Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Isothermal Time-Temperature-Precipitation Diagram for an Aluminum Alloy 6005A by In Situ DSC Experiments.

ABSTRACT: Time-temperature-precipitation (TTP) diagrams deliver important material data, such as temperature and time ranges critical for precipitation during the quenching step of the age hardening procedure. Although the quenching step is continuous, isothermal TTP diagrams are often applied. Together with a so-called Quench Factor Analysis, they can be used to describe very different cooling paths. Typically, these diagrams are constructed based on mechanical properties or microstructures after an interrupted quenching, i.e., ex situ analyses. In recent years, an in situ calorimetric method to record continuous cooling precipitation diagrams of aluminum alloys has been developed to the application level by our group. This method has now been transferred to isothermal experiments, in which the whole heat treatment cycle was performed in a differential scanning calorimeter. The Al-Mg-Si-wrought alloy 6005A was investigated. Solution annealing at 540 °C and overcritical quenching to several temperatures between 450 °C and 250 °C were followed by isothermal soaking. Based on the heat flow curves during isothermal soaking, TTP diagrams were determined. An appropriate evaluation method has been developed. It was found that three different precipitation reactions in characteristic temperature intervals exist. Some of the low temperature reactions are not accessible in continuous cooling experiments and require isothermal studies.

SUBMITTER: Milkereit B

PROVIDER: S-EPMC5453356 | biostudies-other | 2014 Mar

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

Precipitation during Quenching in 2A97 Aluminum Alloy and the Influences from Grain Structure.

Project description:The quench-induced precipitation and subsequent aging response in 2A97 aluminum alloy was investigated based on the systematic microstructure characterization. Specifically, the influence on precipitation from grain structure was examined. The results indicated the evident influence from the cooling rate of the quenching process. Precipitation of T1 and δ' phase can hardly occur in the specimen exposed to water quenching while become noticeable in the case of air cooling. The yield strength of 2A97-T6 alloy de-graded by 234 MPa along with a comparable elongation when water quenching was replaced by air cooling. Sub-grains exhibited a much higher sensitivity to the precipitation during quenching. The presence of dislocations in sub-grains promoted the quench-induced precipitation by acting as nucleation sites and enhancing the diffusion of the solute. A quenching rate of 3 °C/s is tolerable for recrystallized grains in 2A97 Al alloy but is inadequate for sub-grains to inhibit precipitation. The study fosters the feasibility of alleviating quench-induced precipitation through cultivating the recrystallization structure in highly alloyed Al-Cu-Li alloys.

| S-EPMC8197508 | biostudies-literature

In-situ anodic precipitation process for highly efficient separation of aluminum alloys.

Project description:Electrorefining process has been widely used to separate and purify metals, but it is limited by deposition potential of the metal itself. Here we report in-situ anodic precipitation (IAP), a modified electrorefining process, to purify aluminium from contaminants that are more reactive. During IAP, the target metals that are more cathodic than aluminium are oxidized at the anode and forced to precipitate out in a low oxidation state. This strategy is fundamentally based on different solubilities of target metal chlorides in the NaAlCl4 molten salt rather than deposition potential of metals. The results suggest that IAP is able to efficiently and simply separate components of aluminum alloys with fast kinetics and high recovery yields, and it is also a valuable synthetic approach for metal chlorides in low oxidation states.

| S-EPMC8486879 | biostudies-literature

Effect of Non-Isothermal Aging on the Mechanical Properties and Corrosion Resistance of 2A12 Aluminum Alloy.

Project description:The effect of linear non-isothermal aging and composite non-isothermal aging on the mechanical properties and corrosion resistance of 2A12 aluminum alloy was investigated. Optical microscopy (OM) and scanning electron microscopy (SEM) equipped with energy-dispersive spectroscopy (EDS) were used to study the microstructure and intergranular corrosion morphology, and the precipitates were analyzed using X-ray diffraction (XRD) and transmission electron microscopy (TEM). The results showed that the mechanical properties of 2A12 aluminum alloy were improved by both non-isothermal aging techniques due to the formation of an S' phase and a point S″ phase in the alloy matrix. Linear non-isothermal aging resulted in better mechanical properties than composite non-isothermal aging. However, the corrosion resistance of the 2A12 aluminum alloy was reduced after non-isothermal aging due to the transformation of matrix precipitates and grain boundary precipitates. The corrosion resistance of the samples followed the order: annealed state > linear non-isothermal aging > composite non-isothermal aging.

| S-EPMC10254026 | biostudies-literature

Transition from poor ductility to room-temperature superplasticity in a nanostructured aluminum alloy.

Project description:Recent developments of nanostructured materials with grain sizes in the nanometer to submicrometer range have provided ground for numerous functional properties and new applications. However, in terms of mechanical properties, bulk nanostructured materials typically show poor ductility despite their high strength, which limits their use for structural applications. The present article shows that the poor ductility of nanostructured alloys can be changed to room-temperature superplastisity by a transition in the deformation mechanism from dislocation activity to grain-boundary sliding. We report the first observation of room-temperature superplasticity (over 400% tensile elongations) in a nanostructured Al alloy by enhanced grain-boundary sliding. The room-temperature grain-boundary sliding and superplasticity was realized by engineering the Zn segregation along the Al/Al boundaries through severe plastic deformation. This work introduces a new boundary-based strategy to improve the mechanical properties of nanostructured materials for structural applications, where high deformability is a requirement.

| S-EPMC5928095 | biostudies-literature

The Dependence of Isothermal ω Precipitation on the Quenching Rate in a Metastable β-Ti Alloy.

Project description:The precipitation behavior of the α strengthening phase in metastable β-Ti alloys is highly dependent on heat treatment parameters such as quenching rate, heating rate and ageing temperature. In this paper we have investigated the influence of quenching rate on the formation of isothermal ω precipitates that have been regarded as potent nucleant sites for α precipitation. The results show that the β-solutionized alloy contains a β matrix with a layer structured morphology. Regular atomic movement of the (002)β plane along the <002> direction was observed in the alloy. The increase in quenching rate refines the thickness of layers, subsequently influencing the nucleation and growth of isothermal ω precipitates after ageing treatment. The high quenching rate promotes the occurrence of ω precipitation, broadens the stage of ω precipitation and increases the number density of ω precipitates. Since the isothermal ω phase provides a heterogeneous nucleation site for α precipitates, it is inferred that the quenching rate may indirectly influence the mechanical properties of metastable β-Ti alloy.

| S-EPMC4598871 | biostudies-other

Non-Isothermal Oxidation Behavior and Mechanism of a High Temperature Near-? Titanium Alloy.

Project description:Non-isothermal oxidation is one of the important issues related to the safe application of high-temperature titanium alloys, so this study focuses on the non-isothermal oxidation behavior and mechanism of near-? titanium alloys. The thermogravimetry-differential scanning calorimetry (TGA/DSC) method was used to study the non-isothermal oxidation behavior of TA29 titanium alloy heated from room temperature to 1450 °C at a heating rate of 40 °C/min under pure oxygen atmosphere. The results show that non-isothermal oxidation behavior can be divided into five stages, including no oxidation, slow oxidation, accelerated oxidation, severe oxidation and deceleration oxidation; for the three-layer TiO? scale, Zr, Nb, Ta are enriched in the intermediate layer, while Al is rich in the inner layer and Sn is segregated at the oxide-substrate interface, which is related to their diffusion rates in the subsurface ? case. The oxidation mechanism for each stage is: oxygen barrier effect of a thin compact oxide film; oxygen dissolution; lattice transformation accelerating the dissolution and diffusion of oxygen; oxide formation; oxygen barrier effect of recrystallization and sintering microstructure in outer oxide scale. The alloying elements with high valence state and high diffusion rate in ?-Ti are favorable to slow down the oxidation rate at the stage governed by oxide formation.

| S-EPMC6267292 | biostudies-other

Aluminum-copper alloy anode materials for high-energy aqueous aluminum batteries.

Project description:Aqueous aluminum batteries are promising post-lithium battery technologies for large-scale energy storage applications because of the raw materials abundance, low costs, safety and high theoretical capacity. However, their development is hindered by the unsatisfactory electrochemical behaviour of the Al metal electrode due to the presence of an oxide layer and hydrogen side reaction. To circumvent these issues, we report aluminum-copper alloy lamellar heterostructures as anode active materials. These alloys improve the Al-ion electrochemical reversibility (e.g., achieving dendrite-free Al deposition during stripping/plating cycles) by using periodic galvanic couplings of alternating anodic α-aluminum and cathodic intermetallic Al2Cu nanometric lamellas. In symmetric cell configuration with a low oxygen concentration (i.e., 0.13 mg L-1) aqueous electrolyte solution, the lamella-nanostructured eutectic Al82Cu18 alloy electrode allows Al stripping/plating for 2000 h with an overpotential lower than ±53 mV. When the Al82Cu18 anode is tested in combination with an AlxMnO2 cathode material, the aqueous full cell delivers specific energy of ~670 Wh kg-1 at 100 mA g-1 and an initial discharge capacity of ~400 mAh g-1 at 500 mA g-1 with a capacity retention of 83% after 400 cycles.

| S-EPMC8803968 | biostudies-literature

Precipitation strengthening in an ultralight magnesium alloy.

Project description:Body-centred cubic magnesium-lithium-aluminium-base alloys are the lightest of all the structural alloys, with recently developed alloy compositions showing a unique multi-dimensional property profile. By hitherto unrecognised mechanisms, such alloys also exhibit exceptional immediate strengthening after solution treatment and water quenching, but strength eventually decreases during prolonged low temperature ageing. We show that such phenomena are due to the precipitation of semi-coherent D03-Mg3Al nanoparticles during rapid cooling followed by gradual coarsening and subsequent loss of coherency. Physical explanation of these phenomena allowed the creation of an exceptionally low-density alloy that is also structurally stable by controlling the lattice mismatch and volume fraction of the Mg3Al nanoparticles. The outcome is one of highest specific-strength engineering alloys ever developed.

| S-EPMC6397269 | biostudies-literature

Influence of Retrogression Time on the Fatigue Crack Growth Behavior of a Modified AA7475 Aluminum Alloy.

Project description:This paper investigates the effect of retrogression time on the fatigue crack growth of a modified AA7475 aluminum alloy. Tests including tensile strength, fracture toughness, and fatigue limits were performed to understand the changes in properties with different retrogression procedures at 180 °C. The microstructure was characterized using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The findings indicated that as the retrogression time increased, the yield strength decreased from 508 MPa to 461 MPa, whereas the fracture toughness increased from 48 MPa√m to 63.5 MPa√m. The highest fracture toughness of 63.5 MPa√m was seen after 5 h of retrogression. The measured diameter of η' precipitates increased from 6.13 nm at the retrogression 1 h condition to 6.50 nm at the retrogression 5 h condition. Prolonged retrogression also increased the chance of crack initiation, with slower crack growth rate in the long transverse direction compared to the longitudinal direction. An empirical relationship was established between fracture toughness and the volume fraction of age-hardening precipitates, with increasing number density of precipitates seen with increasing retrogression time.

| S-EPMC10095606 | biostudies-literature

Aluminum-Lithium Alloy Fillers Enhancing the Room Temperature Performances of Polymer Electrolytes for All-Solid-State Lithium Batteries.

Project description:Poly(ethylene oxide) (PEO) electrolytes usually suffer from low room temperature (RT) ionic conductivity and a narrow voltage window, which limits the improvement of energy density and practical applications in all-solid-state batteries. Composite polymer electrolytes (CPEs) are regarded as the common method to reduce the crystallinity of polymers and increase the lithium ion conductivity. Compared with active or inert ceramic material fillers in previous studies, aluminum-lithium alloy fillers are used to prepare composite electrolytes in this study, showing excellent performance at room temperature. The conductivity of the PEO-based electrolytes increases by a factor of 3.62-3.62× 10-4 S cm-1 at RT with 5 wt % Al-Li alloy. The transference number of Li+ is increased to 0.524. The characteristics of the Al-Li alloy and higher conductivity enable the composite electrolyte to stabilize the interface with the electrodes, reducing the polarization of solid-state batteries. The all-solid-state Li/PEO-5%/LiFePO4 cells show the highest initial discharge capacity of 153 mAh g-1 and the highest stable discharge capacity of 147 mAh g-1 with the initial Coulombic efficiency of more than 100%. It also exhibits the best rate capacity and cycle performance (90% capacity retention rate after 100 cycles).

| S-EPMC11339980 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data