A Biomechanical Comparison of Three 1.5-mm Plate and Screw Configurations and a Single 2.0-mm Plate for Internal Fixation of a Mandibular Condylar Fracture.
Ontology highlight
ABSTRACT:
SUBMITTER: Aquilina P
PROVIDER: S-EPMC4130755 | biostudies-other | 2014 Sep
REPOSITORIES: biostudies-other
Similar Datasets
Project description:PurposeThe present study aimed to evaluate the efficacy and stability of 2.0 mm Titanium plates in treatment of mandibular angle fractures.Materials and methodsA randomized, prospective study was carried out on 17 patients treated by ORIF with 2.0 mm titanium plates. Operative handling of the plate and clinical stability were qualitatively analyzed.ResultsThe 2.0 mm plate showed good intra-operative handling and adequate clinical stability with follow up of 6 months showing good soft tissue healing.ConclusionA single 2.0 mm titanium plate provides easy handling and adequate occlusal stability in the post-operative phase as compared to the traditional 2.5 mm plate without post-operative MMF.Electronic supplementary materialThe online version of this article (doi:10.1007/s12663-010-0128-2) contains supplementary material, which is available to authorized users.
| S-EPMC3177482 | biostudies-literature
Project description:BACKGROUND:Geriatric acetabular fractures require fixation with sufficient primary stability to allow for immediate full-weight bearing. Minimally-invasive procedures would be desirable in order to keep perioperative morbidity low. The purpose of this study was to compare the biomechanical strength of lag screw-only fixation of anterior column posterior hemi-transverse (ACPHT) acetabular fractures to standard anatomical plate fixation. METHODS:Standardized ACPHT fractures were created in fourth generation synthetic pelvis models and stabilized by either an anatomical buttress plate (n?=?4) or by a screw-only construct (n?=?4). In a validated setup, a cyclic loading protocol was applied with increasing axial force (3200?cycles, 175?N to 2250?N). Construct survival, acetabular fracture motion, and mode of failure were assessed. RESULTS:The median number of cycles needed until failure of the construct occurred was 2304?cycles (range, 2020 to 2675) in the plate fixation group and 3200?cycles (range, 3101 to 3200) for the screw fixation constructs (p?=?.003). With regard to energy absorbed until failure, the plate fixation group resisted to 1.57?×?106?N*cycles (range, 1.21?×?106 to 2.14?×?106) and the screw fixation group to 3.17?×?106?N*cycles (range, 2.92?×?106 to 3.17?×?106; p?=?.001). All plate fixation specimens failed with a break-out of the posterior-column screw in the quadrilateral wing of the anatomical plate within a maximum load of 1750?N while the screw fixation constructs all survived loading of at least 2100?N. Acetabular fracture gap motion, acetabular rim angle, and medial femoral head subluxation as measures of fracture displacement were all not different between the two groups (p?>?0.1). CONCLUSIONS:In this in vitro biomechanical study, screw-only fixation of an ACPHT acetabular fracture resulted in at least as good construct survival as seen for standard buttress plate fixation. Both methods resisted sufficiently to forces that would be expected under physiologic conditions.
| S-EPMC6346571 | biostudies-literature
Project description:Background:Common failure modes of dynamic hip screw are cut-out and lift-off. To minimize the latter, distal screws can be inserted in different orientations. However, the effectiveness remains controversial. The aim of this study was to biomechanically investigate the influence of distal screw orientation on construct stability. Methods:Thirty artificial generic long bones were assigned to three groups (n = 10) and fixed with two-hole dynamic hip screw-plates, inserting distal cortical screws with neutral parallel screw orientation (A), divergent screw orientation (B) or convergent screw orientation (C). Starting at 60 N, cyclic loading was applied to the implant tip perpendicular to the lag screw axis with progressive peak load increase at a rate of 0.002 N/cycle until failure. Parameters of interest were construct stiffness and machine actuator displacement after 250, 1000 and 5000 cycles, as well as cycles to failure. Results:Displacement after 250, 1000 and 5000 cycles was significantly higher in Group C than in Groups A and B, p < 0.01, whereas no significant differences were observed between Groups A and B, p = 0.20. Specimens in Group C failed after 11,584 [standard deviation (SD), 5924] cycles, significantly earlier than those in Groups A and B [A: 27,351 (SD, 12,509); B: 28,793 (SD, 14,764)], p ? 0.02. Cycles to failure were not significantly different between Groups A and B, p > 0.99. The translational potential of this article:Parallel or divergent distal screw insertion provides similar construct stability in terms of resistance to plate lift-off. In contrast, converging screw insertion leads to inferior stability and is not advisable from a biomechanical point of view.
| S-EPMC6718874 | biostudies-literature
Project description:The aim of the study was to evaluate the efficacy and complication rate with use of 2.0-mm titanium three-dimensional (3D) curved angle strut plate for mandibular angle fractures. Twenty cases requiring internal fixation of the mandibular angle by 2.0-mm titanium 3D curved angle strut plates were evaluated. Postoperative clinical and radiological analyses were done on 1st, 2nd, 4th, and 6th weeks, which included wound healing, transmitted movements, difficulty in function and occlusion, and neurosensory changes, if any. Reasonable level of success in terms of immediate jaw function was noted in all cases. Transient inferior alveolar nerve dysfunction was observed in three cases, which recovered gradually in 2 months, and surgical site infection was observed in two cases, which resolved with appropriate course of antibiotics and wound care. Fixation of mandibular angle fractures with a 2.0-mm titanium 3D curved angle strut plate is predictable, expeditious, and has less complication rate.
| S-EPMC4078121 | biostudies-other
Project description:The aim of this study was to make a comparison of the biomechanical behavior of four different internal fixation systems for mandibular angle fractures. A total of 40 polyurethane mandible replicas were employed with different fixation methods: group 1SP, one 2.0-mm four-hole miniplate; group 2PPL, two 2.0-mm four-hole parallel miniplates; group 3DP, one 3D 2.0-mm four-hole miniplate; and group 3DPP, one 3D 2.0-mm eight-hole miniplate. Each group was subjected to incisal or homolateral molar region loading. The load resistance values were measured at load application causing tip displacement of 1, 3, and 5 mm, and at the time at which the system achieves its maximum strength (MS). Means and standard deviations were compared among groups using analysis of variance and the Tukey test. Group 2PPL showed higher strength for all the displacements. For incisal loading, no statistically significant differences were found between groups 1SP, 3DP, and 3DPP. For molar loading, group 1SP and 3DPP showed statistically significant differences. For MS testing, group 1SP and 2PPL showed statistically significant differences in incisal loading; group 1SP and 3DP showed no statistically significant differences; and group 3DPP showed lower values of strength. Two parallel miniplates provide the most favorable mechanical behavior under the conditions tested.
| S-EPMC4428728 | biostudies-literature
Project description:Objective:To investigate the influence of plate and screw hole position on the stability of simulated radial fractures stabilized with a 1.5 mm condylar locking compression plate (LCP). Study Design:In vitro mechanical testing of paired cadaveric limbs. Sample Population:Paired radii (n = 7) stabilized with a 1.5 mm condylar LCP with an open screw hole positioned either proximal to (PG), or over (OG), a simulated small fracture gap. Methods:Constructs were cycled in axial compression at a simulated trot load until failure or a maximum of 200,000 cycles. Specimens that sustained 200,000 cycles without failure were then loaded in axial compression in a single cycle to failure. Construct cyclic axial stiffness and gap strain, fatigue life, and residual strength were evaluated and compared between constructs using analysis of variance. Results:Of pairs that had a failure during cyclic loading, OG constructs survived fewer cycles (54,700 ± 60,600) than PG (116,800 ± 49,300). OG constructs had significantly lower initial stiffness throughout cyclic loading and higher gap strain range within the first 1,000 cycles than PG constructs. Residual strength variables were not significantly different between constructs, however yield loads occurred at loads only marginally higher than approximated trot loads. Fatigue life decreased with increasing body weight. Conclusion:Fracture fixation stability is compromised by an open screw hole directly over a fracture gap compared to the open screw hole being buttressed by bone in the model studied. The 1.5 mm condylar LCP may be insufficient stabilization in dogs with appropriate radial geometry but high body weights.
| S-EPMC5975469 | biostudies-literature
Project description:BackgroundAlthough preventing triceps fragment displacement is essential for treating an olecranon fracture, we frequently encounter situations in which only a few screws can be fixed to the triceps fragment. The aim of this study was to compare the stability of double-plate fixation and posterior plate fixation for olecranon fractures when the triceps fragment was small and only 2 screws could be inserted.MethodsA composite ulna model was used to simulate olecranon fracture. Four groups were formed consisting of double-plate and posterior plates with cortical and locking screws. The cyclic loading test was conducted for 500 cyclic loads of 5 to 50 N on a specimen to measure micromotion and displacement of the gap caused by light exercise. The load-to-failure test was performed by applying a load until fixation loss, defined as when the fracture gap increased by 2 mm or more or catastrophic failure occurred, to measure the maximum load.ResultsEight samples per group were tested through the pilot study. All groups were stable with a micromotion of <0.5 mm. However, the mean micromotion showed significant differences between the 4 groups (P < .001, Table 1). In the mean micromotion during exercise, posterior plating with cortical screws was the most stable (0.09 ± 0.02 mm) while double-plating with cortical screws was the most unstable (0.42 ± 0.11 mm). At the maximum load, posterior plating with locking screws was the strongest (205.3 ± 2.8 N) while double-plating with cortical screws was the weakest (143.3 ± 27.1 N). There was no significant difference in displacement after light exercise between the groups.ConclusionsThis study showed that when 2 triceps screws were used, both groups were stable during light exercise, but posterior-plating was stronger than double-plating.
| S-EPMC8735719 | biostudies-literature
Project description:Vertical femoral neck fractures in patients younger than 65 years of age often require hip-conserving surgeries. However, traditional fixation strategies using three parallel cannulated screws often fail in such patients due to an unfavorable biomechanical environment. This study compared different cannulated screw fixation techniques in patients via patient-specific finite element analysis with linear tetrahedral (C3D4) elements. Forty vertical femoral neck fracture models were created based on computed tomography images obtained from eight healthy participants. Five different fixation strategies: alpha, buttress, rhomboid, inverted triangle, and triangle were assessed in walking status. Biomechanical parameters including stiffness, interfragmentary motion in two directions (detachment and shearing), compression force, and maximal implant stress were evaluated. The mean relative coefficient of strain distribution between the finite element analysis and experiment was from 0.78 to 0.94. Stiffness was highest (p < .05) in the buttress group (923.1 N/mm), while interfragmentary motion was lowest (p < .05) in the alpha group. Maximal stress was highest (p < .05) in the buttress group and lowest in the alpha group. Shearing values were significantly lower in the alpha group than in the rhomboid group (p = .004). Moreover, Shearing values were significantly higher (p = .027), while detachment values were significantly lower (p = .027), in the inverted triangle than in the triangle group. Clinical significance: Our results suggest that alpha fixation is the most reliable and biomechanically efficient strategy for young patients with vertical femoral neck fractures. Regular and inverted triangular fixation strategies may be suitable for fractures of different skeletal constructions due to antidetachment/shearing abilities.
| S-EPMC8451753 | biostudies-literature
Project description:BackgroundSacroiliac screw fixation in elderly patients with pelvic fractures is prone to failure owing to impaired bone quality. Cement augmentation has been proposed as a possible solution, because in other anatomic areas this has been shown to reduce screw loosening. However, to our knowledge, this has not been evaluated for sacroiliac screws.Questions/purposesWe investigated the potential biomechanical benefit of cement augmentation of sacroiliac screw fixation in a cadaver model of osteoporotic bone, specifically with respect to screw loosening, construct survival, and fracture-site motion.MethodsStandardized complete sacral ala fractures with intact posterior ligaments in combination with ipsilateral upper and lower pubic rami fractures were created in osteoporotic cadaver pelves and stabilized by three fixation techniques: sacroiliac (n = 5) with sacroiliac screws in S1 and S2, cemented (n = 5) with addition of cement augmentation, and transsacral (n = 5) with a single transsacral screw in S1. A cyclic loading protocol was applied with torque (1.5 Nm) and increasing axial force (250-750 N). Screw loosening, construct survival, and sacral fracture-site motion were measured by optoelectric motion tracking. A sample-size calculation revealed five samples per group to be required to achieve a power of 0.80 to detect 50% reduction in screw loosening.ResultsScrew motion in relation to the sacrum during loading with 250 N/1.5 Nm was not different among the three groups (sacroiliac: 1.2 mm, range, 0.6-1.9; cemented: 0.7 mm, range, 0.5-1.3; transsacral: 1.1 mm, range, 0.6-2.3) (p = 0.940). Screw subsidence was less in the cemented group (3.0 mm, range, 1.2-3.7) compared with the sacroiliac (5.7 mm, range, 4.7-10.4) or transsacral group (5.6 mm, range, 3.8-10.5) (p = 0.031). There was no difference with the numbers available in the median number of cycles needed until failure; this was 2921 cycles (range, 2586-5450) in the cemented group, 2570 cycles (range, 2500-5107) for the sacroiliac specimens, and 2578 cycles (range, 2540-2623) in the transsacral group (p = 0.153). The cemented group absorbed more energy before failure (8.2 × 105 N*cycles; range, 6.6 × 105-22.6 × 105) compared with the transsacral group (6.5 × 105 N*cycles; range, 6.4 × 105-6.7 × 105) (p = 0.016). There was no difference with the numbers available in terms of fracture site motion (sacroiliac: 2.9 mm, range, 0.7-5.4; cemented: 1.2 mm, range, 0.6-1.9; transsacral: 2.1 mm, range, 1.2-4.8). Probability values for all between-group comparisons were greater than 0.05.ConclusionsThe addition of cement to standard sacroiliac screw fixation seemed to change the mode and dynamics of failure in this cadaveric mechanical model. Although no advantages to cement were observed in terms of screw motion or cycles to failure among the different constructs, a cemented, two-screw sacroiliac screw construct resulted in less screw subsidence and greater energy absorbed to failure than an uncemented single transsacral screw.Clinical relevanceIn osteoporotic bone, the addition of cement to sacroiliac screw fixation might improve screw anchorage. However, larger mechanical studies using these findings as pilot data should be performed before applying these preliminary findings clinically.
| S-EPMC5052190 | biostudies-literature
Project description:BackgroundTarsometatarsal (TMT) arthrodesis is a common operative procedure for end-stage arthritis of the TMT joints. To date, there is no consensus on the best fixation technique for TMT arthrodesis and which joints should be included.MethodsThirty fresh-frozen feet were divided into one group (15 feet) in which TMT joints I-III were fused with a lag screw and locking plate and a second group (15 feet) in which TMT joints I-III were fused with 2 crossing lag screws. The arthrodesis was performed stepwise with evaluation of mobility between the metatarsal and cuneiform bones after every application or removal of a lag screw or locking plate.ResultsIsolated lag-screw arthrodesis of the TMT I-III joints led to significantly increased stability in every joint (P < .05). Additional application of a locking plate caused further stability in every TMT joint (P < .05). An additional crossed lag screw did not significantly increase rigidity of the TMT II and III joints (P > .05). An IM screw did not influence the stability of the fused TMT joints. For TMT III arthrodesis, lag-screw and locking plate constructs were superior to crossed lag-screw fixation (P < .05). TMT I fusion does not support stability after TMT II and III arthrodesis.ConclusionEach fixation technique provided sufficient stabilization of the TMT joints. Use of a lag screw plus locking plate might be superior to crossed screw fixation. An additional TMT I and/or III arthrodesis did not increase stability of an isolated TMT II arthrodesis.Clinical relevanceWe report the first biomechanical evaluation of TMT I-III arthrodesis. Our results may help surgeons to choose among osteosynthesis techniques and which joints to include in performing arthrodesis of TMT I-III joints.
| S-EPMC8772252 | biostudies-literature