Stress-strain behavior of cementitious materials with different sizes.
Ontology highlight
ABSTRACT:
SUBMITTER: Zhou J
PROVIDER: S-EPMC3972930 | biostudies-other | 2014
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Extrusion based additive manufacturing of cementitious materials has demonstrated strong potential to become widely used in the construction industry. However, the use of this technique in practice is conditioned by a feasible solution to implement reinforcement in such automated process. One of the most successful ductile materials in civil engineering, strain hardening cementitious composites (SHCC) have a high potential to be employed for three-dimensional printing. The match between the tailored brittle matrix and ductility of the fibres enables these composites to develop multiple cracks when loaded under tension. Using previously developed mixtures, this study investigates the physical and mechanical performance of printed SHCC. The anisotropic behavior of the materials is explored by means of mechanical tests in several directions and micro computed tomography tests. The results demonstrated a composite showing strain hardening behavior in two directions explained by the fibre orientation found in the printed elements. Moreover, the printing technique used also has guaranteed an enhanced bond in between the printed layers.
| S-EPMC7287622 | biostudies-literature
Project description:It is commonly accepted that twinning can induce an increase of strain-hardening rate during the tensile process of face-centered cubic (FCC) metals and alloys with low stacking fault energy (SFE). In this study, we explored the grain size effect on the strain-hardening behavior of a Cu-15 at.%Al alloy with low SFE. Instead of twinning, we detected a significant contribution of stacking faults (SFs) irrespective of the grain size even in the initial stage of tensile process. In contrast, twinning was more sensitive to the grain size, and the onset of deformation twins might be postponed to a higher strain with increasing the grain size. In the Cu-15 at.%Al alloy with a mean grain size of 47 μm, there was a stage where the strain-hardening rate increases with strain, and this was mainly induced by the SFs instead of twinning. Thus in parallel with the TWIP effect, we proposed that SFs also contribute significantly to the plasticity of FCC alloys with low SFE.
| S-EPMC4652229 | biostudies-other
Project description:Chemicals and synthetic coatings are widely used to protect steel against corrosion. Bio-based corrosion inhibition strategies can be an alternative in the arising bioeconomy era. To maintain the good state of steel reinforcement in cracked concrete, microbe-based self-healing cementitious composites (MSCC) have been developed. Yet, proposed strategies involve reasonably slow crack filling by biomineralization and thus risk the possible rebar corrosion during crack healing. Here we upgrade the rebar protection to a higher level by combining MSCC with microbial induced corrosion inhibition. Presented NO3- reducing bacterial granules inhibit rebar corrosion by producing the anodic corrosion inhibitor NO2- and meanwhile heal a 300-µm-wide crack in 28 days. During 120 days exposure to 0.5?M Cl- solution, the rebars in cracked MSCC keep showing open circuit potentials above the critical value of -250 mV and they lose less than 2% of the total rebar material which corresponds to half the material loss in cracked plain mortar. Overall, the obtained rebar protection performance is comparable with that of uncracked mortar and mortar containing chemical inhibitor, hence the microbe-based system becomes an alternative to the traditional methods.
| S-EPMC6148264 | biostudies-literature
Project description:Rheological properties of cementitious suspensions are affected not only by their mixture composition but also by process-related factors such as shear history. To enable a model-based description, investigations were carried out on the effect of shear history (shear rate variation over time) on the cement paste agglomeration state. Therefore, a Focused Beam Reflectance Measurement (FBRM) system and a wide gap rheometer were coupled to study the relation between shear history and in-situ chord length distribution simultaneously, indicating particle agglomeration. Hence, the effect of average shear rates (resulting from the applied shear profile), as well as shear rate distribution within the gap (local shear rates) on the particle agglomeration state have been investigated. The rheological properties of cement paste were evaluated with the Reiner-Riwlin approach. Furthermore, the agglomeration state of the particles was compared for different average shear rates and local shear rates at various positions of the FBRM probe. The results show that the median chord length increases in all positions when the average shear rate is decreased, indicating increasing particle agglomeration. Moreover, due to variable local shear rates at different FBRM probe positions, different agglomeration states are observed, resulting from two factors, shear rate dependent particle agglomeration and shear-induced particle migration.
| S-EPMC7254234 | biostudies-literature
Project description:Microcystis blooms have become a ubiquitous phenomenon in freshwater ecosystems, and the size of Microcystis colonies varies widely throughout the year. In the present study, hydrogen peroxide (H?O?) was applied to test the effect of this algaecide on Microcystis colonies of different sizes and to evaluate the colonies' antioxidant strategy. The results showed that Microcystis populations collapsed under treatment with 5 mg/L H?O? at colony sizes smaller than 25 ?m. A dosage of 20 mg/L H?O? was necessary to efficiently control Microcystis colonies larger than 25 ?m. The enzymatic and non-enzymatic antioxidant systems of different colonies exhibited various strategies to mitigate oxidative stress. In small colonies, superoxide dismutase (SOD) activity was readily stimulated and operated with catalase (CAT) activity to eliminate reactive oxygen species (ROS). In colonies larger than 25 ?m, the antioxidant enzyme CAT and antioxidant substance glutathione (GSH) played major roles in mitigating oxidative stress at H?O? concentrations below 20 mg/L. In addition, application of the algaecide led to the release of intracellular-microcystins (MCs), and oxidatively-driven MCs reached high concentrations when colony size was larger than 100 ?m. Algaecide control measures should be implemented before the formation of large colonies to limit the algaecide dosage and MC release.
| S-EPMC5666353 | biostudies-literature
Project description:Concrete is very sensitive to crack formation. As wide cracks endanger the durability, repair may be required. However, these repair works raise the life-cycle cost of concrete as they are labor intensive and because the structure becomes in disuse during repair. In 1994, C. Dry was the first who proposed the intentional introduction of self-healing properties in concrete. In the following years, several researchers started to investigate this topic. The goal of this review is to provide an in-depth comparison of the different self-healing approaches which are available today. Among these approaches, some are aimed at improving the natural mechanism of autogenous crack healing, while others are aimed at modifying concrete by embedding capsules with suitable healing agents so that cracks heal in a completely autonomous way after they appear. In this review, special attention is paid to the types of healing agents and capsules used. In addition, the various methodologies have been evaluated based on the trigger mechanism used and attention has been paid to the properties regained due to self-healing.
| S-EPMC5458958 | biostudies-other
Project description:Porous TiAl3 intermetallics were prepared by the thermal explosion (TE) and space holder method with different particle sizes of Ti and Al powders, and their reaction behaviors were investigated. The results showed that with the increase in the particle size of the Ti and Al powders, the interfacial contact between the particles decreased, resulting in low interfacial energy and reaction activity, making the process difficult to initiate. Meanwhile, the heat flow rose from 358.37 J/g to 730.17 J/g and 566.74 J/g due to the extension of the solid-liquid diffusion time. The TiAl3 structures obviously expanded, and the formation of connected pore channels promoted the porosity. Only when the Ti and Al particle sizes were both small did the solid-solid diffusion significantly appear. At the same time, the TE reaction weakened, so the product particles had no time to fully grow. This indicates that the particle size of the raw materials controlled the TE reaction process by changing the solid-liquid diffusion reaction time and the degree of solid-phase diffusion.
| S-EPMC8658783 | biostudies-literature
Project description:The effect of superabsorbent polymers (SAPs) on autogenous crack healing in cementitious materials with early-age cracking was investigated. SAP-containing samples exposed to wet/dry cycles showed better autogenous healing than those only exposed to wet conditions, as determined by water flow and compressive strength recovery tests. The water flow rates through cracks (380 ± 40 µm) in cement paste and cement mortar containing 1.0% SAP decreased by around 97.1-100% and 79.7-90.7%, respectively, after 14 cycles of healing compared to 1 cycle. Although the initial compressive strength decreased with SAP addition, it recovered somewhat after a 28-d healing period. Microscopy and spectroscopy results identified CaCO3 and/or calcium silicate hydrate (CSH) as the main healing products.
| S-EPMC7040729 | biostudies-literature
Project description:In recent years, advanced materials have attracted considerable interest in the field of temperature detection and sensing. This study examined the thermochromic properties of inorganic manganese violet (MV) with increasing temperature. According to the thermochromic test, the material was found to have reversible and irreversible color change properties. The MV pigment was then applied to cementitious material at ratios of 1%, 3%, and 5%. The mixed cement samples with MV pigment were heated in a furnace, and digital images were captured at each temperature interval to evaluate the changes in the color information on the surface of the specimen. The mixed samples exhibited an irreversible thermochromic change from dark violet to grayish green above 400 °C. At the critical temperature of 440 °C, the RGB values increased by approximately 22%-55%, 28%-68%, and 7%-25%, depending on the content of MV pigment. In Lab space, the L value increased by approximately 23%-60% at 440 °C. The a value completely changed from positive to negative, and the b value changed from negative to positive. All the values differed according to the content of MV pigment at room temperature but approached similar ranges at the critical temperature, irrespective of the amount of MV pigment. To assess the changes in their microstructure and composition, scanning electron microscopy and energy dispersive X-ray spectroscopy were performed on the samples exposed to temperatures ranging from room temperature to 450 °C.
| S-EPMC7078599 | biostudies-literature
Project description:This study aims to examine the mechanical, shrinkage and chemical properties of photocatalytic cementitious materials containing synthetic fibers and a shrinkage-reducing admixture (SRA). Two types of titanium dioxide (TiO2) powders and white Portland cement were considered along with ordinary Portland cement (OPC) as a control. Two types of synthetic fibers, i.e., glass and polyethylene (PE), and an SRA with contents varying from 0% to 3% were also considered. Using the TiO2 powders and the white Portland cement was effective in reducing the nitrogen oxides (NOx) concentration in cement composites. The use of PE fibers was more effective than glass fibers in terms of the mechanical properties, i.e., the compressive strength and tensile performance. With the addition of TiO2 powders and SRA or the replacement of OPC with white cement, the mechanical properties of the cement mortar generally deteriorated. The total shrinkage of the mortar could be reduced by incorporating the fibers at volume fractions greater than 1%, and the glass fiber was more effective than the PE fiber in this regard. The TiO2 powders had no significant impact on the shrinkage reduction of the cement mortar, whereas the SRA and the white Portland cement effectively reduced shrinkage. The addition of 3% SRA decreased the total shrinkage by 43%, while the replacement of the OPC with white cement resulted in a 20% reduction in the shrinkage.
| S-EPMC7216050 | biostudies-literature