Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

MoO3 Thickness, Thermal Annealing and Solvent Annealing Effects on Inverted and Direct Polymer Photovoltaic Solar Cells

ABSTRACT: Several parameters of the fabrication process of inverted polymer bulk heterojunction solar cells based on titanium oxide as an electron selective layer and molybdenum oxide as a hole selective layer were tested in order to achieve efficient organic photovoltaic solar cells. Thermal annealing treatment is a common process to achieve optimum morphology, but it proved to be damageable for the performance of this kind of inverted solar cells. We demonstrate using Auger analysis combined with argon etching that diffusion of species occurs from the MoO3/Ag top layers into the active layer upon thermal annealing. In order to achieve efficient devices, the morphology of the bulk heterojunction was then manipulated using the solvent annealing technique as an alternative to thermal annealing. The influence of the MoO3 thickness was studied on inverted, as well as direct, structure. It appeared that only 1 nm-thick MoO3 is enough to exhibit highly efficient devices (PCE = 3.8%) and that increasing the thickness up to 15 nm does not change the device performance.

SUBMITTER: Chambon S

PROVIDER: S-EPMC5449054 | biostudies-literature | 2012 Nov

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Effects of fluorination and thermal annealing on charge recombination processes in polymer bulk-heterojunction solar cells.

Project description:We investigate the effect of fluorination on the photovoltaic properties of an alternating conjugated polymer composed of 4,8-di-2-thienylbenzo[1,2-b:4,5-b']dithiophene (BDT) and 4,7-bis([2,2'-bithiophen]-5-yl)-benzo-2-1-3-thiadiazole (4TBT) units in bulk-heterojunction solar cells. The unsubstituted and fluorinated polymers afford very similar open-circuit voltages and fill factor values, but the fluorinated polymer performed better due to enhanced aggregation which provides a higher photocurrent. The photovoltaic performance of both materials improved upon thermal annealing at 150-200 °C as a result of a significantly increased fill factor and open-circuit voltage, counteracted by a slight loss in photocurrent. Detailed studies of the morphology, light intensity dependence, external quantum efficiency and electroluminescence allowed the exploration of the effects of fluorination and thermal annealing on the charge recombination and the nature of the donor-acceptor interfacial charge transfer states in these films.

| S-EPMC6333271 | biostudies-literature

The Effect of Solvent Vapor Annealing on Drug-Loaded Electrospun Polymer Fibers.

Project description:Electrospinning has emerged as a powerful strategy to develop controlled release drug delivery systems but the effects of post-fabrication solvent vapor annealing on drug-loaded electrospun fibers have not been explored to date. In this work, electrospun poly(ԑ-caprolactone) (PCL) fibers loaded with the hydrophobic small-molecule spironolactone (SPL) were explored. Immediately after fabrication, the fibers are smooth and cylindrical. However, during storage the PCL crystallinity in the fibers is observed to increase, demonstrating a lack of stability. When freshly-prepared fibers are annealed with acetone vapor, the amorphous PCL chains recrystallize, resulting in the fiber surfaces becoming wrinkled and yielding shish-kebab like structures. This effect does not arise after the fibers have been aged. SPL is found to be amorphously dispersed in the PCL matrix both immediately after electrospinning and after annealing. In vitro dissolution studies revealed that while the fresh fibers show a rapid burst of SPL release, after annealing more extended release profiles are observed. Both the rate and extent of release can be varied through changing the annealing time. Further, the annealed formulations are shown to be stable upon storage.

| S-EPMC7076406 | biostudies-literature

Optimizing Polymer Solar Cells Using Non-Halogenated Solvent Blends.

Project description:More environmentally friendly polymer solar cells were constructed using a conjugated polymer, poly (2,5-thiophene-alt-4,9-bis(2-hexyldecyl)-4,9-dihydrodithieno[3,2-c:3',2'h][1,5] naphthyridine-5,10-dione, PTNT, as a donor material in combination with PC71BM as an acceptor in a bulk heterojunction device structure. A non-halogenated processing solvent (o-xylene) and solvent additives that are less harmful to the environment such as 1-methoxynaphthalene (MN) and 1-phenylnaphthalene (PN) were used throughout the study as processing solvents. The most widely used halogenated solvent additives (1,8-diiodooctane (DIO) and 1-chloronaphthalene (CN)) were also used for comparison and to understand the effect of the type of solvent additives on the photovoltaic performances. Atomic force microscopy (AFM) was employed to investigate the surface morphology of the films prepared in the presence of the various additives. The best-performing polymer solar cells provided a high open-circuit voltage of 0.9 V, an efficient fill factor of around 70%, and a highest power conversion efficiency (PCE) of over 6% with the use of the eco-friendlier o-xylene/MN solvent systems. Interestingly, the solvent blend which is less harmful and with low environmental impact gave a 20% rise in PCE as compared to an earlier reported device efficiency that was processed from the chlorinated solvent o-dichlorobenzene (o-DCB).

| S-EPMC6473778 | biostudies-literature

Optical-Based Thickness Measurement of MoO3 Nanosheets.

Project description:Considering that two-dimensional (2D) molybdenum trioxide has acquired more attention in the last few years, it is relevant to speed up thickness identification of this material. We provide two fast and non-destructive methods to evaluate the thickness of MoO3 flakes on SiO2/Si substrates. First, by means of quantitative analysis of the apparent color of the flakes in optical microscopy images, one can make a first approximation of the thickness with an uncertainty of ±3 nm. The second method is based on the fit of optical contrast spectra, acquired with micro-reflectance measurements, to a Fresnel law-based model that provides an accurate measurement of the flake thickness with ±2 nm of uncertainty.

| S-EPMC7407517 | biostudies-literature

Robust perovskite formation via vacuum thermal annealing for indoor perovskite solar cells.

Project description:Perovskite materials are fascinating candidates for the next-generation solar devices. With long charge carrier lifetime, metal-halide perovskites are known to be good candidates for low-light harvesting. To match the irradiance spectra of indoor light, we configured a triple-cation perovskite material with appropriate content of bromide and chloride (FA0.45MA0.49Cs0.06Pb(I0.62Br0.32Cl0.06)3) to achieve an optimum band gap (Eg) of [Formula: see text]1.80 eV. With low photon flux at indoor condition, minimal recombination is highly desirable. To achieve such goal, we, for the first time, combined dual usage of antisolvent deposition and vacuum thermal annealing, namely VTA, to fabricate a high-quality perovskite film. VTA leads to compact, dense, and hard morphology while suppressing trap states at surfaces and grain boundaries, which are key culprits for exciton losses. With low-cost carbon electrode architecture, VTA devices exhibited average power conversion efficiency (PCE) of 27.7 ± 2.7% with peak PCE of 32.0% (Shockley-Queisser limit of 50-60%) and average open-circuit voltage (Voc) of 0.93 ± 0.02 V with peak Voc of 0.96 V, significantly more than those of control and the vacuum treatment prior to heat.

| S-EPMC10325999 | biostudies-literature

High-Throughput Screening of Blade-Coated Polymer:Polymer Solar Cells: Solvent Determines Achievable Performance.

Project description:Optimization of a new system for organic solar cells is a multiparametric analysis problem that requires substantial efforts in terms of time and resources. The strong microstructure-dependent performance of polymer:polymer cells makes them particularly difficult to optimize, or to translate previous knowledge from spin coating into more scalable techniques. In this work, the photovoltaic performance of blade-coated devices was studied based on the promising polymer:polymer system PBDB-T and PF5-Y5 as donor and acceptor, respectively. Using the recently developed high-throughput methodology, the system was optimized for multiple variables, including solvent system, active layer composition, ratio, and thickness, among others, by fabricating more than 500 devices with less than 24 mg of each component. As a result, the power conversion efficiency of the blade-coated devices varied from 0.08 to 6.43 % in the best device. The performed statistical analysis of the large experimental data obtained showed that solvent selection had the major impact on the final device performance due to its influence on the active layer microstructure. As a conclusion, the use of the plot of the device efficiency in the Hansen space was proposed as a powerful tool to guide solvent selection in organic photovoltaics.

| S-EPMC9305181 | biostudies-literature

Nanofluid Development Using Silver Nanoparticles and Organic-Luminescent Molecules for Solar-Thermal and Hybrid Photovoltaic-Thermal Applications.

Project description:Exploiting solar energy using photo-thermal (PT) and/or hybridised photovoltaic/thermal (PVT) systems can represent a viable alternative to the growing demand for renewable energy. For large-scale implementation, such systems require thermal fluids able to enhance the combined conversion efficiency achievable by controlling the 'thermal' and 'electrical' components of the solar spectrum. Nanofluids are typically employed for these purposes and they should exhibit high heat-transfer capabilities and optical properties tuned towards the peak performance spectral window of the photovoltaic (PV) component. In this work, novel nanofluids, composed of highly luminescent organic molecules and Ag nanoparticles dispersed within a base fluid, were tested for PT and PVT applications. These nanofluids were designed to mimic the behaviour of luminescent down-shifting molecules while offering enhanced thermo-physical characteristics over the host base fluid. The nanofluids' conversion efficiency was evaluated under a standard AM1.5G weighted solar spectrum. The results revealed that the Ag nanoparticles' inclusion in the composite fluid has the potential to improve the total solar energy conversion. The nanoparticles' presence minimizes the losses in the electrical power component of the PVT systems as the thermal conversion increases. The enhanced performances recorded suggest that these nanofluids could represent suitable candidates for solar energy conversion applications.

| S-EPMC7353118 | biostudies-literature

Thickness dependence of the MoO(3) blocking layers on ZnO nanorod-inverted organic photovoltaic devices.

Project description:Organic solar cells based on vertically aligned zinc oxide nanorod arrays (ZNR) in an inverted structure of indium tin oxide (ITO)∕ZNR∕poly(3-hexylthiophene): (6,6)-phenyl C61 butyric acid methyl ester(P3HT:PCBM)∕MoO(3)∕aluminum(Al) were studied. We found that the optimum MoO(3) layer thickness condition of 20 nm, the MoO(3) can effectively decrease the probability of bimolecular recombination either at the Al interface or within the active layer itself. For this optimum condition we get a power conversion efficiency of 2.15%, a short-circuit current density of 9.02 mA∕cm(2), an open-circuit voltage of 0.55V, and a fill factor of 0.44 under 100 mW∕cm(2) irradiation. Our investigations also show that the highly crystallized ZNR can create short and continuous pathways for electron transport and increase the contact area between the ZNR and the organic materials.

| S-EPMC3069983 | biostudies-other

Improving the photovoltaic performance of planar heterojunction perovskite solar cells by mixed solvent vapor treatment.

Project description:The grain size of perovskite films is a key factor to optimize the performance of perovskite photovoltaic devices. Herein, a new route is developed in this paper to prepare CH3NH3PbI3 (MAPbI3) films with a better morphology and crystallization. This method includes the spin coating deposition of perovskite films with a precursor solution of PbI2 and CH3NH3I at the molar ratio 1 : 1 and thermal annealing (TA). The thermal annealing is conducted with a thermal-induced process to realize grain growth with solvent evaporation. In addition, a mixed solvent vapor treatment in acetic acid with chlorobenzene (HAc/CB) improves the morphology and crystallization of films further. As a result, the photovoltaic device based on the perovskite film treated by mixed HAc/CB solvent exhibits the best efficiency of 13.15% in comparison to the control device with 11.44% under AM 1.5G irradiation (100 mW cm-2).

| S-EPMC9079065 | biostudies-literature

Morphological, Chemical, and Electronic Changes of the Conjugated Polymer PTB7 with Thermal Annealing.

Project description:There is considerable interest in improving the performance of organic optoelectronic devices through processing techniques. Here, we study the effect of high-temperature annealing on the properties of the semiconducting polymer PTB7 and PTB7:fullerene blends, of interest as efficient organic photovoltaic (OPV) devices. Annealing to moderate temperature improves the PTB7 morphology and optoelectronic properties. High-temperature annealing also improves morphology but results in poorer optoelectronic properties. This is a result of side chain cleavage that creates by-products that act as trap states, increasing electronic disorder and decreasing mobility. We further observe changes to the PTB7 chemical structure after thermal cleavage that are similar to those following solar irradiation. This implies that side chain cleavage is an important mechanism in device photodegradation, which is a major "burn-in" loss mechanism in OPV. These results lend insight into side chain cleavage as a method of improving optoelectronic properties and suggest strategies for improvement in device photostability.

| S-EPMC6135925 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data