Dataset Information

Effects of Foam Microbubbles on Electrical Resistivity and Capillary Pressure of Partially Saturated Porous Media.

ABSTRACT: Laboratory measurements of capillary pressure (Pc) and the electrical resistivity index (RI) of reservoir rocks are used to calibrate well logging tools and to determine reservoir fluid distribution. Significant studies on the methods and factors affecting these measurements in rocks containing oil, gas, and water are adequately reported in the literature. However, with the advent of chemical enhanced oil recovery (EOR) methods, surfactants are mixed with injection fluids to generate foam to enhance the gas injection process. Foam is a complex and non-Newtonian fluid whose behavior in porous media is different from conventional reservoir fluids. As a result, the effect of foam on Pc and the reliability of using known rock models such as the Archie equation to fit experimental resistivity data in rocks containing foam are yet to be ascertained. In this study, we investigated the effect of foam on the behavior of both Pc and RI curves in sandstone and carbonate rocks using both porous plate and two-pole resistivity methods at ambient temperature. Our results consistently showed that for a given water saturation (Sw), the RI of a rock increases in the presence of foam than without foam. We found that, below a critical Sw, the resistivity of a rock containing foam continues to rise rapidly. We argue, based on knowledge of foam behavior in porous media, that this critical Sw represents the regime where the foam texture begins to become finer, and it is dependent on the properties of the rock and the foam. Nonetheless, the Archie model fits the experimental data of the rocks but with resulting saturation exponents that are higher than conventional gas-water rock systems. The degree of variation in the saturation exponents between the two fluid systems also depends on the rock and fluid properties. A theory is presented to explain this phenomenon. We also found that foam affects the saturation exponent in a similar way as oil-wet rocks in the sense that they decrease the cross-sectional area of water available in the pores for current flow. Foam appears to have competing and opposite effects caused by the presence of clay, micropores, and conducting minerals, which tend to lower the saturation exponent at low Sw. Finally, the Pc curve is consistently lower in foam than without foam for the same Sw.

SUBMITTER: R Adebayo A

PROVIDER: S-EPMC7436130 | biostudies-literature | 2020 Jul

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Effects of Foam Microbubbles on Electrical Resistivity and Capillary Pressure of Partially Saturated Porous Media.

R Adebayo Abdulrauf A Isah Abubakar A Mahmoud Mohamed M Al-Shehri Dhafer D

Molecules (Basel, Switzerland) 20200726 15

Laboratory measurements of capillary pressure (Pc) and the electrical resistivity index (RI) of reservoir rocks are used to calibrate well logging tools and to determine reservoir fluid distribution. Significant studies on the methods and factors affecting these measurements in rocks containing oil, gas, and water are adequately reported in the literature. However, with the advent of chemical enhanced oil recovery (EOR) methods, surfactants are mixed with injection fluid ...[more]

PMID: 32722602

Similar Datasets

Project description:The propagation of foam in an oil reservoir depends on the creation and stability of the foam in the reservoir, specifically the creation and stability of foam films, or lamellae. As the foam propagates far from the injection well, superficial velocity and pressure gradient decrease with distance from the well. Experimental (Friedmann et al. Steam-foam mechanistic field trial in the midway-sunset field. SPERE. 1994, 9 (4), 297-304) and theoretical (Ashoori, et al. Roles of Transient and Local Equilibrium Foam Behaviour in Porous Media: Traveling Wave. Colloids Surf. A 2011, 337 (1-3), 228-242). studies relate concerns about foam propagation at low superficial velocity to the minimum velocity or pressure gradient for foam generation near the well (Gauglitz et al. Foam Generation in Homogeneous Porous Media. Chem. Eng. Sci. 2002, 57, 4037-4052; Rossen et al. Percolation Theory of Creation and Mobilization of Foams in Porous Media. AI Chem Eng. J. 1990, 36, (8)). The objective of this work is to measure the impact of surfactant concentration and gas fractional flow on foam generation. Theory (Kam et al. Model for Foam Generation in Homogeneous Media. SPE J. 2003, 8 (4): 417-42, SPE-87334-PA; Rossen 1990) relates foam generation to gas fractional flow and, indirectly, to the stability of foam films, or lamellae, which in turn depends on surfactant concentration (Apaydin et al. Surfactant Concentration and End Effects on Foam Flow in Porous Media. (Apaydin et al.Transp Porous Media. 2001, 43, 511-536). However, the link between foam generation and surfactant concentration has not been established experimentally. In our experiments, nitrogen foam is generated in a core of Bentheimer sandstone. The foam-generation experiments consist of measuring the minimum velocity for foam generation as a function of gas fractional flow at three surfactant concentrations well above the critical micelle concentration. Experimental results show that the minimum velocity for foam generation decreases with increasing liquid fraction, as shown by previous foam generation studies (Friedmann et al., 1994; Rossen and Gauglitz, 1990). Additionally, our results show that this velocity decreases with increasing surfactant concentration, far above the CMC. We also propose a workflow for screening out the experimental artifacts that can distort the trigger velocity.

Dataset Information

Effects of Foam Microbubbles on Electrical Resistivity and Capillary Pressure of Partially Saturated Porous Media.

Publications

Effects of Foam Microbubbles on Electrical Resistivity and Capillary Pressure of Partially Saturated Porous Media.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets