Metal Oxide Quantum Dots Embedded in Silica Matrices Made by Flame Spray Pyrolysis.
Ontology highlight
ABSTRACT:
SUBMITTER: Riad KB
PROVIDER: S-EPMC8153950 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:The most critical part of the flame spray pyrolysis (FSP) process is the nozzle, since it plays a key role in setting the spray properties. In this study, we developed an approach to adjust the nozzle throat gap size for a desired dispersion gas flow rate and upstream pressure, based on the external size and shape of a two phase external mixing nozzle. An equation was derived and validated by comparing the predicted gas flow rates with the data provided in a commercial nozzle supplier chart. Experiments were also conducted in our lab-scale FSP reactor to test the validity of the predictions. The approach developed here was found to closely predict the gap size necessary to pass the required dispersion gas flow at a desired pressure drop. Error in predictions was found to be less than 3% at an upstream pressure range of 3-10 bars. The isentropic flow assumption for perfect gases across the convergent-divergent nozzle was found to fail below 2 bars, consistent with the theory applied. By using the method here, the nozzle setting for a desired operation in an FSP process can be easily done, minimizing the time-consuming trial and error steps needed otherwise.
| S-EPMC7509832 | biostudies-literature
Project description:The synthesis routes are presented for the preparation of nanocomposites composed of nanocrystals placed inside SBA-15 silica pores. The procedures assume treating the silica channels as nanoreactors, where nanocrystals are created as a result of thermal decomposition of internal functional units. Its sizes and chemical composition can be modified by the change of functional group types and density inside silica channels. The procedure is demonstrated by the example of copper pyrophosphate quantum dots and silver oxide nanoparticles inside silica mezochannels. The method can be easily adopted to other types of nanocrystals that can be synthesized inside silica nanoreactors.
| S-EPMC7254358 | biostudies-literature
Project description:The oxygen reduction reaction (ORR) is the rate-limiting reaction in the cathode side of fuel cells. In the quest for alternatives to Pt-electrodes as cathodes in ORR, appropriate transition metal oxide-based electrocatalysts are needed. In the present work, we have synthesized Co3O4 and CoO/Co3O4 nanostructures using flame spray pyrolysis (FSP), as electrocatalysts for ORR in acidic and alkaline media. A detailed study of the effect of (Co-oxide)/Pt ratio on ORR efficiency shows that the present FSP-made Co-oxides are able to perform ORR at very low-Pt loading, 0.4% of total metal content. In acid medium, an electrode with (5.2% Pt + 4.8% Co3O4), achieved the highest ORR performance (Jmax = 8.31 mA/cm2, E1/2 = 0.66 V). In alkaline medium, superior performance and stability have been achieved by an electrode with (0.4%Pt + 9.6% (CoO/Co3O4)) with ORR activity (Jmax = 3.5 mA/cm2, E1/2 = 0.08 V). Using XRD, XPS, Raman and TEM data, we discuss the structural and electronic aspects of the FSP-made Co-oxide catalysts in relation to the ORR performance. Cyclic voltammetry data indicate that the ORR process involves active sites associated with Co3+ cations at the cobalt oxide surface. Technology-wise, the present work demonstrates that the developed FSP-protocols, constitutes a novel scalable process for production of co-oxides appropriate for oxygen reduction reaction electrodes.
| S-EPMC8066371 | biostudies-literature
Project description:Engineering of oxygen vacancies (Vo) in nanomaterials allows diligent control of their physicochemical properties. SrTiO3 possesses the typical ABO3 structure and has attracted considerable attention among the titanates due to its chemical stability and its high conduction band energy. This has resulted in its extensive use in photocatalytic energy-related processes, among others. Herein, we introduce the use of Flame Spray Pyrolysis (FSP); an industrial and scalable process to produce Vo-rich SrTiO3 perovskites. We present two types of Anoxic Flame Spray Pyrolysis (A-FSP) technologies using CH4 gas as a reducing source: Radial A-FSP (RA-FSP); and Axial A-FSP (AA-FSP). These are used for the control engineering of oxygen vacancies in the SrTiO3-x nanolattice. Based on X-ray photoelectron spectroscopy, Raman and thermogravimetry-differential thermal analysis, we discuss the role and the amount of the Vos in the so-produced nano-SrTiO3-x, correlating the properties of the nanolattice and energy-band structure of the SrTiO3-x. The present work further corroborates the versatility of FSP as a synthetic process and the potential future application of this process to engineer photocatalysts with oxygen vacancies in quantities that can be measured in kilograms.
| S-EPMC10891825 | biostudies-literature
Project description:Exosomes are attracting attention as new biomarkers for monitoring the diagnosis and prognosis of certain diseases. Colorimetric-based lateral-flow assays have been previously used to detect exosomes, but these have the disadvantage of a high limit of detection. Here, we introduce a new technique to improve exosome detection. In our approach, highly bright multi-quantum dots embedded in silica-encapsulated nanoparticles (M-QD-SNs), which have uniform size and are brighter than single quantum dots, were applied to the lateral flow immunoassay method to sensitively detect exosomes. Anti-CD63 antibodies were introduced on the surface of the M-QD-SNs, and a lateral flow immunoassay with the M-QD-SNs was conducted to detect human foreskin fibroblast (HFF) exosomes. Exosome samples included a wide range of concentrations from 100 to 1000 exosomes/µL, and the detection limit of our newly designed system was 117.94 exosome/μL, which was 11 times lower than the previously reported limits. Additionally, exosomes were selectively detected relative to the negative controls, liposomes, and newborn calf serum, confirming that this method prevented non-specific binding. Thus, our study demonstrates that highly sensitive and quantitative exosome detection can be conducted quickly and accurately by using lateral immunochromatographic analysis with M-QD-SNs.
| S-EPMC8002883 | biostudies-literature
Project description:In this study, we present the preparation of graphene quantum dots (GQDs) and graphene oxide quantum dots (GOQDs). GQDs/GOQDs are prepared by an easy electrochemical exfoliation method, in which two graphite rods are used as electrodes. The electrolyte used is a combination of citric acid and alkali hydroxide in water. Four types of quantum dots, GQD1-GQD4, are prepared by varying alkali hydroxide concentration in the electrolyte, while keeping the citric acid concentration fixed. Variation of alkali hydroxide concentration in the electrolyte results in the production of GOQDs. Balanced reaction of citric acid and alkali hydroxide results in the production of GQDs (GQD3). However, three variations in alkali hydroxide concentration result in GOQDs (GQD1, GQD2, and GQD4). GOQDs show tunable oxygen functional groups, which are confirmed by X-ray photoelectron spectroscopy. GQDs/GOQDs show absorption in the UV region and show excitation-dependent photoluminescence behavior. The obtained average size is 2-3 nm, as revealed by transmission electron microscopy. X-ray diffraction peak at around 10° and broad D band peak at 1350 cm-1 in Raman spectra confirm the presence of oxygen-rich functional groups on the surface of GOQDs. These GQDs and GOQDs show blue to green luminescence under 365 nm UV irradiation.
| S-EPMC6645081 | biostudies-literature
Project description:By doping a dielectric layer material and improving the device's structure, the electrical characteristics of a memristor can be effectively adjusted, and its application field can be expanded. In this study, graphene quantum dots are embedded in the dielectric layer to improve the performance of a starch-based memristor, and the PMMA layer is introduced into the upper and lower interfaces of the dielectric layer. The experimental results show that the switching current ratio of the Al/starch: GQDs/ITO device was 102 times higher than that of the Al/starch/ITO device. However, the switching current ratio of the Al/starch: GQDs/ITO device was further increased, and the set voltage was reduced (-0.75 V) after the introduction of the PMMA layer. The introduction of GQDs and PMMA layers can regulate the formation process of conductive filaments in the device and significantly improve the electrical performance of the memristor.
| S-EPMC10708532 | biostudies-literature
Project description:Tin dioxide (SnO2) nanoparticles synthesized via flame spray pyrolysis (FSP) have promising applications for gas sensors. The formation of SnO2 nanoparticles in the gas-phase has been investigated using single droplet combustion and FSP. Precursor solutions of Tin (II) 2-ethylhexanoate dissolved in Xylene with varying Sn concentrations were selected as the precursor-solvent system. The selected precursor-solvent system has its stability and ability to synthesize homogeneous nanoparticles, compared to metal nitrate based precursor solutions. The precursor-solvent system was studied using attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy and thermogravimetric analysis (TGA). The SnO2 nanoparticles were characterized using X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), and transmission electron microscopy (TEM). Droplet surface micro-explosions were observed during the single droplet combustion of the precursor solutions. It is because of the heterogeneous vapor-phase nucleation, which is beneath the liquid droplet surface and caused by precursor thermal decomposition. The results show that the size of nanoparticles obtained both from FSP and single droplet combustion increases with increasing metal-precursor concentration. The TEM images of the particles from such droplet combustion reveal two types of nanoparticles with different sizes and morphologies. The current work provides fundamental understanding of precursor decomposition and particle formation during single droplet combustion, which help in-depth understanding of the flame spray pyrolysis.
| S-EPMC7116032 | biostudies-literature
Project description:A flame spray pyrolysis (FSP) method has been developed, for controlled doping of BiVO4 nanoparticles with W and Zr in tandem with the oxygen vacancies (Vo) of the BiVO4 lattice. Based on XPS and Raman data, we show that the nanolattice of W-BiVO4 and Zr-BiO4 can be controlled to achieve optimal O2 evolution from H2O photocatalysis. A synergistic effect is found between the W- and Zr-doping level in correlation with the Vo-concentration. FSP- made W-BiVO4 show optimal photocatalytic O2-production from H2O, up to 1020 μmol/(g × h) for 5%W-BiVO4, while the best performing Zr-doped achieved 970 μmol/(g × h) for 5%Zr-BiVO4. Higher W-or Zr-doping resulted in deterioration in photocatalytic O2-production from H2O. Thus, engineering of FSP-made BiVO4 nanoparticles by precise control of the lattice and doping-level, allows significant enhancement of the photocatalytic O2-evolution efficiency. Technology-wise, the present work demonstrates that flame spray pyrolysis as an inherently scalable technology, allows precise control of the BiVO4 nanolattice, to achieve significant improvement of its photocatalytic efficiency.
| S-EPMC7920441 | biostudies-literature
Project description:In this work, green-emitting InP/ZnS quantum dots (QDs) modified with 1-dodecanethiol were embedded into silica by two methods to improve their photostability while maintaining a high photoluminescence quantum yield (PLQY) and a color coordinate. A monolithic QD-silica composite prepared by a non-aqueous route with tetraethyl orthosilicate and lactic acid featured low transparency, a loss of the color purity of green, and a PLQY of 1.6%, which was considerably lower than that of the original QDs (67%). The decrease of the PLQY was attributed to QD aggregation in the sol-gel process and degradation of the QDs by the acid. The alternative method involved stirring a toluene dispersion of the QDs with tetramethyl orthosilicate (TMOS) for 20 h or 7 days. The PLQY of the TMOS-modified InP/ZnS QDs (20 h) was 62%, which was only slightly lower than that of the original QDs. The PLQY decreased to 52% when the duration of aging was prolonged to 7 days. This decrease was attributed to desorption of surface modifiers from the QD surface and oxidative degradation by oxygen dissolved in toluene. Herein, the color coordinate was maintained stably. Photostability was evaluated by continuous irradiation of the samples by a blue light emitting diode. The decrease of photoluminescence (PL) intensity was suppressed by the silica encapsulation. In particular, the PL intensity of the TMOS-modified InP/ZnS QD sample (7 d) maintained 99% of its initial intensity. Silica encapsulation of InP/ZnS QDs prevented contact of the QDs with oxygen in the air, resulting in improved photostability.
| S-EPMC9082771 | biostudies-literature