Cytotoxicity Test of One-Step Self-Etching Bonding Agents by Standardized Dentin Barrier Test Using Polyurethane Discs.
Ontology highlight
ABSTRACT:
SUBMITTER: Kim MJ
PROVIDER: S-EPMC5453160 | biostudies-other | 2013 Dec
REPOSITORIES: biostudies-other
Similar Datasets
Project description:This study evaluated an experimental two-step self-etch adhesive (BZF-29, BZF) by comparing it with a reference two-step self-etch adhesive (Clearfil Megabond 2, MB) and a universal adhesive (G-Premio Bond, GP) for microtensile bond strength (μTBS) and resin-dentin interfacial characteristics. Twenty-four human third molars were used for the μTBS test. Bonded peripheral dentin slices were separated to observe the resin-dentin interface and measure the adhesive layer thickness with SEM. μTBS data of the central beams were obtained after 24 h and 6 months of water storage. Fracture modes were determined using a stereomicroscope and SEM. Nine additional third molars were used to determine the elastic modulus (E) employing an ultra microhardness tester. Water storage did not affect μTBS of the tested adhesives (p > 0.05). μTBS of BZF and MB were similar but significantly higher than GP (p < 0.05). BZF achieved the highest adhesive layer thickness, while GP the lowest. E of BZF and MB were comparable but significantly lower than GP (p < 0.05). Except for GP, the predominant fracture mode was nonadhesive. The superior bonding performance of BZF and MB could be attributed to their better mechanical property and increased adhesive thickness imparting better stress relief at the interface.
| S-EPMC8036260 | biostudies-literature
Project description:The present study examined the mechanism for caries resistance and the pulp responses in vital teeth following the use of the augmented-pressure adhesive displacement technique. Dentin adhesives were applied to the surface of sound dentin disks in 4 experimental groups: non-antibacterial adhesive and gentle adhesive displacement (N-G), non-antibacterial adhesive and augmented-pressure adhesive displacement (N-H), antibacterial adhesive and gentle adhesive displacement (A-G), antibacterial adhesive and augmented-pressure adhesive displacement (A-H). The depth of demineralization induced by biological or chemical demineralization models was measured using confocal laser scanning microscopy and analyzed with two-way ANOVA. Pulp responses of vital dog's teeth to the augmented-pressure adhesive displacement technique were evaluated using light microscopy. Depth of demineralization was significantly affected by "adhesive type" and "intensity of adhesive displacement" for biological demineralization. For chemical demineralization, only "intensity of adhesive displacement" showed significant influence on lesion depth. Pulp response of 0.1, 0.2 and 0.3?MPa groups showed only moderate disorganization of the odontoblast layer at 24?hours that completely re-organized after 3 weeks. Augmented-pressure adhesive displacement improves the caries resistance property of bonded dentin and does not cause irreversible pulpal damage to vital teeth when the air pressure employed is equal or smaller than 0.3?MPa.
| S-EPMC5013435 | biostudies-literature
Project description:ObjectivesSurface conditioning of enamel and dentin is a key step during adhesive restorative procedures and strategies. The aim of this study was to investigate the effectiveness of five α-hydroxy-acids (AHAs) as enamel and dentin surface etchants.MethodsEnamel and dentin specimens were prepared from human molars to determine the depth of demineralization by optical profilometry (Δz), the resin bond strength to enamel and dentin (μTBS), the micro-permeability of dentin-resin interfaces, and the gelatinolytic activity of dentin matrix induced by AHAs [glycolic (GA), lactic (LA), citric (CA), malic (MI) and tartaric (TA)] and controls [phosphoric (PA) and maleic (MA)]. All acids were prepared at 35% concentration. Adhesion studies employed Adper Single Bond Plus bonding system. Data were individually processed and analyzed by ANOVA, post-hoc tests and Pearson correlations (α = 0.05).ResultsAHA exhibited statistically lower depth of demineralization of enamel and dentin (average 4 fold) than controls (p < 0.001). In enamel, MA and PA etching resulted in higher μTBS than AHA groups (p < 0.001). In dentin, GA, TA, CI and LA etching resulted in statistically similar μTBS than PA (p < 0.05). The hybrid-layer (HL) thickness and interfacial micro-permeability intensity were statistically lower for AHA groups (p < 0.05). A significant positive correlation was observed between the intensity of micro-permeability and the thickness of HL (p < 0.05). AHA etchants elicited lower dentin enzymatic activity than controls (p < 0.05).SignificanceAHAs effectively etched enamel and dentin surfaces. In particular, GA and TA resulted in suitable μTBS and sealing ability as well as induced less gelatinolytic activity in dentin than PA and MA.
| S-EPMC6513690 | biostudies-literature
Project description:The achievement of a strong and stable bond between composite resin and dentin remains a challenge in restorative dentistry. Over the past two decades, dental materials have been substantially improved, with better handling and bonding characteristics. However, little attention has been paid to the contribution of collagen structure/stability to bond strength. We hypothesized that the induction of cross-linking in dentin collagen improves dentin collagen stability and bond strength. This study investigated the effects of glutaraldehyde-and grape seed extract-induced cross-linking on the dentin bond strengths of sound and caries-affected dentin, and on the stability of dentin collagen. Our results demonstrated that the application of chemical cross-linking agents to etched dentin prior to bonding procedures significantly enhanced the dentin bond strengths of caries-affected and sound dentin. Glutaraldehyde and grape seed extract significantly increased dentin collagen stability in sound and caries-affected dentin, likely via distinct mechanisms.
| S-EPMC3318032 | biostudies-literature
Project description:The durability of the resin-dentin bonding interface is a key issue in clinical esthetic dentistry. Inspired by the extraordinary bioadhesive properties of marine mussels in a wet environment, we designed and synthetized N-2-(3,4-dihydroxylphenyl) acrylamide (DAA) according to the functional domain of mussel adhesive proteins. DAA's properties of collagen cross-linking, collagenase inhibition, inducing collagen mineralization in vitro, and as a novel prime monomer for clinical dentin adhesion use, its optimal parameters, and effect on the adhesive longevity and the bonding interface's integrity and mineralization, were evaluated in vitro and in vivo. The results showed that oxide DAA can inhibit the activity of collagenase and cross collagen fibers to improve the anti-enzymatic hydrolysis of collagen fibers and induce intrafibrillar and interfibrillar collagen mineralization. As a primer used in the etch-rinse tooth adhesive system, oxide DAA can improve the durability and integrity of the bonding interface by anti-degradation and mineralization of the exposed collagen matrix. Oxidized DAA (OX-DAA) is a promising primer for improving dentin durability; using 5% OX-DAA ethanol solution and treating the etched dentin surface for 30 s is the optimal choice when used as a primer in the etch-rinse tooth adhesive system.
| S-EPMC10079285 | biostudies-literature
Project description:This in vitro study was conducted to evaluate the shear bond strength of "non-self-adhesive" resin to dental zirconia etched with hydrofluoric acid (HF) at room temperature and to compare it to that of air-abraded zirconia. Sintered zirconia plates were air-abraded (control) or etched with 10%, 20%, or 30% HF for either 5 or 30 min. After cleaning, the surfaces were characterized using various analytical techniques. Three resin cylinders (Duo-Link) were bonded to each treated plate. All bonded specimens were stored in water at 37 °C for 24 h, and then half of them were additionally thermocycled 5000 times prior to the shear bond-strength tests (n = 12). The formation of micro- and nano-porosities on the etched surfaces increased with increasing concentration and application time of the HF solution. The surface wettability of zirconia also increased with increasing surface roughness. Higher concentrations and longer application times of the HF solution produced higher bond-strength values. Infiltration of the resin into the micro- and nano-porosities was observed by scanning electron microscopy. This in vitro study suggests that HF slowly etches zirconia ceramic surfaces at room temperature, thereby improving the resin-zirconia bond strength by the formation of retentive sites.
| S-EPMC5455444 | biostudies-other
Project description:Consistent and proper use of respiratory protective devices (RPD) is one of the essential actions that can be taken to reduce the risk of exposure to airborne hazards, i.e., biological and nonbiological aerosols, vapours, and gases. Proper fit of the facepiece and comfort properties of RPDs play a crucial role in effective protection and acceptance of RPDs by workers. The objective of the present paper was to develop viscoelastic polyurethane foams for use in RPD seals characterised by proper elasticity, allowing for the enhancement of the device fit to the face and the capability of removing moisture from the skin in order to improve the comfort of RPD use. Moreover, it was pivotal to ensure the non-flammability of the foams, as well as a simultaneous reduction in their cytotoxicity. The obtained foams were characterised using scanning electron microscopy, infrared spectroscopy, thermogravimetry, and differential scanning calorimetry. Measurements also involved gel fraction, apparent density, compression set, rebound resilience, wettability, flammability, and cytotoxicity. The results are discussed in the context of the impact of modifications to the foam formulation (i.e., flame-retardant type and content) on the desired foam properties. The test results set directions for future works aimed to develop viscoelastic polyurethane foams that could be applied in the design of respiratory protective devices.
| S-EPMC8746040 | biostudies-literature
Project description:The objective of this study is to replace a traditional methacrylate-based primer (glycine, N-(2-hydroxy-3-(2-methyl-1-oxo-2-propenyl)propyl)-N-(4-methylphenyl) monosodium salt, NTG-GMA) with a hydrolytically stable ether-based primer (glycine, N-2-hydroxy-3-(4-vinylbenzyloxy)-propyl-N-(4-methylphenyl), monosodium salt, NTG-VBGE). The performance and durability of bonding composites to detin of two primers combined with methacrylate-based or ether-based adhesives were evaluated using shear bond strength (SBS) and micro-tensile bond strength (μTBS) combined with thermal cycling. The hydrolysis resistance of NTG-VBGE against hydrolysis was tested by challenging primed hydroxyapatite crystals with an esterase. The hydrophilicity of the primers and the resin spreading kinetics of adhesives on primed dentin were characterized by water contact angle measurements. The new primer NTG-VBGE was found to be compatible with both methacrylate-based adhesives and ether-based adhesives. The highest μTBS values were found in the test group of NTG-VBGE and ether-based adhesive, which was consistent with the resin spreading kinetics results. The more hydrophobic and hydrolytically stable primer/adhesive achieved improved dentin infiltration and bonding strength, suggesting significant potential for further developing dental restorative materials with extended service life.
| S-EPMC9501844 | biostudies-literature
Project description:Purpose This study evaluated the combined effects of Carbodiimide (EDC) and ethanol–wet bonding (EWB) pretreatment on the bond strength and resin–dentin surface. Methods Phosphoric acid-etched dentin specimens were randomly divided into five groups based on the following pretreatments: deionized water (control), EWB, 0.3M EDC in water (EDCw), EDC water solution combined EWB (EDCw + EWB), and 0.3M EDC in ethanol (EDCe). A scanning electron microscope (SEM) was used to observe the morphology of collagen fibrils on the demineralized dentin matrix in each group after pretreatment. The adhesives Prime & Bond NT (PB) (Dentsply De trey, Konstanz, Germany) or Single bond 2 (SB) (3M ESPE, St. Paul, MN, USA) was applied after pretreatments, and a confocal laser scanning microscope (CLSM) was used to evaluate the quality of resin tags. The degree of conversion (DC) of the adhesive was investigated by Fourier transform infrared spectroscopy (ATR-FTIR). The dentin was first bonded with resin and bathed in water at 37 °C for 24 h. Half of them were subjected to 10, 000 cycles in a thermocycler between 5 °C and 55 °C before a microshear bond strength (µSBS) test. The statistical methods were Analysis of Variance (ANOVA) and a Tukey post hoc test at α = 0.05. Results The µSBS was significantly affected by pretreatments (p < 0.001), adhesives (p < 0.001), and aging conditions (p < 0.001) as revealed by the three-way ANOVA. The EDCw, EDCw + EWB, and EDCe groups significantly increased the µSBS; the EDCw + EWB and EDCe groups produced the highest µSBS. In the EDC-containing groups, the SEM showed at the collagen fibrils in the dentin matrix formed a three-dimensional network structure in the tubules after cross-linking into sheets, and the hybrid layer formed thicker resin tags under a CLSM. In the EDC-containing groups, the CLSM observed an increase in the length of resin tags. PB showed a higher DC and bonding strength than SB, and the five pretreatment groups tested did not affect the DC of the two adhesives. Conclusions In etch–and–rinse bonding system, EDC combined with EWB pretreatment can improve the quality of the hybrid layer and enhance the mechanical properties of demineralized dentin matrix. Pretreatment with EDC–ethanol solution may be a new clinically friendly option for enhancing dentin bonding durability.
| S-EPMC9590415 | biostudies-literature
Project description:BackgroundThis study aimed to evaluate the effect of dentin pretreatment by Dimethyl Sulfoxide (DMSO) on the bond strength and microleakage of a universal bonding agent to dentin.MethodsFifty-six dentinal discs (thickness = 2 mm) were obtained from the crowns of the human third molars. The disks were assigned into 4 groups and treated as follows; self-etch-control group: G-Premio universal adhesive was used in self-etch mode, total-etch-control: G-Premio universal adhesive was used in total-etch mode, self-etch-DMSO: Water-based DMSO (50% volume) was applied on the samples for 60 s followed by application of G-Premio universal adhesive in self-etch mode, and Total-etch-DMSO: The samples were etched, and then, water-based DMSO was applied on them for 60 s followed by the application of G-Premio universal adhesive in total-etch mode. Afterward, resin composite was placed on all samples and light-cured. The samples were kept in distilled water and subjected to 5000 thermal cycles. Microshear bond strength was measured using the universal testing machine and failure modes were analyzed using a stereomicroscope. Forty-eight human third molars were used for microleakage evaluation and a standardized class five cavity was prepared on the buccal surface of each tooth. The teeth were assigned into 4 groups and received aforementioned surface treatment and the cavities were filled with resin composite. After storing in water for 24 h, the samples were subjected to 5000 cycles of thermocycling and the microleakage level of the samples was evaluated using silver nitrate uptake at the bonded interface. Two-way ANOVA test was used to analyze the effect of bonding technique (self-etch/ total-etch) and DMSO pretreatment on the microshear bond strength and microleakage of G-Premio adhesive to dentin.ResultsBonding technique had no effect on the bond strength values (p = 0.17) while DMSO pretreatment significantly decreased the microshear bond strength of the samples (p = 0.001). DMSO application increased microleakage significantly in total-etch (P-value = 0.02) while it had no effect in self-etch mode (P-value = 0.44).ConclusionsPretreatment of dentin using 50% DMSO significantly reduced the bond strength of G-Premio Bond in both self-etch and total-etch modes. DMSO effect on microleakage depended on the etching technique; DMSO increased the microleakage level when the adhesive was used in total-etch mode while did not affect the microleakage in self-etch mode.
| S-EPMC10148491 | biostudies-literature