The Role of Thickness Control and Interface Modification in Assembling Efficient Planar Perovskite Solar Cells.
Ontology highlight
ABSTRACT: Perovskite solar cells (PSCs) have achieved tremendous success within just a decade. This success is critically dependent upon compositional engineering, morphology control of perovskite layer, or contingent upon high-temperature annealed mesoporous TiO2, but quantitative analysis of the role of facile TiCl4 treatment and thickness control of the compact TiO2 layer has not been satisfactorily undertaken. Herein, we report the facile thickness control and post-treatment of the electron transport TiO2 layer to produce highly efficient planar PSCs. TiCl4 treatment of TiO2 layer could remove the surface trap and decrease the charge recombination in the prepared solar cells. Introduction of ethanol into the TiCl4 aqueous solution led to further improved open-circuit voltage and short-circuit current density of the related devices, thus giving rise to enhanced power conversion efficiency (PCE). After the optimal TiCl4 treatment, PCE of 16.42% was achieved for PSCs with TiCl4 aqueous solution-treated TiO2 and 19.24% for PSCs with TiCl4 aqueous/ethanol solution-treated TiO2, respectively. This work sheds light on the promising potential of simple planar PSCs without complicated compositional engineering and avoiding the deposition and optimization of the mesoporous scaffold layer.
Project description:Organic-inorganic halide perovskite solar cells (PSCs) have drawn tremendous attention owing to their remarkable photovoltaic performance and simple preparation process. However, conventional wet-chemical synthesis methods inevitably create defects both in the bulk and at the interfaces of perovskites, leading to recombination of charge carriers and reduced stability. Herein, a bilateral interface modification to perovskites by doping room-temperature synthesized CsPbBr3 nanocrystals (CN) is reported. The ultrafast transient absorption measurement reveals that CN effectively suppresses the defect at the SnO2 /perovskite interface and boosts the interfacial electron transport. Meanwhile, the in situ Kelvin probe force microscopy and contact potential difference characterizations verify that the CN within the upper part of the perovskites enhances the built-in electric field, facilitating oriented migration of the carriers within the perovskite. Combining the superiorities of CN modifiers on both sides, the bilaterally modified CH3 NH3 PbI3 -based planar PSCs exhibit optimal power conversion efficiency exceeding 20% and improved device stability.
Project description:Compact TiO2 films are one of the most widely used electron transport layers (ETLs) in planar perovskite solar cells (PSCs). However, the performance of the PSC device is controlled by the comprehensive qualities of the functional layers and their bilateral surfaces. In this work, the alkali metal halide of RbBr as the interfacial modifier is introduced into the interface of the TiO2 ETL and perovskite absorber. By spin-coating the proper content of RbBr, the surface of the TiO2 film consisting of smooth morphology and low density of oxygen-deficiency defect is readily obtained. The perovskite layer successively fabricated on the RbBr-modified TiO2 film demonstrates large grain size, low surface roughness, and low bulk defect density, which enhances the electron extraction and decreases nonradiation recombination. By virtue of the modulation of the perovskite crystal quality and the passivation of the interfacial defects, the light-harvesting efficiency of the corresponding device is increased to 21.15 from 19.21% for the PSC without a RbBr insertion layer. More importantly, the passivation strategy enables impressive device stability by retaining 90% of its initial efficiency in an ambient environment for 500 h. This study provides a promising and feasible strategy to regulate surface passivation engineering and simultaneously facilitate the perovskite crystal growth for the achievement of efficient and stable perovskite photovoltaics.
Project description:For the further improvement of the power conversion efficiency (PCE) and stability of perovskite solar cells (PSCs), the buried interface between the perovskite and the electron transport layer is crucial. However, it is challenging to effectively optimize this interface as it is buried beneath the perovskite film. Herein, we have designed and synthesized a series of multifunctional organic-inorganic (OI) complexes as buried interfacial material to promote electron extraction, as well as the crystal growth of the perovskite. The OI complex with BF4- group not only eliminates oxygen vacancies on the SnO2 surface but also balances energy level alignment between SnO2 and perovskite, providing a favorable environment for charge carrier extraction. Moreover, OI complex with amine (- NH2) functional group can regulate the crystallization of the perovskite film via interaction with PbI2, resulting in highly crystallized perovskite film with large grains and low defect density. Consequently, with rational molecular design, the PSCs with optimal OI complex buried interface layer which contains both BF4- and -NH2 functional groups yield a champion device efficiency of 23.69%. More importantly, the resulting unencapsulated device performs excellent ambient stability, maintaining over 90% of its initial efficiency after 2000 h storage, and excellent light stability of 91.5% remaining PCE in the maximum power point tracking measurement (under continuous 100 mW cm-2 light illumination in N2 atmosphere) after 500 h.
Project description:Ga-doped ZnO (GZO)-graded layer, facilitating electron extraction from electron transport layer, was integrated on the surface of transparent indium tin oxide (ITO) cathode by using graded sputtering technique to improve the performance of planar n-i-p perovskite solar cells (PSCs). The thickness of graded GZO layer was controlled to optimize GZO-indium tin oxide (ITO) combined electrode for planar n-i-p PSCs. At optimized graded thickness of 15 nm, the GZO-ITO combined electrode showed an optical transmittance of 95%, a resistivity of 2.3 × 10-4 Ohm cm, a sheet resistance of 15.6 Ohm/square, and work function of 4.23 eV, which is well matched with the 4.0-eV lowest unoccupied molecular orbital of [6,6]-phenyl-C61-butyric acid methyl ester. Owing to enhanced extraction of electron by the graded GZO, the n-i-p PSC with GZO-ITO combined electrode showed higher power conversion efficiency (PCE) of 9.67% than the PCE (5.25%) of PSC with only ITO electrode without GZO-graded layer. In addition, the GZO integrated-ITO electrode acts as transparent electrode and electron extraction layer simultaneously due to graded mixing of the GZO at the surface region of ITO electrode.
Project description:Large-size organic halide passivation has been considered an efficient approach to enhance the perovskite solar cell (PSC) efficiency and stability. Herein, a facile posttreatment strategy was demonstrated, wherein trifluoromethyl-phenethylamine hydrobromide (CF3-PEABr) is firstly used to passivate the perovskite film surface. The CF3-PEABr surface posttreatment could coordinate with halide dangling bonds that exist at the perovskite crystal surface. Moreover, the surface treatment with CF3-PEABr could efficiently passivate the defects in the perovskite film and suppress the nonradiative carrier recombination. As a result, a high efficiency of 21.3% is obtained, and an increment of 80 mV in V oc (a large V oc of 1.15 V, with a 0.42 V voltage deficit) occurs, compared to the control device. To relieve the hydrophobic nature properties of the -CF3 functional group and the dewetting problem of PCBM layer deposition, a surfactant Triton X-100 is used to modify the PCBM layer. Furthermore, the devices with CF3-PEABr posttreatment exhibit better operational, thermal (85°C), and long storage stabilities without any encapsulation.
Project description:Indium thin oxide (ITO)-free planar perovskite solar cells (PSCs) were fabricated at a low temperature (150 °C) in this work based on the transparent electrode of photolithography processed nickel/gold (Ni/Au) mesh and the high conductivity polymer, PH1000. Ultrathin Au was introduced to increase the conductivity of metal mesh, and the optimal hexagonal Ni (30 nm)/Au (10 nm) mesh (line width of 5 μm) shows a transmittance close to 80% in the visible light region and a sheet resistance lower than 16.9 Ω/sq. The conductive polymer PH1000 not only smooths the raised surface of the metal mesh but also enhances the charge collection ability of metal mesh. The fabricated PSCs have the typical planar structure (glass/Ni-Au mesh/PH1000/PEDOT:PSS/MAyFA1-yPbIxCl3-x/PCBM/BCP/Ag) and the champion PSC (0.09 cm2) obtains a power conversion efficiency (PCE) of 13.88%, negligible current hysteresis, steady current density and PCE outputs, and good process repeatability. Its photovoltaic performance and stability are comparable to the reference PSC based on the ITO electrodes (PCE = 15.70%), which demonstrates that the Ni/Au mesh transparent electrodes are a promising ITO alternative to fabricate efficient PSCs. The relatively lower performance of Ni/Au based PSC results from the relatively slower charge extraction and stronger charge recombination than the ITO based PSC. Further, we tried to fabricate the large area (1 cm2) device and achieve a PCE over 6% with negligible hysteresis and steady current density and PCE outputs. The improvements of perovskite film quality and interface modification should be an effective approach to further enhance the device performance of Ni/Au based PSCs, and the Ni/Au mesh electrode may find wider applications in PSCs and flexible devices.
Project description:The most frequently used n-type electron transport layer (ETL) in high-efficiency perovskite solar cells (PSCs) is based on titanium oxide (TiO2) films, involving a high-temperature sintering (>450 °C) process. In this work, a dense, uniform, and pinhole-free compact titanium dioxide (TiOx) film was prepared via a facile chemical bath deposition process at a low temperature (80 °C), and was applied as a high-quality ETL for efficient planar PSCs. We tested and compared as-deposited substrates sintered at low temperatures (< 150 °C) and high temperatures (> 450 °C), as well as their corresponding photovoltaic properties. PSCs with a high-temperature treated TiO2 compact layer (CL) exhibited power conversion efficiencies (PCEs) as high as 15.50%, which was close to those of PSCs with low-temperature treated TiOx (14.51%). This indicates that low-temperature treated TiOx can be a potential ETL candidate for planar PSCs. In summary, this work reports on the fabrication of low-temperature processed PSCs, and can be of interest for the design and fabrication of future low-cost and flexible solar modules.
Project description:Organic-inorganic halide perovskites have been widely used in photovoltaic technologies. Despite tremendous progress in their efficiency and stability, perovskite solar cells (PSCs) are still facing the challenges of upscaling and stability for practical applications. As a mature film preparation technology, magnetron sputtering has been widely used to prepare metals, metallic oxides, and some semiconductor films, which has great application potential in the fabrication of PSCs. Here, a unique technology where high-quality perovskite films are prepared via magnetron sputtering for controllable composition, solvent-free, large-area, and massive production, is presented. This strategy transforms the perovskite materials from powder to thin films by magnetron sputtering and post-treatment (vapor-assisted treatment with methanaminium iodide gas and methylamine gas treatment), which is greatly favorable to manufacture tandem solar cells. The power conversion efficiency (PCE) of PSCs with perovskite films fabricated by magnetron sputtering is 6.14%. After optimization, high-performance perovskite films with excellent electronic properties are obtained and stable PSCs with excellent reproducibility are realized, showing a PCE of up to 15.22%. The entirely novel synthetic approach opens up a new and promising way to achieve high-throughput magnetron sputtering for large-area production in commercial applications of planar heterojunction and tandem PSCs.