Data on the estimation of thermomechanical damage for fired clay bricks.
Ontology highlight
ABSTRACT:
SUBMITTER: Mpoung LA
PROVIDER: S-EPMC8063730 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:In the current study, waste marble powder was utilized to produce lightweight fired clay bricks and in the treatment of flue gases. Marble waste powder used in clay bricks and flue gas treatment was collected from local marble processing plants, and its chemical composition was analyzed using energy-dispersive X-ray analysis and X-ray fluorescence. Clay bricks were produced in local fired clay brick kiln by partial replacement (10-40%) of clay with calcined and uncalcined waste marble powder. The temperature in the firing zone of the kiln was 1000-1100 °C. Clay brick properties such as compressive strength, bulk density, porosity, and water absorption were analyzed. Results show that the porosity of clay bricks increases with an increase in marble waste percentage, and due to an increase in porosity, water absorption of clay bricks also increases, while compressive strength and bulk density decrease. Clay bricks with 10% uncalcined marble waste and 20% calcined marble waste satisfy the required Turkish and European compressive strength standard. Marble waste decreases the concentration of sulfur dioxide and particulate matter in flue gases. There is up to 43 and 65% reduction in the concentration of sulfur dioxide and particulate matters, respectively, in flue gases, after treatment with marble waste. The addition of marble waste to clay bricks is an effective and economical solution for waste marble powder management. Furthermore, it can be used for the treatment of flue gases from brick kilns before its addition to clay bricks.
| S-EPMC8427632 | biostudies-literature
Project description:Dating of clay bricks (adobe) and plasters is a relevant topic not only for building historians in the Pannonian region. Especially in vernacular architecture in this region, clay with straw amendments is a dominant construction material. The paper presents the potential of the molecular decay of these amendments to establish prediction tools for age based on infrared spectroscopic measurements. Preliminary results revealed spectral differences between the different plant parts, especially culms, nodes, and ear spindles. Based on these results, a first prediction model is presented including 14 historic samples. The coefficient of determination for the validation reached 62.2%, the (RMSE) root mean squared error amounted to 93 years. Taking the limited sample amount and the high material heterogeneity into account, this result can be seen as a promising output. Accordingly, sample size should be increased to a minimum of 100 objects and separate models for the different plant parts should be established.
| S-EPMC7144354 | biostudies-literature
Project description:This article presents data from the investigation of the thermal characteristics and mechanical behaviors of twelve different compositions of a polyurethane shape memory polymer (SMP). Each of the SMP compositions has a unique molar ratio of three monomers: (i) hexamethylene diisocyanate (HDI), (ii) N,N,N',N'-Tetrakis(2-Hydroxypropyl)ethylenediamine (HPED), and (iii) Triethanolamine (TEA). The thermal characteristic datasets for each composition include the glass transition temperatures, as obtained from differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA), and the thermal degradation thresholds, as found from thermogravimetric analysis (TGA). The mechanical behaviors of the SMPs are represented by the failure stresses and strains, as obtained by cyclic tensile testing and failure testing, respectively. The interpretation of these measurements as well as a discussion of the potential usage of candidate SMP compositions for medical devices can be found in the companion article by Kunkel et al. (2018) [1], "Synthesis and characterization of bio-compatible shape memory polymers with potential applications to endovascular embolization of intracranial aneurysms."
| S-EPMC7495509 | biostudies-literature
Project description:This paper presents the residual mechanical properties of concrete made with crushed bricks and clay roof tile aggregates after exposure to high temperatures. One referent mixture and eight mixtures with different percentages of replacement of natural aggregate by crushed bricks and roof tiles are experimentally tested. The properties of the concrete were measured before and after exposure to 200, 400, 600 and 800 °C. In order to evaluate the basic residual mechanical properties of concrete with crushed bricks and roof tiles after exposure to high temperatures, ultrasonic pulse velocity is used as a non-destructive test method and the results are compared with those of a destructive method for validation. The mixture with the highest percentage of replacement of natural aggregate by crushed brick and roof tile aggregate has the best physical, mechanical, and thermal properties for application of such concrete in precast concrete elements exposed to high temperatures.
| S-EPMC5502988 | biostudies-other
Project description:Effective pretreatment of spectral reflectance is vital to model accuracy in soil parameter estimation. However, the classic integer derivative has some disadvantages, including spectral information loss and the introduction of high-frequency noise. In this paper, the fractional order derivative algorithm was applied to the pretreatment and partial least squares regression (PLSR) was used to assess the clay content of desert soils. Overall, 103 soil samples were collected from the Ebinur Lake basin in the Xinjiang Uighur Autonomous Region of China, and used as data sets for calibration and validation. Following laboratory measurements of spectral reflectance and clay content, the raw spectral reflectance and absorbance data were treated using the fractional derivative order from the 0.0 to the 2.0 order (order interval: 0.2). The ratio of performance to deviation (RPD), determinant coefficients of calibration ([Formula: see text]), root mean square errors of calibration (RMSEC), determinant coefficients of prediction ([Formula: see text]), and root mean square errors of prediction (RMSEP) were applied to assess the performance of predicting models. The results showed that models built on the fractional derivative order performed better than when using the classic integer derivative. Comparison of the predictive effects of 22 models for estimating clay content, calibrated by PLSR, showed that those models based on the fractional derivative 1.8 order of spectral reflectance ([Formula: see text] = 0.907, RMSEC = 0.425%, [Formula: see text] = 0.916, RMSEP = 0.364%, and RPD = 2.484 ≥ 2.000) and absorbance ([Formula: see text] = 0.888, RMSEC = 0.446%, [Formula: see text] = 0.918, RMSEP = 0.383% and RPD = 2.511 ≥ 2.000) were most effective. Furthermore, they performed well in quantitative estimations of the clay content of soils in the study area.
| S-EPMC5608292 | biostudies-literature
Project description:The dataset presented in this article represent the drying characteristics of a semi-automated gas-fired fish dryer. A cabinet dryer was constructed mainly from mild steel sheet metal and stainless steel, and was used for drying prepared fish samples of Clarias gariepinus species. Major operating parameters which included mass of fish, mass of Liquefied Petroleum Gas used, inside temperature of the dryer, and drying time were monitored. Also, output parameters such as the moisture content and energy utilization amongst others were observed and recorded at varying time intervals and specified drying temperatures. The drying temperature was sustained via an incorporated PID temperature controller that allowed drying to proceed until a relatively constant mass of the dried fish samples was attained. The information contained in this data article include a schematic drawing of drying kinetics analysis of the semi-automated gas-fired fish dryer and a pictorial view of the gas-fired cabinet dryer. Also included are pictorial representations of the washed and neatly folded degutted fish samples and dried fish samples. Data provided in this article are those relating to process parameters of the semi-automated fish dryer, data of output parameters of the fish dryer and comparisons of moisture content and energy utilization at different drying temperatures with time.
| S-EPMC5996308 | biostudies-literature
Project description:In order to identify potential zones for clay mineral (kaolinite) in Ranong province, Thailand, ten 2D ERT survey lines were deployed across potential site. The data were collected using the IRIS Syscal Pro Plus multi-electrode imaging system with internal switchbox and an array of 48 steel electrodes. The Dipole-Dipole configuration was utilized with electrode separations of 10 m. The Res2DInv software was used to process the data. Images for the resistivity survey are presented as 2D cross section of resistivity profile. The data were interpreted by comparing with geology of the area and based on the available lithological borehole information.
| S-EPMC7163305 | biostudies-literature
Project description:Natural materials can provide cost-effective way in the development of various products for specific applications. On the hand, physicochemical properties of composite materials can be enhanced to perform a specific process of interest such as wastewater treatment. Clay materials have been used for many applications including brick making and wastewater treatment. To enhance the properties of natural materials such as clay, multiwalled carbon nanotubes (MWCNTs) were used to enhance the properties of natural clays. Natural clays and MWCNTs composites were characterized to provide insights as a starting point for various applications. There are two sets of data presented in this study: i) raw material, unheated and heated (at 900 °C); ii) natural clay, MWCNTs and natural clay/MWCNTs composites. The chemical composition and phase identification analyzes were carried out using X-ray Fluorescence (XRF) and X-Ray Diffraction (XRD), respectively. A Fourier-transform infrared (FTIR) spectrometer was used to determine the functional groups of the samples. The UV-vis analyzes were carried out to investigate the reflectance percentage of the natural clays and the composites samples. The Thermogravimetric analysis (TGA) analyzes were performed to investigate the weight loss and dehydration process of the samples. The presented data showed that natural clays and natural clays/MWCNTs composites can be used for various applications such as construction industry, for cosmetic usages and for the removal of pollutants in aqueous solutions.
| S-EPMC8661467 | biostudies-literature
Project description:In this paper, operational data of a natural gas-fired generation engine at 2 MW of power is presented. This engine is used as part of the power supply system of a flexible packaging transformation and conversion plant. This plant, besides having the power supply generated by the engine, receives electrical energy from the network. The data collected from this engine corresponds to measurements taken before, during and after engine stops, whether due to engine maintenance stops, engine failures or external power grid failures. The measurement was made every 10 seconds, and for the storage of these data a data acquisition software was used, which, besides allowing to take these data, shows in real time the electrical behavior of the electrical supply system, as well as the mechanical behavior of the engine.
| S-EPMC7096767 | biostudies-literature
Project description:The selective catalytic reduction (SCR) decomposition of nitrogen oxide (de-NO x ) process in coal-fired power plants not only displays nonlinearity, large inertia and time variation but also a lag in NO x analysis; hence, it is difficult to obtain an accurate model that can be used to control NH3 injection during changes in the operating state. In this work, a novel dynamic inferential model with delay estimation was proposed for NO x emission prediction. First, k-nearest neighbour mutual information was used to estimate the time delay of the descriptor variables, followed by reconstruction of the phase space of the model data. Second, multi-scale wavelet kernel partial least square was used to improve the prediction ability, and this was followed by verification using benchmark dataset experiments. Finally, the delay time difference method and feedback correction strategy were proposed to deal with the time variation of the SCR de-NO x process. Through the analysis of the experimental field data in the steady state, the variable state and the NO x analyser blowback process, the results proved that this dynamic model has high prediction accuracy during state changes and can realize advance prediction of the NO x emission.
| S-EPMC7062099 | biostudies-literature