CVD Synthesis of 3D-Shaped 3D Graphene Using a 3D-Printed Nickel–PLGA Catalyst Precursor
Ontology highlight
ABSTRACT:
SUBMITTER: Kondapalli V
PROVIDER: S-EPMC8567395 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:3D printing technology provides a unique platform for rapid prototyping of numerous applications due to its ability to produce low cost 3D printed platforms. Herein, a graphene-based polylactic acid filament (graphene/PLA) has been 3D printed to fabricate a range of 3D disc electrode (3DE) configurations using a conventional RepRap fused deposition moulding (FDM) 3D printer, which requires no further modification/ex-situ curing step. To provide proof-of-concept, these 3D printed electrode architectures are characterised both electrochemically and physicochemically and are advantageously applied as freestanding anodes within Li-ion batteries and as solid-state supercapacitors. These freestanding anodes neglect the requirement for a current collector, thus offering a simplistic and cheaper alternative to traditional Li-ion based setups. Additionally, the ability of these devices' to electrochemically produce hydrogen via the hydrogen evolution reaction (HER) as an alternative to currently utilised platinum based electrodes (with in electrolysers) is also performed. The 3DE demonstrates an unexpectedly high catalytic activity towards the HER (-0.46 V vs. SCE) upon the 1000th cycle, such potential is the closest observed to the desired value of platinum at (-0.25 V vs. SCE). We subsequently suggest that 3D printing of graphene-based conductive filaments allows for the simple fabrication of energy storage devices with bespoke and conceptual designs to be realised.
| S-EPMC5361393 | biostudies-literature
Project description:Polystyrene as a thin film on arbitrary substrates or pellets form defective graphene/graphitic films or powders that can be dispersed in water and organic solvents. The materials were characterized by visible absorption, Raman and X-ray photoelectron spectroscopy, electron and atomic force microscopy, and electrochemistry. Raman spectra of these materials showed the presence of the expected 2D, G, and D peaks at 2750, 1590, and 1350 cm-1, respectively. The relative intensity of the G versus the D peak was taken as a quantitative indicator of the density of defects in the G layer.
| S-EPMC6358832 | biostudies-literature
Project description:Three‑dimensional printed (3DP) scaffolds have become an excellent resource in alveolar bone regeneration. However, selecting suitable printable materials remains a challenge. In the present study, 3DP scaffolds were fabricated using three different ratios of poly (ε‑caprolactone) (PCL) and poly‑lactic‑co‑glycolic acid (PLGA), which were 0.1PCL/0.9PLGA, 0.5PCL/0.5PLGA and 0.9PCL/0.1PLGA. The surface characteristics and degradative properties of the scaffolds, and the response of human periodontal ligament stem cells (hPDLSCs) on the scaffolds, were assessed to examine the preferable ratio of PCL and PLGA for alveolar bone regeneration. The results demonstrated that the increased proportion of PLGA markedly accelerated the degradation, smoothed the surface and increased the wettability of the hybrid scaffold. Furthermore, the flow cytometry and Cell Counting Kit‑8 assay revealed that the adhesion and proliferation of hPDLSCs were markedlyincreased on the 0.5PCL/0.5PLGA and 0.1PCL/0.9PLGA scaffolds. Additionally, the alkaline phosphatase activity detection and reverse‑transcription quantitative polymerase chain reaction demonstrated that the hPDLSCs on the 0.5PCL/0.5PLGA scaffold exhibited the best osteogenic capacity. Consequently, PCL/PLGA composite scaffolds may represent a candidate focus for future bone regeneration studies, and the 0.5PCL/0.5PLGA scaffold demonstrated the best bio‑response from the hPDLSCs.
| S-EPMC6072152 | biostudies-literature
Project description:We propose a novel semiconductor compatible path for nano-graphene synthesis using precursors containing C-Br bonding and liquid catalyst. The unique combination of CBr4 as precursor and Ga as catalyst leads to efficient C precipitation at a synthesis temperature of 200 °C or lower. The non-wetting nature of liquid Ga on tested substrates limits nano-scale graphene to form on Ga droplets and substrate surfaces at low synthesis temperatures of T ≤ 450 °C and at droplet/substrate interfaces by C diffusion via droplet edges when T ≥ 400 °C. Good quality interface nano-graphene is demonstrated and the quality can be further improved by optimization of synthesis conditions and proper selection of substrate type and orientation. The proposed method provides a scalable and transfer-free route to synthesize graphene/semiconductor heterostructures, graphene quantum dots as well as patterned graphene nano-structures at a medium temperature range of 400-700 °C suitable for most important elementary and compound semiconductors.
| S-EPMC3983675 | biostudies-other
Project description:The hydrogenation of olefins, styrenes, enoates, imines, and sterically hindered tri-substituted olefins was accomplished using the pre-catalyst dilithiumbis(cycloocta-1,5-diene)nickelate(-II) (1). The mild conditions tolerate hydroxyl, halide, ester, and lactone functionalities. Mechanistic studies, including reaction progress analyses, poisoning experiments, and multinuclear NMR monitoring, indicate that a heterotopic (nickel nanoparticle) catalyst is in operation.
| S-EPMC7318650 | biostudies-literature
Project description:ObjectiveVascularization is a critical process during bone regeneration/repair and the lack of tissue vascularization is recognized as a major challenge in applying bone tissue engineering methods for cranial and maxillofacial surgeries. The aim of our study is to fabricate a vascular endothelial growth factor (VEGF)-loaded gelatin/alginate/β-TCP composite scaffold by 3D printing method using a computer-assisted design (CAD) model.MethodsThe paste, composed of (VEGF-loaded PLGA)-containing gelatin/alginate/β-TCP in water, was loaded into standard Nordson cartridges and promptly employed for printing the scaffolds. Rheological characterization of various gelatin/alginate/β-TCP formulations led to an optimized paste as a printable bioink at room temperature.ResultsThe in vitro release kinetics of the loaded VEGF revealed that the designed scaffolds fulfill the bioavailability of VEGF required for vascularization in the early stages of tissue regeneration. The results were confirmed by two times increment of proliferation of human umbilical vein endothelial cells (HUVECs) seeded on the scaffolds after 10 days. The compressive modulus of the scaffolds, 98±11MPa, was found to be in the range of cancellous bone suggesting their potential application for craniofacial tissue engineering. Osteoblast culture on the scaffolds showed that the construct supports cell viability, adhesion and proliferation. It was found that the ALP activity increased over 50% using VEGF-loaded scaffolds after 2 weeks of culture.SignificanceThe 3D printed gelatin/alginate/β-TCP scaffold with slow releasing of VEGF can be considered as a potential candidate for regeneration of craniofacial defects.
| S-EPMC6013845 | biostudies-literature
Project description:Designing 3D printed micro-architectures using electronic materials with well-understood electronic transport within such structures will potentially lead to accessible device fabrication for 'on-demand' applications. Here we show controlled nozzle-extrusion based 3D printing of a commercially available nano-composite of graphene/polylactic acid, enabling the fabrication of a tensile gauge functioning via the readjustment of the electron-tunneling barrier width between conductive graphene-centers. The electronic transport in the graphene/polymer 3D printed structure exhibited the Fowler Nordheim mechanism with a tunneling width of 0.79-0.95 nm and graphene centers having a carrier concentration of 2.66?×?1012/cm2. Furthermore, a mechanical strain that increases the electron-tunneling width between graphene nanostructures (~?38 nm) by only 0.19 ? reduces the electron flux by 1e/s/nm2 (from 18.51 to 19.51 e/s/nm2) through the polylactic acid junctions in the 3D-printed heterostructure. This corresponds to a sensitivity of 2.59 ?/?%, which compares well with other tensile gauges. We envision that the proposed electron-tunneling model for conductive 3D-printed structures with thermal expansion and external strain will lead to an evolution in the design of next-generation of 'on-demand' printed electronic and electromechanical devices.
| S-EPMC7347914 | biostudies-literature
Project description:Traumas and chronic damages can hamper the regenerative power of nervous, muscle, and connective tissues. Tissue engineering approaches are promising therapeutic tools, aiming to develop reliable, reproducible, and economically affordable synthetic scaffolds which could provide sufficient biomimetic cues to promote the desired cell behaviour without triggering graft rejection and transplant failure. Here, we used 3D-printing to develop 3D-printed scaffolds based on either PLA or graphene@PLA with a defined pattern. Multiple regeneration strategies require a specific orientation of implanted and recruited cells to perform their function correctly. We tested our scaffolds with induced pluripotent stem cells (iPSC), neuronal-like cells, immortalised fibroblasts and myoblasts. Our results demonstrated that the specific "lines and ridges" 100 µm-scaffold topography is sufficient to promote myoblast and fibroblast cell alignment and orient neurites along with the scaffolds line pattern. Conversely, graphene is critical to promote cells differentiation, as seen by the iPSC commitment to neuroectoderm, and myoblast fusions into multinuclear myotubes achieved by the 100 µm scaffolds containing graphene. This work shows the development of a reliable and economical 3D-printed scaffold with the potential of being used in multiple tissue engineering applications and elucidates how scaffold micro-topography and graphene properties synergistically control cell differentiation.
| S-EPMC8836229 | biostudies-literature
Project description:Chemistry digitization requires an unambiguous link between experiments and the code used to generate the experimental conditions and outcomes, yet this process is not standardized, limiting the portability of any chemical code. What is needed is a universal approach to aid this process using a well-defined standard that is composed of syntheses that are employed in modular hardware. Herein we present a new approach to the digitization of organic synthesis that combines process chemistry principles with 3D printed reactionware. This approach outlines the process for transforming unit operations into digitized hardware and well-defined instructions that ensure effective synthesis. To demonstrate this, we outline the process for digitizing 3 MIDA boronate building blocks, an ester hydrolysis, a Wittig olefination, a Suzuki-Miyaura coupling reaction, and synthesis of the drug sulfanilamide.
| S-EPMC9186708 | biostudies-literature
Project description:We describe the development of Lewis acid (LA) catalyst-impregnated 3D-printed stirrer devices and demonstrate their ability to facilitate the rapid screening of reaction conditions to synthesize heterocycles. The stereolithography 3D-printed stirrer devices were designed to fit round-bottomed flasks and Radleys carousel tubes using our recently reported solvent-resistant resin, and using CFD modeling studies and experimental data, we demonstrated that the device design leads to rapid mixing and rapid throughput over the device surface. Using a range of LA 3D-printed stirrers, the reaction between a diamine and an aldehyde was optimized for the catalyst and solvent, and we demonstrated that use of the 3D-printed catalyst-embedded devices led to higher yields and reduced reaction times. A library of benzimidazole and benzothiazole compounds were synthesized, and the use of devices led to efficient formation of the product as well as low levels of the catalyst in the resultant crude mixture. The use of these devices makes the process of setting up multiple reactions simpler by avoiding weighing out of catalysts, and the devices, once used, can be simply removed from the reaction, making the process of compound library synthesis more facile.
| S-EPMC10729026 | biostudies-literature