Sintering Behaviour of Waste Olivine and Olivine/Alumina Blends.
Ontology highlight
ABSTRACT:
SUBMITTER: Furlani E
PROVIDER: S-EPMC5455912 | biostudies-other | 2014 Jun
REPOSITORIES: biostudies-other
Similar Datasets
Project description:The sintering of alumina (Al2O3) traditionally occurs at high temperatures (up to ca. 1700 °C) and in significantly long times (up to several hours), which are required for the consolidation of the material by diffusion processes. Here we investigate the photonic sintering of alumina particles using millisecond flash lamp irradiation with extreme heating rates up to 108 K/min. The limitation of the low visible light absorption of alumina is resolved by adding colored α-Fe2O3 nanoparticles, which initiated the grain growth during sintering. After the millisecond-long light pulses from a xenon flash lamp, a bimodal mixture of α-Al2O3 precursor particles was sintered and iron segregation at the grain boundaries was observed. The proposed photonic sintering approach based on doping with colored centers may be extended to other refractory ceramics with low absorption in the visible light range once appropriate high-absorbing dopants are identified.
| S-EPMC7878514 | biostudies-literature
Project description:Constructing continuous filler networks in a polymer
| S-EPMC9835650 | biostudies-literature
Project description:PurposeThe performance of carrier-based dry powder inhaler (DPI) formulations can be critically impacted by interfacial interactions driven by tribo-electrification. Therefore, the aim of the present work was to understand how distinct API particle characteristics affect the charging behaviour of blends intended for DPI delivery.MethodsSalbutamol sulphate (SBS) particles engineered via spray-drying and jet milling were used as model APIs. D-mannitol was selected as a model carrier. The materials were characterized concerning their different particle properties and their charge was analysed alone and in blends before and after flow over a stainless-steel pipe.ResultsThe spray-dried SBS (amorphous and spherical) charged positively and to a higher extent than jet milled SBS (crystalline and acicular) that charged negatively and to a lower extent. D-mannitol charged positively and to a higher extent than the APIs. All drug-excipient blends charged negatively and differences were found between the spray-dried and jet milled SBS blends at 2% and 5% drug loads.ConclusionsIt was demonstrated how distinct solid-states, particle shape, size and morphology as well as different water contents of the different materials can affect tribo-charging. For their binary blends, the amount and nature of fines seem to govern inter-particle contacts critically impacting charge evolution.
| S-EPMC6456482 | biostudies-literature
Project description:Ceramics and glass ceramics based on industrial waste have been widely recognized as competitive products for building applications; however, there is a great potential for such materials with novel functionalities. In this paper, we discuss the development of magnetic sintered glass ceramics based on two iron-rich slags, coming from non-ferrous metallurgy and recycled borosilicate glass. The substantial viscous flow of the glass led to dense products for rapid treatments at relatively low temperatures (900-1000 °C), whereas glass/slag interactions resulted in the formation of magnetite crystals, providing ferrimagnetism. Such behavior could be exploited for applying the obtained glass ceramics as induction heating plates, according to preliminary tests (showing the rapid heating of selected samples, even above 200 °C). The chemical durability and safety of the obtained glass ceramics were assessed by both leaching tests and cytotoxicity tests.
| S-EPMC5456182 | biostudies-other
Project description:Two novel symmetrical bis-azobenzene red dyes ending with electron-withdrawing or donor groups were synthesized. Both chromophores display good solubility, excellent chemical, and thermal stability. The two dyes are fluorescent in solution and in the solid-state. The spectroscopic properties of the neat crystalline solids were compared with those of doped blends of different amorphous matrixes. Blends of non-conductive and of emissive and conductive host polymers were formed to evaluate the potential of the azo dyes as pigments and as fluorophores. Both in absorbance and emission, the doped thin layers have CIE coordinates in the spectral region from yellow to red. The fluorescence quantum yield measured for the brightest emissive blend reaches 57%, a remarkable performance for a steadily fluorescent azo dye. A DFT approach was employed to examine the frontier orbitals of the two dyes.
| S-EPMC7144390 | biostudies-literature
Project description:In Europe, most of the discarded and un-wearable textiles are incinerated or landfilled. In this study, we present an enzyme-based strategy for the recovery of valuable building blocks from mixed textile waste and blends as a circular economy concept. Therefore, model and real textile waste were sequentially incubated with (1) protease for the extraction of amino acids from wool components (95% efficiency) and (2) cellulases for the recovery of glucose from cotton and rayon constituents (85% efficiency). The purity of the remaining poly(ethylene terephthalate) (PET) unaltered by the enzymatic treatments was assessed via Fourier-transformed infrared spectroscopy. Amino acids recovered from wool were characterized via elementary and molecular size analysis, while the glucose resulting from the cotton hydrolysis was successfully converted into ethanol by fermentation with Saccharomyces cerevisiae. This work demonstrated that the step-wise application of enzymes can be used for the recovery of pure building blocks (glucose) and their further reuse in fermentative processes.
| S-EPMC6403871 | biostudies-literature
Project description:Polyolefin (PO) polymers constitute the majority of consumer plastic commodities. The reliance on such materials make it near imposable to avoid touching one in any given day. Therefore, the accumulation of plastic solid waste (PSW) in developed and developing societies alike requires immediate attention to manage and valorize this type of waste. In this work, PSW originating from real life sources and virgin linear low-density polyethylene (LLDPE) films were compounded in a mechanical recycling effort. The recycled blends constituted up to 100% (by weight) of the waste material. Accelerated weathering (aging) was conducted on the blends, reaching threshold limit of exposure to study the major changes occurring on the recycled blends. Thermogravimetry and differential scanning calorimetry (DSC) were used to determine their characteristics and applicability for future recycling using thermo-chemical treatment (TCT) methods. Analytical solution methods following the international committee of thermal analysis and calorimetry (ICTAC) were followed in conducting the measurements and kinetic calculations alike. A novel analytical mathematical solution model is also introduced to determine both the pre-exponential factor (Ao) and apparent activation energy (Ea) of the degradation reaction. The model proved to be a more accurate analysis tool, and the work in whole enabled the determination of future plans for using such waste components as a feedstock to thermal units.
| S-EPMC6388198 | biostudies-literature
Project description:A deposit of raw kaolin, located in West Andalusia (Spain), was studied in this work using a representative sample. The methods of characterization were X-ray diffraction (XRD), X-ray fluorescence (XRF), particle size analysis by sieving and sedimentation, and thermal analysis. The ceramic properties were determined. A sample of commercial kaolin from Burela (Lugo, Spain), with applications in the ceramic industry, was used in some determinations for comparison purposes. The kaolin deposit has been produced by alteration of feldspar-rich rocks. This raw kaolin was applied as an additive in local manufactures of ceramics and refractories. However, there is not previous studies concerning its characteristics and firing properties. Thus, the meaning of this investigation was to conduct a scientific study on this subject and to evaluate the possibilities of application. The raw kaolin was washed for the beneficiation of the rock using water to increase the kaolinite content of the resultant material. The results indicated that the kaolinite content of the raw material was 20 wt % as determined by XRD, showing ~23 wt % of particles lower than 63 µm. The kaolinite content of the fraction lower than 63 µm was 50 wt %. Thus, an improvement of the kaolinite content of this raw kaolin was produced by wet separation. However, the kaolin was considered as a waste kaolin, with microcline, muscovite and quartz identified by XRD. Thermal analyses by Thermo-Dilatometry (TD), Differential Thermal Analysis (DTA) and Thermo-Gravimetry (TG) allowed observe kaolinite thermal decomposition, quartz phase transition and sintering effects. Pressed samples of this raw kaolin, the fraction lower than 63 µm obtained by water washing and the raw kaolin ground using a hammer mill were fired at several temperatures in the range 1000-1500 °C for 2 h. The ceramic properties of all these samples were determined and compared. The results showed the progressive linear firing shrinkage by sintering in these samples, with a maximum value of ~9% in the fraction lower than 63 µm. In general, water absorption capacity of the fired samples showed a decrease from ~18-20% at 1050 °C up to almost zero after firing at 1300 °C, followed by an increase of the experimental values. The open porosity was almost zero after firing at 1350 °C for 2 h and the bulk density reached a maximum value of 2.40 g/cm3 as observed in the ground raw kaolin sample. The XRD examination of fired samples indicated that they are composed by mullite, from kaolinite thermal decomposition, and quartz, present in the raw sample, as main crystalline phases besides a vitreous phase. Fully-densified or vitrified materials were obtained by firing at 1300-1350 °C for 2 h. In a second step of this research, it was examined the promising application of the previous study to increase the amount of mullite by incorporation of alumina (α-alumina) to this kaolin sample. Firing of mixtures, prepared using this kaolin and α-alumina under wet processing conditions, produced the increase of mullite in relative proportion by reaction sintering at temperatures higher than 1500 °C for 2 h. Consequently, a mullite refractory can be prepared using this kaolin. This processing of high-alumina refractories is favoured by a previous size separation, which increases the kaolinite content, or better a grinding treatment of the raw kaolin.
| S-EPMC8780162 | biostudies-literature
Project description:Polyurethane (PU) is a very popular polymer that is used in a variety of applications due to its good mechanical, thermal, and chemical properties. However, PU recycling has received significant attention due to environmental issues. In this study, we developed a recycling method for waste PU that utilizes the radiation grafting technique. Grafting of waste PU was carried out using a radiation technique with polyethylene-graft-maleic anhydride (PE-g-MA). The PE-g-MA-grafted PU/high density polyethylene (HDPE) composite was prepared by melt-blending at various concentrations (0-10 phr) of PE-g-MA-grafted PU. The composites were characterized using fourier transform infrared spectroscopy (FT-IR), and their surface morphology and thermal/mechanical properties are reported. For 1 phr PU, the PU could be easily introduced to the HDPE during the melt processing in the blender after the radiation-induced grafting of PU with PE-g-MA. PE-g-MA was easily reacted with PU according to the increasing radiation dose and was located at the interface between the PU and the HDPE during the melt processing in the blender, which improved the interfacial interactions and the mechanical properties of the resultant composites. However, the elongation at break for a PU content >2 phr was drastically decreased.
| S-EPMC5507029 | biostudies-other
Project description:In the current study, the physicochemical, engine performance, and exhaust emission of different ternary fuel blends containing waste fish oil (WFO) biodiesel, bioethanol, and petro-diesel have been investigated. WFO Biodiesel was prepared from waste fish oil via transesterification method. Different physiochemical properties including the kinematic viscosity, density, flash point, pour point, cloud point, and heat value have been measured for different fuel blends and compared with the neat petro-diesel. The performance and exhaust emission of engine have been also studied using different fuel blends using a single-cylinder diesel engine in full load condition at 1800 rpm. It was found that the engine torque, engine power, and thermal efficiency of the ternary fuel blends was reduced by 2.45%, 9.25%, 2.35% averagely in comparison with the neat petro-diesel, respectively. The average break specific fuel consumption was also increased by 10.44% compared to the neat petro-diesel. The emission of carbon monoxide (CO), carbon dioxide (CO2), unburned hydrocarbons (UHC), and nitrogen oxides (NOx) was also measured. It was also found that the utilization of ternary fuel blends results in a considerable reduction in CO and UHC emission by 50.55% and 43.87% on average compared to the neat petro-diesel, respectively. The emission of NOx was also increased by 28.25% on average compared to the neat petro-diesel. It was also found that the NOx emission can be adjusted by tuning the WFO biodiesel and bioethanol contents of the ternary fuel blends.
| S-EPMC10462698 | biostudies-literature