Synthesis of cobalt oxides thin films fractal structures by laser chemical vapor deposition.
Ontology highlight
ABSTRACT:
SUBMITTER: Haniam P
PROVIDER: S-EPMC3930193 | biostudies-other | 2014
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Polyaniline (PANI) is synthesized via oxidative chemical vapor deposition (oCVD) using aniline as monomer and antimony pentachloride as oxidant. Microscopy and spectroscopy indicate that oCVD processing conditions influence the PANI film chemistry, oxidation, and doping level. Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS) indicate that a substrate temperature of 90 °C is needed to minimize the formation of oligomers during polymerization. Lower substrate temperatures, such as 25 °C, lead to a film that mostly includes oligomers. Increasing the oxidant flowrate to nearly match the monomer flowrate favors the deposition of PANI in the emeraldine state, and varying the oxidant flowrate can directly influence the oxidation state of PANI. Changing the reactor pressure from 700 to 35 mTorr does not have a significant effect on the deposited film chemistry, indicating that the oCVD PANI process is not concentration dependent. This work shows that oCVD can be used for depositing PANI and for effectively controlling the chemical state of PANI.
| S-EPMC5480348 | biostudies-literature
Project description:Ternary materials made up only from the lightweight elements boron, carbon, and nitrogen are very attractive due to their tunable properties that can be obtained by changing the relative elemental composition. However, most of the times, the synthesis requires to use up to three different precursor and very high temperatures for the synthesis. Moreover, the low reciprocal solubility of boron nitride and graphene often leads to BN-C composite materials due to phase segregation. Herein, an innovative method is presented to prepare BCN thin films by chemical vapor deposition from a single source precursor, melamine diborate. The deposition occurs homogenously at relatively low temperatures generating very high degree of sp2 conjugation. The as-prepared thin films possess high transparency and refractive index values in the visible range that are of interest for reflective mirrors and lenses. Furthermore, they are wide-bandgap semiconductor with very positive valence band, making these materials very stable against oxidation of interest as protective coating and charge transport layer for solar cells. The simple chemical vapor deposition method that relies on commonly available and low-hazard precursor can open the way for application of BCN thin films in optics, optoelectronics, and beyond.
| S-EPMC8425861 | biostudies-literature
Project description:Control over thin film growth (e.g., crystallographic orientation and morphology) is of high technological interest as it affects several physicochemical material properties, such as chemical affinity, mechanical stability, and surface morphology. The effect of process parameters on the molecular organization of perfluorinated polymers deposited via initiated chemical vapor deposition (iCVD) has been previously reported. We showed that the tendency of poly(1H,1H,2H,2H-perfluorodecyl acrylate) (pPFDA) to organize in an ordered lamellar structure is a function of the filament and substrate temperatures adopted during the iCVD process. In this contribution, a more thorough investigation of the effect of such parameters is presented, using synchrotron radiation grazing incidence and specular X-ray diffraction (GIXD and XRD) and atomic force microscopy (AFM). The parameters influencing the amorphization, mosaicity, and preferential orientation are addressed. Different growth regimes were witnessed, characterized by a different surface structuring and by the presence of particular crystallographic textures. The combination of morphological and crystallographic analyses allowed the identification of pPFDA growth possibilities between island or columnar growth.
| S-EPMC6096450 | biostudies-literature
Project description:Degenerately doped ZnO is seen as a potential substitute to the ubiquitous and expensive Sn doped In2O3 as a transparent electrode in optoelectronic devices. Here, highly conductive and transparent Ga doped ZnO thin films were grown via aerosol assisted chemical vapor deposition. The lowest resistivity (7.8 × 10-4 Ω.cm) and highest carrier concentration (4.23 × 1020 cm-3) ever reported for AACVD grown ZnO: Ga was achieved due to using oxygen poor growth conditions enabled by diethylzinc and triethylgallium precursors.
| S-EPMC6971236 | biostudies-literature
Project description:Extrinsically doped ZnO thin films are of interest due to their high electrical conductivity and transparency to visible light. In this study, P doped ZnO thin films were grown on glass substrates via aerosol assisted chemical vapour deposition. The results show that P is a successful dopant for ZnO in the V+ oxidation state and is able to reduce resistivity to 6.0 × 10-3 Ω cm while maintaining visible light transmittance at ∼75%. The thins films were characterized by X-ray diffraction studies that showed only Bragg peaks for the wurtzite ZnO phase. Fitting of the diffraction data to a Le Bail model also showed a general expansion of the ZnO unit cell upon doping due to the substitution of Zn2+ ions with the larger P5+.
| S-EPMC9056824 | biostudies-literature
Project description:Misfit cobaltates ([Bi/Ba/Sr/Ca/CoO]n(RS)[CoO2]q) constitute the most promising family of thermoelectric oxides for high temperature energy harvesting. However, their complex structure and chemical composition makes extremely challenging their deposition by high-vacuum physical techniques. Therefore, many of them have not been prepared as thin films until now. Here we report the synthesis of high-quality epitaxial thin films of the most representative members of this family of compounds by a water-based chemical solution deposition method. The films show an exceptional crystalline quality, with an electrical conductivity and thermopower comparable to single crystals. These properties are linked to the epitaxial matching of the rock-salt layers of the structure to the substrate, producing clean interfaces free of amorphous phases. This is an important step forward for the integration of these materials with complementary n-type thermoelectric oxides in multilayer nanostructures.
| S-EPMC4495387 | biostudies-literature
Project description:ZnO based transparent conducting oxides are important as they provide an alternative to the more expensive Sn : In2O3 that currently dominates the industry. Here, we investigate B-doped ZnO thin films grown via aerosol assisted chemical vapour deposition. B : ZnO films were produced from zinc acetate and triethylborane using either tetrahydrofuran or methanol (MeOH) as the solvent. The lowest resistivity of 5.1 × 10-3 Ω cm along with a visible light transmittance of ∼75-80% was achieved when using MeOH as the solvent. XRD analysis only detected the wurtzite phase of ZnO suggesting successful solid solution formation with B3+ substituting Zn2+ sites in the lattice. Refinement of the XRD patterns showed minimal distortion to the ZnO unit cell upon doping when MeOH was the solvent due to the immiscibility of the [BEt3] solution (1.0 M solution in hexane) in methanol that limited the amount of B going into the films, thus preventing excessive doping.
| S-EPMC9671099 | biostudies-literature
Project description:Intensive research of hybrid metal-halide perovskite materials for use as photoactive materials has resulted in an unmatched increase in the power conversion efficiency of perovskite photovoltaics (PVs) over the last couple of years. Now that lab-fabricated perovskite devices rival the efficiency of silicon PVs, the next challenge of scalable mass manufacturing of large perovskite PV panels remains to be solved. For that purpose, it is still unclear which manufacturing method will provide the lowest processing cost and highest quality solar cells. Vapor deposition has been proven to work well for perovskites as a controllable and repeatable thin-film deposition technique but with processing speeds currently too slow to adequately lower the production costs. Addressing this challenge, in the present work, we demonstrate a high-speed vapor transport processing technique in a custom-built reactor that produces high-quality perovskite films with unprecedented deposition speed exceeding 1 nm/s, over 10× faster than previous vapor deposition demonstrations. We show that the semiconducting perovskite films produced with this method have excellent crystallinity and optoelectronic properties with 10 ns charge carrier lifetime, enabling us to fabricate the first photovoltaic devices made by perovskite vapor transport deposition. Our experiments are guided by computational fluid dynamics simulations that also predict that this technique could lead to deposition rates on the order of micrometers per second. This, in turn, could enable cost-effective scalable manufacturing of the perovskite-based solar technologies.
| S-EPMC6748557 | biostudies-literature
Project description:In this work, we demonstrate that ultraviolet (UV) laser photolysis of hydrocarbon species alters the flame chemistry such that it promotes the diamond growth rate and film quality. Optical emission spectroscopy and laser-induced fluorescence demonstrate that direct UV laser irradiation of a diamond-forming combustion flame produces a large amount of reactive species that play critical roles in diamond growth, thereby leading to enhanced diamond growth. The diamond growth rate is more than doubled, and diamond quality is improved by 4.2%. Investigation of the diamond nucleation process suggests that the diamond nucleation time is significantly shortened and nondiamond carbon accumulation is greatly suppressed with UV laser irradiation of the combustion flame in a laser-parallel-to-substrate geometry. A narrow amorphous carbon transition zone, averaging 4?nm in thickness, is identified at the film-substrate interface area using transmission electron microscopy, confirming the suppression effect of UV laser irradiation on nondiamond carbon formation. The discovery of the advantages of UV photochemistry in diamond growth is of great significance for vastly improving the synthesis of a broad range of technically important materials.
| S-EPMC6060054 | biostudies-literature
Project description:The use of hafnia (HfO2) has facilitated recent advances in high-density microchips. However, the low deposition rate, poor controllability, and lack of systematic research on the growth mechanism limit the fabrication efficiency and further development of HfO2 films. In this study, the high-throughput growth of HfO2 films was realized via laser chemical vapor deposition using a laser spot with a large gradient temperature distribution (100 K mm-1), in order to improve the experimental efficiency and controllability of the entire process. HfO2 films fabricated by a single growth process could be divided into four regions with different morphologies, and discerned for deposition temperatures increasing from 1300 K to 1600 K. The maximum deposition rate reached 362 μm h-1, which was 102 to 104 times higher than that obtained using existing deposition methods. The dielectric constants of high-throughput HfO2 films were in the range of 16-22, which satisfied the demand of replacing the traditional SiO2 layer for a new generation of microchips.
| S-EPMC9125986 | biostudies-literature