Droplet Velocity in an Electrowetting on Dielectric Digital Microfluidic Device.
Ontology highlight
ABSTRACT:
SUBMITTER: Nahar MM
PROVIDER: S-EPMC6189997 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Current human fertilization in vitro (IVF) bypasses the female oviduct and manually inseminates, fertilizes and cultivates embryos in a static microdrop containing appropriate chemical compounds. A microfluidic microchannel system for IVF is considered to provide an improved in-vivo-mimicking environment to enhance the development in a culture system for an embryo before implantation. We demonstrate a novel digitalized microfluidic device powered with electrowetting on a dielectric (EWOD) to culture an embryo in vitro in a single droplet in a microfluidic environment to mimic the environment in vivo for development of the embryo and to culture the embryos with good development and live births. Our results show that the dynamic culture powered with EWOD can manipulate a single droplet containing one mouse embryo and culture to the blastocyst stage. The rate of embryo cleavage to a hatching blastocyst with a dynamic culture is significantly greater than that with a traditional static culture (p<0.05). The EWOD chip enhances the culture of mouse embryos in a dynamic environment. To test the reproductive outcome of the embryos collected from an EWOD chip as a culture system, we transferred embryos to pseudo-pregnant female mice and produced live births. These results demonstrate that an EWOD-based microfluidic device is capable of culturing mammalian embryos in a microfluidic biological manner, presaging future clinical application.
| S-EPMC4416819 | biostudies-literature
Project description:In order to get rid of the dependence on expensive photolithography technology and related facilities, an economic and simple design and fabrication technology for digital microfluidics (DMF) is proposed. The electrodes pattern was generated by inkjet printing nanosilver conductive ink on the flexible Polyethylene terephthalate (PET) substrate with a 3D circuit board printer, food wrap film was attached to the electrode array to act as the dielectric layer and Teflon® AF was sprayed to form a hydrophobic layer. The PET substrate and food wrap film are low cost and accessible to general users. The proposed flexible DMF chips can be reused for a long time by replacing the dielectric film coated with hydrophobic layer. The resolution and conductivity of silver traces and the contact angle and velocity of the droplets were evaluated to demonstrate that the proposed technology is comparable to the traditional DMF fabrication process. As far as the rapid prototyping of DMF is concerned, this technology has shown very attractive advantages in many aspects, such as fabrication cost, fabrication time, material selection and mass production capacity, without sacrificing the performance of DMF. The flexible DMF chips have successfully implemented basic droplet operations on a square and hexagon electrode array.
| S-EPMC7765594 | biostudies-literature
Project description:Access to diverse PET tracers for preclinical and clinical research remains a major obstacle to research in cancer and other disease research. The prohibitive cost and limited availability of tracers could be alleviated by microfluidic radiosynthesis technologies combined with a high-yield microscale radiosynthetic method. In this report, we demonstrate the multistep synthesis of 3'-deoxy-3'-(18)F-fluorothymidine ((18)F-FLT) with high yield on an electrowetting-on-dielectric (EWOD) microfluidic radiosynthesizer, previously developed in our group. We have identified and established several parameters that are most critical in the microscale radiosynthesis, such as the reaction time, reagent concentration, and molar ratios, to successfully synthesize (18)F-FLT in this compact platform.(18)F-FLT was synthesized from the 3-N-Boc-1-[5-O-(4,4'-dimethoxytrityl)-3-O-nosyl-2-deoxy-?-D-lyxofuranosyl] thymine precursor on the EWOD chip starting from the first solvent exchange and (18)F-fluoride ion activation step to the final deprotection step. The fluorination reaction was performed in a mixture of thexyl alcohol and dimethyl sulfoxide. The crude product after deprotection was collected from the chip and purified on a custom-made solid-phase extraction cartridge and subjected to quality control testing. The purified (18)F-FLT was suitable for small-animal PET studies in multiple nude mice xenografted with the A431 carcinoma cell line.(18)F-FLT was successfully synthesized on the EWOD microdevice coupled with an off-chip solid-phase extraction purification with a decayed-corrected radiochemical yield of 63% ± 5% (n = 5) and passed all of the quality control tests required by the U.S. Pharmacopeia for radiotracers to be injected into humans. We have successfully demonstrated the synthesis of several batches of (18)F-FLT on EWOD, starting with approximately 333 MBq of radioactivity and obtained up to 52 MBq (non-decay-corrected) of (18)F-FLT on cartridge purification. The specific activity of 2 representative preparations of (18)F-FLT synthesized on the EWOD chip were measured to be 1,800 and 2,400 GBq/?mol.The EWOD microchip and optimized synthesis method in combination represent an effective platform for synthesizing (18)F-FLT with high yield and of good quality for imaging. This compact platform, with configurable synthesis steps, could potentially form the basis of a stand-alone system that decouples PET probe production from the cyclotron and specialized radiochemistry facilities and increases diversity and flexibility in probe production.
| S-EPMC4494735 | biostudies-literature
Project description:Localized heating of droplets on an electrowetting-on-dielectric (EWOD) chip has been implemented and shown to accelerate trypsin digestion reaction rates, sample drying, and matrix crystallization for matrix-assisted laser desorption ionization mass spectrometry (MALDI-MS). Achieving this involved extending the functionality of previous EWOD droplet-based techniques by developing a multifunctional electrode with closed-loop temperature control, while minimizing overall system complexity and addressing challenges associated with rapid evaporation. For the EWOD chip design, we discuss the performance of multifunctional surface electrodes for actuation, localized Joule heating, and thermistic temperature sensing. Furthermore, a hydrophilic pattern is formed in the multifunctional electrode to control the location of an evaporating droplet on the electrode. To demonstrate the capabilities and limitations of this technique, we performed three experiments and measured the results using MALDI-MS: (i) insulin disulfide reductions in dithiothreitol (DTT) over a range of heater temperatures (22-70 °C) to show how reaction rates can be affected by thermal control, (ii) insulin disulfide reductions at 130 °C in dimethyl sulfoxide (DMSO) to demonstrate a reaction in a high boiling point solvent, and (iii) tryptic digestions of cytochrome c at 22 and 40 °C to show that heated droplets can yield reasonably higher peptide sequence coverage than unheated droplets. Although they do not decouple the effects of changing temperatures and concentrations, these experiments verified that thermal cycling by EWOD electrodes accelerates reaction rates in liquid droplets in air.
| S-EPMC2998283 | biostudies-literature
Project description:Picoliter droplets actuated on an electrowetting-on-dielectric (EWD) actuator are demonstrated. In this study, the physical scaling of electrodes for 33 μm and 21 μm EWD devices resulted in droplets of 12 pl and 5 pl being dispensed respectively in conjunction with 3 μm SU8 gaskets. The stacked multi-layer insulators in the actuators consisted of 200 nm tantalum pentoxide (Ta2O5) and 200 nm parylene C films deposited and coated with 70 nm of CYTOP. The voltages for dispensing droplets on chips without any external pressure sources are 17.1 Vrms and 22 Vrms for these two sets of devices. A 12 pl droplet can be split into two 6 pl daughter droplets at 18.7 Vrms with 33 μm electrode devices. Droplet manipulation is also demonstrated with paramagnetic beads and buffer solutions with proteins. In addition, electrodes with interlocking protrusions and special featured reservoir gasket are designed to facilitate droplet dispensing on these scaled EWD devices. In order to improve sealing of the two-piece sandwich EWD structure, a soft material, Norland Optical Adhesive (NOA), was coated on the top plate along with pressure on top. We demonstrate that based on fundamental theories and experiments, the dimensional scaling of EWD devices has not yet met a limitation as long as the EWD device can be sealed well.
| S-EPMC3613134 | biostudies-literature
Project description:One of the major hurdles in the development of biocompatible/biodegradable EWOD (Electrowetting-on-dielectric) devices is the biocompatibility of the dielectric and hydrophobic layers. In this study, we address this problem by using reactive ion etching (RIE) to prepare a super-hydrophobic film combining fluorinated cellulose triacetate (CTA) and poly (lactic-co-glycolic acid) (PLGA). The contact angle (CA) of water droplets on the proposed material is about 160°. X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) characterizations indicate that a slight increase in the surface roughness and the formation of CFx (C-F or CF?) bonds are responsible for the super-hydrophobic nature of the film. Alternating Current (AC) static electrowetting and droplet transportation experiments evidence that contact angle hysteresis and contact line pinning are greatly reduced by impregnating the CTA/PLGA film with silicon oil. Therefore, this improved film could provide a biocompatible alternative to the typical Teflon® or Cytop® films as a dielectric and hydrophobic layer.
| S-EPMC6120052 | biostudies-literature
Project description:The rapid detection of pollutants in water can be performed with enzymatic probes, the catalytic light-emitting activity of which decreases in the presence of many types of pollutants. Herein, we present a microfluidic system for continuous chemoenzymatic biosensing that generates emulsion droplets containing two enzymes of the bacterial bioluminescent system (luciferase and NAD(P)H:FMN-oxidoreductase) with substrates required for the reaction. The developed chip generates "water-in-oil" emulsion droplets with a volume of 0.1 μL and a frequency of up to 12 drops per minute as well as provides the efficient mixing of reagents in droplets and their distancing. The bioluminescent signal from each individual droplet was measured by a photomultiplier tube with a signal-to-noise ratio of up to 3000/1. The intensity of the luminescence depended on the concentration of the copper sulfate with the limit of its detection of 5 μM. It was shown that bioluminescent enzymatic reactions could be carried out in droplet reactors in dispersed streams. The parameters and limitations required for the bioluminescent reaction to proceed were also studied. Hereby, chemoenzymatic sensing capabilities powered by a droplet microfluidics manipulation technique may serve as the basis for early-warning online water pollution systems.
| S-EPMC9325247 | biostudies-literature
Project description:Methodological advances in on-chip technology enable high-throughput drug screening, such as droplet-array sandwiching technology. Droplet-array sandwiching technology involves upper and lower substrates with a droplet-array designed for a one-step process. This technology is, however, limited to batch manipulation of the droplet-array. Here, we propose a method for selective control of individual droplets, which allows different conditions for individual droplet pairs. Electrowetting-on-dielectric (EWOD) technology is introduced to control the height of the droplets so that the contact between droplet-pairs can be individually controlled. Circular patterns 4 mm in diameter composed of electrodes for EWOD and hydrophilic-hydrophobic patterns for droplet formation 4 μl in volume were developed. We demonstrate the selective control of the droplet height by EWOD for an applied voltage up to 160 V and selective control of the contact and transport of substances. Presented results will provide useful method for advanced drug screening, including cell-based screening.
| S-EPMC8196194 | biostudies-literature
Project description:Controlling droplet sizes is one of the most important aspects of droplet generators used in biomedical research, drug discovery, high-throughput screening, and emulsion manufacturing applications. This is usually achieved by using multiple devices that are restricted in their range of generated droplet sizes. In this paper, a co-flow microfluidic droplet-generation device with flexible walls was developed such that the width of the continuous (C)-phase channel around the dispersed (D)-phase droplet-generating needle can be adjusted on demand. This actuation mechanism allowed for the adjustment of the C-phase flow velocity, hence providing modulated viscous forces to manipulate droplet sizes in a single device. Two distinct droplet-generation regimes were observed at low D-phase Weber numbers, i.e., a dripping regime at high- and medium-channel widths and a plug regime at low-channel widths. The effect of channel width on droplet size was investigated in the dripping regime under three modes of constant C-phase flow rate, velocity, and Capillary number. Reducing the channel width at a constant C-phase flow rate had the most pronounced effect on producing smaller droplets. This effect can be attributed to the combined influences of the wall effect and increased C-phase velocity, leading to a greater impact on droplet size due to the intensified viscous force. Droplet sizes in the range of 175-913 µm were generated; this range was ~2.5 times wider than the state of the art, notably using a single microfluidic device. Lastly, an empirical model based on Buckingham's Pi theorem was developed to predict the size of droplets based on channel width and height as well as the C-phase Capillary and Reynolds numbers.
| S-EPMC10536617 | biostudies-literature
Project description:Handling the aqueous two-phase systems (ATPSs) formed by liquid-liquid phase separation (LLPS) relies on the accurate construction of binodal curves and tie-lines, which delineate the polymer concentrations required for phase separation and depict the properties of the resulting phases, respectively. Various techniques to determine the binodal curves and tie-lines of ATPSs exist, but most rely on manually pipetting relatively large volumes of fluids in a slow and tedious manner. We describe a method to determine ATPS binodals and tie-lines that overcomes these disadvantages: microscale droplet manipulation by electrowetting-on-dielectric (EWOD). EWOD enables automated handling of droplets in an optically transparent platform that allows for in situ droplet observation. Separated phases are clearly visible, and the volumes of each phase are readily determined. Additionally, in considering the molecular crowding present in living cells, this work examines the role of a macromolecule in prompting LLPS. These results show that EWOD-driven droplet manipulation effectively interrogates the phase dynamics of ATPSs and macromolecular crowding in LLPS.
| S-EPMC6452887 | biostudies-literature