | biostudies-literature

Sorting centimetre-long single-walled carbon nanotubes.

Project description:While several approaches have been developed for sorting metallic (m) or semiconducting (s) single-walled carbon nanotubes (SWCNTs), the length of SWCNTs is limited within a micrometer, which restricts excellent electrical performances of SWCNTs for macro-scale applications. Here, we demonstrate a simple sorting method of centimetre-long aligned m- and s-SWCNTs. Ni particles were selectively and uniformly coated along the 1-cm-long m-SWCNTs by applying positive gate bias during electrochemical deposition with continuous electrolyte injection. To sort s-SWCNTs, the Ni coating was oxidized to form insulator outer for blocking of current flow through inner m-SWCNTs. Sorting of m-SWCNTs were demonstrated by selective etching of s-SWCNTs via oxygen plasma, while the protected m-SWCNTs by Ni coating remained intact. The series of source-drain pairs were patterned along the 1-cm-long sorted SWCNTs, which confirmed high on/off ratio of 10(4)-10(8) for s-SWCNTs and nearly 1 for m-SWCNTs.

| S-EPMC4967858 | biostudies-literature

Functionalization of Single-Walled Carbon Nanotubes with End-Capped Polystyrene via a Single-Step Diels-Alder Cycloaddition.

Project description:A facile, single-step, [4+2] Diels-Alder cycloaddition reaction for the surface functionalization of single-walled carbon nanotubes (SWNTs) with end-capped polystyrene chains is presented. The thermal cycloaddition reaction took place at high temperature (~230 °C) without any catalyst between the sp2 network of carbon nanotubes, which acted as dienophile, and the diphenylethylene cyclobutene (DPE-CB) terminal group of the polystyrene chain. Anionic polymerization was employed for the synthesis of the polystyrene macromolecule, and successful and quantitative end-capping reaction with the DPE-CB molecule was confirmed by matrix-assisted laser desorption/ionization time of flight mass spectroscopy. Thermogravimetric analysis revealed the wt % of the grafted macromolecule on the CNT surface as well as the grafting density of the polymer chains on the SWNTs (0.027 chains nm-2). Direct evidence for the surface functionalization and the presence of thin polystyrene film was obtained by transmission electron microscopy (TEM) and by atomic force microscopy (AFM).

| S-EPMC8038725 | biostudies-literature

Pillar[5]arene-Decorated Single-Walled Carbon Nanotubes.

Project description:Control of single-walled carbon nanotube dispersion properties is of substantial interest to the scientific community. In this work, we sought to investigate the effect of a macrocycle, pillar[5]arene, on the dispersion properties of a polymer-nanotube complex. Pillar[5]arenes are a class of electron-rich macrocyclic hosts capable of forming inclusion complexes with electron-poor guests, such as alkyl nitriles. A hydroxyl-functionalized pillar[5]arene derivative was coupled to the alkyl bromide side chains of a polyfluorene, which was then used to coat the surface of single-walled carbon nanotubes. Noncovalent functionalization of carbon nanotubes with the macrocycle-containing conjugated polymer significantly enhanced nanotube solubility, resulting in dark and concentrated nanotube dispersions (600 ?g mL-1), as evidenced by UV-vis-NIR spectroscopy and thermogravimetric analysis. Differentiation of semiconducting and metallic single-walled carbon nanotube species was analyzed by a combination of UV-vis-NIR, Raman, and fluorescence spectroscopy. Raman spectroscopy confirmed that the concentrated nanotube dispersion produced by the macrocycle-containing polymer was due to well-exfoliated nanotubes, rather than bundle formation. The polymer-nanotube dispersion was investigated using 1H NMR spectroscopy, and it was found that host-guest chemistry between pillar[5]arene and 1,6-dicyanohexane occurred in the presence of the polymer-nanotube complex. Utilizing the host-guest capability of pillar[5]arene, the polymer-nanotube complex was incorporated into a supramolecular organogel.

| S-EPMC6645158 | biostudies-literature

Single Walled BiI<sub>3</sub> Nanotubes Encapsulated within Carbon Nanotubes.

Project description:Inorganic nanotubes are morphological counterparts of carbon nanotubes (CNTs). Yet, only graphene-like BN layer has been readily organized into single walled nanotubes so far. In this study, we present a simple route to obtain inorganic single walled nanotubes - a novel ultrathin morphology for bismuth iodide (BiI3), embedded within CNTs. The synthesis involves the capillary filling of BiI3 into CNT, which acts as a nanotemplate, by annealing the BiI3-CNT mixture above the melting point of BiI3. Aberration corrected scanning/transmission electron microscopy is used in characterizing the novel morphology of BiI3. A critical diameter which enables the formation of BiI3 nanotubes, against BiI3 nanorods is identified. The relative stability of these phases is investigated with the density functional theory calculations. Remarkably, the calculations reveal that the single walled BiI3 nanotubes are semiconductors with a direct band gap, which remain stable even without the host CNTs.

| S-EPMC6031677 | biostudies-literature

Carboxylated short single-walled carbon nanotubes but not plain and multi-walled short carbon nanotubes show in vitro genotoxicity.

Project description:Long carbon nanotubes (CNTs) resemble asbestos fibers due to their high length to diameter ratio and they thus have genotoxic effects. Another parameter that might explain their genotoxic effects is contamination with heavy metal ions. On the other hand, short (1-2 µm) CNTs do not resemble asbestos fibers, and, once purified from contaminations, they might be suitable for medical applications. To identify the role of fiber thickness and surface properties on genotoxicity, well-characterized short pristine and carboxylated single-walled (SCNTs) and multi-walled (MCNTs) CNTs of different diameters were studied for cytotoxicity, the cell's response to oxidative stress (immunoreactivity against hemoxygenase 1 and glutathione levels), and in a hypoxanthine guanine phosphoribosyltransferase (HPRT) assay using V79 chinese hamster fibroblasts and human lung adenocarcinoma A549 cells. DNA repair was demonstrated by measuring immunoreactivity against activated histone H2AX protein. The number of micronuclei as well as the number of multinucleated cells was determined. CNTs acted more cytotoxic in V79 than in A549 cells. Plain and carboxylated thin (<8 nm) SCNTs and MCNTs showed greater cytotoxic potential and carboxylated CNTs showed indication for generating oxidative stress. Multi-walled CNTs did not cause HPRT mutation, micronucleus formation, DNA damage, interference with cell division, and oxidative stress. Carboxylated, but not plain, SCNTs showed indication for in vitro DNA damage according to increase of H2AX-immunoreactive cells and HPRT mutation. Although short CNTs presented a low in vitro genotoxicity, functionalization of short SCNTs can render these particles genotoxic.

| S-EPMC4434219 | biostudies-literature

Translocation of single-stranded DNA through single-walled carbon nanotubes.

Project description:We report the fabrication of devices in which one single-walled carbon nanotube spans a barrier between two fluid reservoirs, enabling direct electrical measurement of ion transport through the tube. A fraction of the tubes pass anomalously high ionic currents. Electrophoretic transport of small single-stranded DNA oligomers through these tubes is marked by large transient increases in ion current and was confirmed by polymerase chain reaction analysis. Each current pulse contains about 10(7) charges, an enormous amplification of the translocated charge. Carbon nanotubes simplify the construction of nanopores, permit new types of electrical measurements, and may open avenues for control of DNA translocation.

| S-EPMC2801077 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data