Improving heat and mass transfer rates through continuous drop-wise condensation.
Ontology highlight
ABSTRACT:
SUBMITTER: Alshehri A
PROVIDER: S-EPMC8490593 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:In the present paper, a thorough review of the experimental and numerical studies dealing with filmwise and dropwise condensation under microgravity is reported, covering mechanisms both inside tubes and on plain or enhanced surfaces. The gravity effect on the condensation heat transfer is examined considering the results of studies conducted both in terrestrial environment and in the absence of gravity. From the literature, it can be inferred that the influence of gravity on the condensation heat transfer inside tubes can be limited by increasing the mass flux of the operating fluid and, at equal mass flux, by decreasing the channel diameter. There are flow conditions at which gravity does exert a negligible effect during in-tube condensation: predictive tools for identifying such conditions and for the evaluation of the condensation heat transfer coefficient are also discussed. With regard to dropwise condensation, if liquid removal depends on gravity, this prevents its application in low gravity space systems. Alternatively, droplets can be removed by the high vapor velocity or by passive techniques based on the use of condensing surfaces with wettability gradients or micrometric/nanometric structuration: these represent an interesting solution for exploiting the benefits of dropwise condensation in terms of heat transfer enhancement and equipment compactness in microgravitational environments. The experimental investigation of the condensation heat transfer for long durations in steady-state zero-gravity conditions, such as inside the International Space Station, may compensate the substantial lack of repeatable experimental data and allow the development of reliable design tools for space applications.
| S-EPMC10073138 | biostudies-literature
Project description:Steam condensation is fundamental to several industrial processes, including power generation, desalination, and water harvesting. Lubricant-infused surfaces (LISs) promote sustained dropwise condensation, leading to significantly higher heat transfer performance that trades off with durability. Here, we present a systematic study on lubricant-infused copper tubes in a partial vacuum environment typical of power plant condensers to elucidate the influence of the design parameters-texturing, functionalizing agent, and lubricant viscosity-on condensation heat transfer performance and durability. Heat transfer effectiveness is introduced as a relevant parameter to quantify the effects of condensation heat transfer coefficient enhancement on the overall system heat transfer performance. Analytical expressions are developed for lubricant retention fraction and heat transfer effectiveness in terms of Bond number, viscosity ratio, and a dimensionless logarithmic mean temperature difference that can be used for predicting the performance of a LIS or for designing surfaces for a desired performance.
| S-EPMC8050781 | biostudies-literature
Project description:This paper is dedicated to the analysis of the improvement of heat transfer and the reduction of the pressure losses induced by the use of an active exchanger of millimeter size in a cooling loop. For pressure conditions imposed at the terminals of such a mini-channel whose upper wall is deformed by a progressive sinusoidal wave and for low Reynolds numbers (Re < 1000), we study the influence of the deformation parameters on the thermo-hydraulic performance of the exchanger (flow, heat transfer). The mechanical power applied to the deformed wall is connected to these parameters as well as to the pressure difference imposed by the external pump. The overall performance increases slightly with the value of the mechanical power up to a critical value for a given wall corrugation. Nevertheless, overall performance is up to 2 orders of magnitude higher than conventional static corrugated channels.
| S-EPMC6622530 | biostudies-literature
Project description:Vapor condensation is routinely used as an effective means of transferring heat or separating fluids. Dropwise condensation, where discrete droplets form on the condenser surface, offers a potential improvement in heat transfer of up to an order of magnitude compared to filmwise condensation, where a liquid film covers the surface. Low surface tension fluid condensates such as hydrocarbons pose a unique challenge since typical hydrophobic condenser coatings used to promote dropwise condensation of water often do not repel fluids with lower surface tensions. Recent work has shown that lubricant infused surfaces (LIS) can promote droplet formation of hydrocarbons. In this work, we confirm the effectiveness of LIS in promoting dropwise condensation by providing experimental measurements of heat transfer performance during hydrocarbon condensation on a LIS, which enhances heat transfer by ?450% compared to an uncoated surface. We also explored improvement through removal of noncondensable gases and highlighted a failure mechanism whereby shedding droplets depleted the lubricant over time. Enhanced condensation heat transfer for low surface tension fluids on LIS presents the opportunity for significant energy savings in natural gas processing as well as improvements in thermal management, heating and cooling, and power generation.
| S-EPMC5765152 | biostudies-literature
Project description:Recently, lubricant-impregnated surfaces (LIS) have emerged as a promising condenser surface by facilitating the removal of condensates from the surface. However, LIS has the critical limitation in that lubricant oil is depleted along with the removal of condensates. Such oil depletion is significantly aggravated under high condensation heat transfer. Here we propose a brushed LIS (BLIS) that can allow the application of LIS under high condensation heat transfer indefinitely by overcoming the previous oil depletion limit. In BLIS, a brush replenishes the depleted oil via physical contact with the rotational tube, while oil is continuously supplied to the brush by capillarity. In addition, BLIS helps enhance heat transfer performance with additional route to droplet removal by brush sweeping. By applying BLIS, we maintain the stable dropwise condensation mode for?>?48?hours under high supersaturation levels along with up to 61% heat transfer enhancement compared to hydrophobic surfaces.
| S-EPMC7031390 | biostudies-literature
Project description:Enhancing condensation heat transfer is important for broad applications from power generation to water harvesting systems. Significant efforts have focused on easy removal of the condensate, yet the other desired properties of low contact angles and high nucleation densities for high heat transfer performance have been typically neglected. In this work, we demonstrate immersion condensation on oil-infused micro and nanostructured surfaces with heterogeneous coatings, where water droplets nucleate immersed within the oil. The combination of surface energy heterogeneity, reduced oil-water interfacial energy, and surface structuring enabled drastically increased nucleation densities while maintaining easy condensate removal and low contact angles. Accordingly, on oil-infused heterogeneous nanostructured copper oxide surfaces, we demonstrated approximately 100% increase in heat transfer coefficient compared to state-of-the-art dropwise condensation surfaces in the presence of non-condensable gases. This work offers a distinct approach utilizing surface chemistry and structuring together with liquid-infusion for enhanced condensation heat transfer.
| S-EPMC3680863 | biostudies-other
Project description:Phase-change condensation is commonplace in nature and industry. Since the 1930s, it is well understood that vapor condenses in filmwise mode on clean metallic surfaces whereas it condenses by forming discrete droplets on surfaces coated with a promoter material. In both filmwise and dropwise modes, the condensate is removed when gravity overcomes pinning forces. In this work, we show rapid condensate transport through cracks that formed due to material shrinkage when a copper tube is coated with silica inverse opal structures. Importantly, the high hydraulic conductivity of the cracks promote axial condensate transport that is beneficial for condensation heat transfer. In our experiments, the cracks improved the heat transfer coefficient from ≈ 12 kW/m2 K for laminar filmwise condensation on smooth clean copper tubes to ≈ 80 kW/m2 K for inverse opal coated copper tubes; nearly a sevenfold increase from filmwise condensation and identical enhancement with state-of-the-art dropwise condensation. Furthermore, our results show that impregnating the porous structure with oil further improves the heat transfer coefficient by an additional 30% to ≈ 103 kW/m2 K. Importantly, compared to the fast-degrading dropwise condensation, the inverse opal coated copper tubes maintained high heat transfer rates when the experiments were repeated > 20 times; each experiment lasting 3-4 h. In addition to the new coating approach, the insights gained from this work present a strategy to minimize oil depletion during condensation from lubricated surfaces.
| S-EPMC8140112 | biostudies-literature
Project description:Bose-Einstein condensates (BECs) are macroscopic coherent matter waves that have revolutionized quantum science and atomic physics. They are important to quantum simulation1 and sensing2,3, for example, underlying atom interferometers in space4 and ambitious tests of Einstein's equivalence principle5,6. A long-standing constraint for quantum gas devices has been the need to execute cooling stages time-sequentially, restricting these devices to pulsed operation. Here we demonstrate continuous Bose-Einstein condensation by creating a continuous-wave (CW) condensate of strontium atoms that lasts indefinitely. The coherent matter wave is sustained by amplification through Bose-stimulated gain of atoms from a thermal bath. By steadily replenishing this bath while achieving 1,000 times higher phase-space densities than previous works7,8, we maintain the conditions for condensation. Our experiment is the matter wave analogue of a CW optical laser with fully reflective cavity mirrors. This proof-of-principle demonstration provides a new, hitherto missing piece of atom optics, enabling the construction of continuous coherent-matter-wave devices.
| S-EPMC9217748 | biostudies-literature
Project description:Heterogeneous surfaces with wetting contrast have gained extensive attention in recent years because of their potential application in condensation heat transfer enhancement. In this work, we engineered superhydrophobic/hydrophilic hybrid (SHH) surfaces on copper substrates via a laser-ablation process. We demonstrated that the as-fabricated SHH surfaces present dropwise condensation behavior; the condensate droplet growth, departure, and heat transfer performance depend strongly on the spacing of the hydrophilic spot. The surface with the hydrophilic spot spacing of 100 μm (SHH100) exhibits the most efficient dropwise condensation in terms of fast droplet growth rate, efficient coalescence-induced droplet departure, as well as enhanced heat transfer coefficient (HTC) compared to the homogeneous superhydrophobic (SHPo) surface. The mechanism underlying the enhanced condensation heat transfer performance is analyzed. A 12% enhancement on condensation HTC was found was found on SHH100 surface compared with the SHPo surface. Our results provide important insights for the design of hybrid surfaces with wetting contrast for enhancing condensation heat transfer performance in many industrial applications.
| S-EPMC7512437 | biostudies-literature
Project description:Enhancement in heat-transfer performance via dropwise condensation on superhydrophobic surfaces is much greater than that realized via generic condensation on a regular surface. However, if the supersaturation level during condensation increases above a specific value, water may seep to greater depths between structures. This may lead to attached condensation, which reduces condensation heat-transfer efficiency below that of ordinary surfaces. Therefore, it is critical to avoid the occurrence of supersaturation when superhydrophobic surfaces are employed in condenser design. The proposed study presents a simple method for regulating supersaturation on the laboratory scale. Experiments concerning droplet behavior on a superhydrophobic plate were performed to investigate droplet detachment and attachment in accordance with the surface and droplet temperatures. Results obtained have been represented as a ″droplet-behavior map″, which clearly depicts boundaries dividing the detachment and attachment regions. The supersaturation threshold obtained from the said map has been compared against results obtained from condensation heat-transfer experiments performed in an actual condenser environment. As observed, the two results demonstrate excellent agreement. Although superhydrophobicity of surfaces remains unchanged at room temperature, changes may occur in the extent of the supersaturation section, which improves condensation heat-transfer performance, depending on the surface-structure complexity. Therefore, droplet-behavior mapping has been used in this study to determine the available supersaturation section in accordance with the variation in surface roughness. Results confirm that the available supersaturation region increases with increasing surface roughness and structural complexity. Therefore, prior to applying superhydrophobicity to condensers, droplet-behavior mapping must be performed to avoid operation under the supersaturation conditions, which causes attached condensation.
| S-EPMC7643127 | biostudies-literature