Characterization of a PCB Based Pressure Sensor and Its Joining Methods for the Metal Membrane.
Ontology highlight
ABSTRACT:
SUBMITTER: Schwenck A
PROVIDER: S-EPMC8402279 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Tunneling conductance among nanoparticle arrays is extremely sensitive to the spacing of nanoparticles and might be applied to fabricate ultra-sensitive sensors. Such sensors are of paramount significance for various application, such as automotive systems and consumer electronics. Here, we represent a sensitive pressure sensor which is composed of a piezoresistive strain transducer fabricated from closely spaced nanoparticle films deposited on a flexible membrane. Benefited from this unique quantum transport mechanism, the thermal noise of the sensor decreases significantly, providing the opportunity for our devices to serve as high-performance pressure sensors with an ultrahigh resolution as fine as about 0.5 Pa and a high sensitivity of 0.13 kPa-1. Moreover, our sensor with such an unprecedented response capability can be operated as a barometric altimeter with an altitude resolution of about 1 m. The outstanding behaviors of our devices make nanoparticle arrays for use as actuation materials for pressure measurement.
| S-EPMC6731318 | biostudies-literature
Project description:Capacitively coupled contactless conductivity detection (C?D) is an improved approach to avoid the problems of labor-intensive, time-consuming and insufficient accuracy of plate count as well as the high-cost apparatus of flow cytometry (FCM) in bacterial counting. This article describes a novel electrode-integrated printed-circuit-board (PCB)-based C?D device, which supports the simple and safe exchange of capillaries and improves the sensitivity and repeatability of the contactless detection. Furthermore, no syringe pump is needed in the detection, it reduces the system size, and, more importantly, avoids the effect on the bacteria due to high pressure. The recovered bacteria after C?D detection at excitation of 25 Vpp and 60?120 kHz were analyzed by flow cytometry, and a survival rate higher than 96% was given. It was verified that C?D detection did not influence the bacterial viability. Moreover, bacteria concentrations from 10? cells/mL to 10? cells/mL were measured in a linear range, and relative standard deviation (RSD) is below 0.2%. In addition, the effects on bacteria and C?D from background solutions were discussed. In contrast to common methods used in most laboratories, this method may provide a simple solution to in situ detection of bacterial cultures.
| S-EPMC6356519 | biostudies-literature
Project description:Cellular membranes are densely covered by proteins. Steric pressure generated by protein collisions plays a significant role in shaping and curving biological membranes. However, no method currently exists for measuring steric pressure at membrane surfaces. Here, we developed a sensor based on Förster resonance energy transfer (FRET), which uses the principles of polymer physics to precisely detect changes in steric pressure. The sensor consists of a polyethylene glycol chain tethered to the membrane surface. The polymer has a donor fluorophore at its free end, such that FRET with acceptor fluorophores in the membrane provides a real-time readout of polymer extension. As a demonstration of the sensor, we measured the steric pressure generated by a model protein involved in membrane bending, the N-terminal homology domain (ENTH) of Epsin1. As the membrane becomes crowded by ENTH proteins, the polymer chain extends, increasing the fluorescence lifetime of the donor. Drawing on polymer theory, we use this change in lifetime to calculate steric pressure as a function of membrane coverage by ENTH, validating theoretical equations of state. Further, we find that ENTH's ability to break up larger vesicles into smaller ones correlates with steric pressure rather than the chemistry used to attach ENTH to the membrane surface. This result addresses a long-standing question about the molecular mechanisms of membrane remodeling. More broadly, this sensor makes it possible to measure steric pressure in situ during diverse biochemical events that occur on membrane surfaces, such as membrane remodeling, ligand-receptor binding, assembly of protein complexes, and changes in membrane organization.
| S-EPMC8274331 | biostudies-literature
Project description:The foot arch index is an important index to evaluate the health of human feet and the biomechanics line, aiming at addressing the shortcomings of the low efficiency and slow speed of manual foot arch index measurement; in this work, an automatic foot arch index measurement method based on a flexible membrane pressure sensor was proposed. The distribution of plantar pressure data was obtained from the flexible membrane pressure sensor and converted into a digital image. The 8-neighborhood correlation pixel method was proposed to remove the interference of isolated noise points. In order to remove the toes' data without affecting the foot sole data, the row element association algorithm was proposed. The front and back endpoints of the foot were automatically located to obtain the foot length, and the foot arch index was also automatically obtained based on the foot arch pressure area. Whether it was a high arch foot, flat foot or normal foot, the method proposed in this paper could accurately and quickly distinguish them. The prototype was developed, and its feasibility and validity were verified by a series of tests.
| S-EPMC7285023 | biostudies-literature
Project description:Surface Acoustic Wave (SAW) sensors are small, passive and wireless devices. We present here the latest results obtained in a project aimed at developing a SAW-based implantable pressure sensor, equipped with a well-defined, 30 μm-thick, 4.7 mm-in-diameter, Lithium Niobate (LN) membrane. A novel fabrication process was used to solve the issue of accurate membrane etching in LN. LN/Si wafers were fabricated first, using wafer-bonding techniques. Grinding/polishing operations followed, to reduce the LN thickness to 30 μm. 2.45 GHz SAW Reflective Delay-Lines (R-DL) were then deposited on LN, using a combination of e-beam and optical lithography. The R-DL was designed in such a way as to allow for easy temperature compensation. Eventually, the membranes were etched in Si. A dedicated set-up was implemented, to characterize the sensors versus pressure and temperature. The achieved pressure accuracy is satisfactory (±0.56 mbar). However, discontinuities in the response curve and residual temperature sensitivity were observed. Further experiments, modeling and simulations were used to analyze the observed phenomena. They were shown to arise essentially from the presence of growing thermo-mechanical strain and stress fields, generated in the bimorph-like LN/Si structure, when the temperature changes. In particular, buckling effects explain the discontinuities, observed around 43 °C, in the response curves. Possible solutions are suggested and discussed.
| S-EPMC6211043 | biostudies-other
Project description:This article describes the effects of changing monomer and cross-linker concentrations on the mass gain, water permeability, Pd-Fe nanoparticle (NP) loading, and the rate of degradation of 3,3',4,4',5-pentachlorobiphenyl (PCB 126) of pore functionalized polyvinylidene fluoride (PVDF) membranes. In this study, monomer (acrylic acid (AA)) and cross-linker (N, N'- methylene-bis (acrylamide)) concentrations were varied from 10 to 20 wt% of polymer solution and 0.5-2 mol% of monomer concentration, respectively. Results showed that responsive behavior of membrane could be tuned in terms of water permeability over a range of 270-1 L m-2 h-1 bar-1, which is a function of water pH. The NP size on the membrane surface was found in the range of 16-23 nm. With increasing cross-linker density the percentage of smaller NPs (< 10 nm) increases due to smaller mesh size formation during in-situ polymerization of membrane. NP loading was found to vary from 0.21 to 0.94 mg per cm2 of membrane area depending on the variation of available carboxyl groups in membrane pore domain. The NPs functionalized membranes were then tested for use as a platform for the degradation of PCB 126. The observed batch reaction rate (Kobs) for PCB 126 degradation for per mg of catalyst loading was found 0.08-0.1 h-1. Degradation study in convective flow mode shows 98.6% PCB 126 is degraded at a residence time of 46.2 s. The corresponding surface area normalized reaction rate (K sa ) is found about two times higher than K sa of batch degradation; suggesting elimination of the effect of diffusion resistance for degradation of PCB 126 in convective flow mode operation. These Pd-Fe-PAA-PVDF membranes and nanoparticles are characterized by TGA, contact angle measurement, surface zeta potential, XRD, SEM, XPS, FIB, TEM and other techniques reveal the details about the membrane surface, pores and nanoparticles size, shape and size-distribution. Statistical analysis based on experimental results allows us to depict responsive behavior of functionalized membrane. In our best knowledge this paper first time reports detail study on responsive behavior of pore functionalized membrane in terms of permeability, NPs size, metal loading and its effect on PCB 126 degradation in a quantified approach.
| S-EPMC6358284 | biostudies-literature
Project description:Flexible and wearable pressure sensors have attracted extensive attention in domains, such as electronic skin, medical monitoring and human-machine interaction. However, developing a pressure sensor with high sensitivity, mechanical stability and a wide detection range remains a huge challenge. In this work, a flexible capacitive pressure sensor, based on a Ti3C2T x (MXene)/polyvinyl pyrrolidone (PVP) composite nanofiber membrane (CNM), prepared via an efficient electrospinning process, is presented. The experimental results show that even a small mass fraction of MXene can effectively decrease the compression modulus of the PVP nanofiber membrane, thus enhancing the sensing performance. Specifically, the sensor based on (0.1 wt% MXene)/PVP CNM has a high sensitivity (0.5 kPa-1 at 0-1.5 kPa), a fast response/recovery time (45/45 ms), a wide pressure detection range (0-200 kPa), a low detection limit (∼9 Pa) and an excellent mechanical stability (8000 cycles). Due to its superior performance, the sensor can monitor subtle changes in human physiology and other signals, such as pulse, respiration, human joint motions and airflow. In addition, a 4 × 4 sensor array is fabricated that can accurately map the shape and position of objects with good resolution. The high-performance flexible pressure sensor, as developed in this work, shows good application prospects in advanced human-computer interface systems.
| S-EPMC9470067 | biostudies-literature
Project description:In this study, a flexible pressure sensor with highly stable performance is presented. The pressure sensor was fabricated to work under low voltage conditions by using a high mobility amorphous indium-gallium-zinc oxide (a-IGZO) thin-film transistor (TFT) and a stretched polyvinylidene fluoride (PVDF) film. To prepare a stable sensor suitable for practical use, we designed a device structure that shields ambient noise by grounding the control gate. The shielding structure significantly improves the stability of the device. Moreover, the sensor was fabricated on a flexible substrate and delaminated via a laser lift-off (LLO) technique to meet the urgent needs for flexibility. The pressure sensor showed good sensitivity and reliability over a pressure ranging from 0 to 75 kPa which covers the human touch pressure range. Especially, good linearity over a wide pressure range and high stability over 1000 repeated loadings were realized. Due to the simple structure, the pressure sensor demonstrates the advantage of being inexpensive to be manufactured and holds the potential to be integrated into the display backplane. Therefore, the proposed sensor has great potential in the production of flexible touch screens, human-machine interacting applications, and even electronic skins in the future.
| S-EPMC9301630 | biostudies-literature
Project description:This paper presents flexible pressure sensors based on free-standing and biodegradable glycine-chitosan piezoelectric films. Fabricated by the self-assembly of biological molecules of glycine within a water-based chitosan solution, the piezoelectric films consist of a stable spherulite structure of ?-glycine (size varying from a few millimeters to 1 cm) embedded in an amorphous chitosan polymer. The polymorphic phase of glycine crystals in chitosan, evaluated by X-ray diffraction, confirms formation of a pure ferroelectric phase of glycine (?-phase). Our results show that a simple solvent-casting method can be used to prepare a biodegradable ?-glycine/chitosan-based piezoelectric film with sensitivity (?2.82 ± 0.2 mV kPa-1) comparable to those of nondegradable commercial piezoelectric materials. The measured capacitance of the ?-glycine/chitosan film is in the range from 0.26 to 0.12 nF at a frequency range from 100 Hz to 1 MHz, and its dielectric constant and loss factor are 7.7 and 0.18, respectively, in the high impedance range under ambient conditions. The results suggest that the glycine-chitosan composite is a promising new biobased piezoelectric material for biodegradable sensors for applications in wearable biomedical diagnostics.
| S-EPMC7146751 | biostudies-literature
Project description:Compliance sensation is a unique feature of the human skin that electronic devices could not mimic via compact and thin form-factor devices. Due to the complex nature of the sensing mechanism, up to now, only high-precision or bulky handheld devices have been used to measure compliance of materials. This also prevents the development of electronic skin that is fully capable of mimicking human skin. Here, we developed a thin sensor that consists of a strain sensor coupled to a pressure sensor and is capable of identifying compliance of touched materials. The sensor can be easily integrated into robotic systems due to its small form factor. Results showed that the sensor is capable of classifying compliance of materials with high sensitivity allowing materials with various compliance to be identified. We integrated the sensor to a robotic finger to demonstrate the capability of the sensor for robotics. Further, the arrayed sensor configuration allows a compliance mapping which can enable humanlike sensations to robotic systems when grasping objects composed of multiple materials of varying compliance. These highly tunable sensors enable robotic systems to handle more advanced and complicated tasks such as classifying touched materials.
| S-EPMC7260970 | biostudies-literature