Dataset Information

Experimental Demonstration of Light Focusing Enabled by Monolithic High-Contrast Grating Mirrors.

ABSTRACT: We present the first experimental demonstration of a planar focusing monolithic subwavelength grating mirror. The grating is formed on the surface of GaAs and focuses 980 nm light in one dimension on the high-refractive-index side of the mirror. According to our measurements, the focal length is 475 μm (300 μm of which is GaAs) and the numerical aperture is 0.52. The intensity of the light at the focal point is 23 times larger than that of the incident light. To the best of our knowledge, this is the highest value reported for a grating mirror. Moreover, the full width at half-maximum (FWHM) at the focal point is only 3.9 μm, which is the smallest reported value for a grating mirror. All of the measured parameters are close to or very close to the theoretically predicted values. Our realization of a sophisticated design of a focusing monolithic subwavelength grating opens a new avenue to technologically simple fabrication of the gratings for use in diverse optoelectronic materials and applications.

SUBMITTER: Komar P

PROVIDER: S-EPMC8289169 | biostudies-literature | 2021 Jun

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Experimental Demonstration of Light Focusing Enabled by Monolithic High-Contrast Grating Mirrors.

Komar Paulina P Gȩbski Marcin M Lott James A JA Czyszanowski Tomasz T Wasiak Michał M

ACS applied materials & interfaces 20210519 21

We present the first experimental demonstration of a planar focusing monolithic subwavelength grating mirror. The grating is formed on the surface of GaAs and focuses 980 nm light in one dimension on the high-refractive-index side of the mirror. According to our measurements, the focal length is 475 μm (300 μm of which is GaAs) and the numerical aperture is 0.52. The intensity of the light at the focal point is 23 times larger than that of the incident light. To the best of our knowledge, this i ...[more]

PMID: 34008943

Similar Datasets

Project description:This paper concerns the feasibility of x-ray differential phase contrast (DPC) tomosynthesis imaging using a grating-based DPC benchtop experimental system, which is equipped with a commercial digital flat-panel detector and a medical-grade rotating-anode x-ray tube. An extensive system characterization was performed to quantify its imaging performance.The major components of the benchtop system include a diagnostic x-ray tube with a 1.0 mm nominal focal spot size, a flat-panel detector with 96 μm pixel pitch, a sample stage that rotates within a limited angular span of ± 30°, and a Talbot-Lau interferometer with three x-ray gratings. A total of 21 projection views acquired with 3° increments were used to reconstruct three sets of tomosynthetic image volumes, including the conventional absorption contrast tomosynthesis image volume (AC-tomo) reconstructed using the filtered-backprojection (FBP) algorithm with the ramp kernel, the phase contrast tomosynthesis image volume (PC-tomo) reconstructed using FBP with a Hilbert kernel, and the differential phase contrast tomosynthesis image volume (DPC-tomo) reconstructed using the shift-and-add algorithm. Three inhouse physical phantoms containing tissue-surrogate materials were used to characterize the signal linearity, the signal difference-to-noise ratio (SDNR), the three-dimensional noise power spectrum (3D NPS), and the through-plane artifact spread function (ASF).While DPC-tomo highlights edges and interfaces in the image object, PC-tomo removes the differential nature of the DPC projection data and its pixel values are linearly related to the decrement of the real part of the x-ray refractive index. The SDNR values of polyoxymethylene in water and polystyrene in oil are 1.5 and 1.0, respectively, in AC-tomo, and the values were improved to 3.0 and 2.0, respectively, in PC-tomo. PC-tomo and AC-tomo demonstrate equivalent ASF, but their noise characteristics quantified by the 3D NPS were found to be different due to the difference in the tomosynthesis image reconstruction algorithms.It is feasible to simultaneously generate x-ray differential phase contrast, phase contrast, and absorption contrast tomosynthesis images using a grating-based data acquisition setup. The method shows promise in improving the visibility of several low-density materials and therefore merits further investigation.

Project description:The authors present initial progress toward a clinically compatible x-ray phase contrast CT system, using glancing-angle x-ray grating interferometry to provide high contrast soft tissue images at estimated by computer simulation dose levels comparable to conventional absorption based CT.DPC-CT scans of a joint phantom and of soft tissues were performed in order to answer several important questions from a clinical setup point of view. A comparison between high and low fringe visibility systems is presented. The standard phase stepping method was compared with sliding window interlaced scanning. Using estimated dose values obtained with a Monte-Carlo code the authors studied the dependence of the phase image contrast on exposure time and dose.Using a glancing angle interferometer at high x-ray energy (∼ 45 keV mean value) in combination with a conventional x-ray tube the authors achieved fringe visibility values of nearly 50%, never reported before. High fringe visibility is shown to be an indispensable parameter for a potential clinical scanner. Sliding window interlaced scanning proved to have higher SNRs and CNRs in a region of interest and to also be a crucial part of a low dose CT system. DPC-CT images of a soft tissue phantom at exposures in the range typical for absorption based CT of musculoskeletal extremities were obtained. Assuming a human knee as the CT target, good soft tissue phase contrast could be obtained at an estimated absorbed dose level around 8 mGy, similar to conventional CT.DPC-CT with glancing-angle interferometers provides improved soft tissue contrast over absorption CT even at clinically compatible dose levels (estimated by a Monte-Carlo computer simulation). Further steps in image processing, data reconstruction, and spectral matching could make the technique fully clinically compatible. Nevertheless, due to its increased scan time and complexity the technique should be thought of not as replacing, but as complimentary to conventional CT, to be used in specific applications.

Dataset Information

Experimental Demonstration of Light Focusing Enabled by Monolithic High-Contrast Grating Mirrors.

Publications

Experimental Demonstration of Light Focusing Enabled by Monolithic High-Contrast Grating Mirrors.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets