Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Structure and Compressive Properties of Invar-Cenosphere Syntactic Foams.

ABSTRACT: The present study investigates the mechanical performance of syntactic foams produced by means of the metal powder injection molding process having an Invar (FeNi36) matrix and including cenospheres as hollow particles at weight fractions (wt.%) of 5 and 10, respectively, corresponding to approximately 41.6 and 60.0 vol.% in relation to the metal content and at 0.6 g/cm³ hollow particle density. The synthesis process results in survival of cenospheres and provides low density syntactic foams. The microstructure of the materials is investigated as well as the mechanical performance under quasi-static and high strain rate compressive loads. The compressive stress-strain curves of syntactic foams reveal a continuous strain hardening behavior in the plastic region, followed by a densification region. The results reveal a strain rate sensitivity in cenosphere-based Invar matrix syntactic foams. Differences in properties between cenosphere- and glass microsphere-based materials are discussed in relation to the findings of microstructural investigations. Cenospheres present a viable choice as filler material in iron-based syntactic foams due to their higher thermal stability compared to glass microspheres.

SUBMITTER: Luong D

PROVIDER: S-EPMC5456466 | biostudies-other | 2016 Feb

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

Synthesis and Quasi-Static Compressive Properties of Mg-AZ91D-Al₂O₃ Syntactic Foams.

Project description:Magnesium alloys have considerably lower density than the aluminum alloy matrices that are typically used in syntactic foams, allowing for greater specific energy absorption. Despite the potential advantages, few studies have reported the properties of magnesium alloy matrix syntactic foams. In this work, Al₂O₃ hollow particles of three different size ranges, 0.106-0.212 mm, 0.212-0.425 mm, and 0.425-0.500 mm were encapsulated in Mg-AZ91D by a sub-atmospheric pressure infiltration technique. It is shown that the peak strength, plateau strength and toughness of the foam increases with increasing hollow sphere wall thickness to diameter (t/D) ratio. Since t/D was found to increase with decreasing hollow sphere diameter, the foams produced with smaller spheres showed improved performance-specifically, higher energy absorption per unit weight. These foams show better performance than other metallic foams on a specific property basis.

| S-EPMC5512899 | biostudies-other

Effect of the Aromatic Amine Curing Agent Structure on Properties of Epoxy Resin-Based Syntactic Foams.

Project description:Epoxy resin is one of the commonly used matrixes of syntactic foams as a buoyancy material, the curing agents of which affect some of the properties for syntactic foams. Therefore, the curing reactions of N,N,N',N'-tetraepoxypropyl-4,4'-diaminodiphenylmethane (AG-80) epoxy resin between 4,4-diaminodiphenyl methane (DDM) and the mixture of m-xylylenediamine and DDM (DDM-m-XDA) systems are studied. The DDM mixed with m-XDA enhances curing reactions with the AG-80 epoxy resin, and the mechanisms of the two curing systems are different through nonisothermal kinetics. Compared with a single curing system, there are some wrinkles on the surface of the AG-80/DDM-m-XDA matrix because of the disordered network. Composited with hollow glass microspheres (HGMs), the more flexible m-XDA structure enhances the interfacial adhesion between the matrix and HGM for syntactic foams. However, the wrinkles in the matrix increase the broken degree of HGMs; especially at HGM contents higher than 55%, the flaw increases the density and water absorption of syntactic foams; meanwhile, it decreases the compressive strength. Therefore, the properties of syntactic foams can be improved by mixing different molecular structure curing agents and the mixture liquid curing agent simplifies the preparation process to some extent.

| S-EPMC7495733 | biostudies-literature

Compressive Behavior and Microstructural Characteristics of Iron Hollow Sphere Filled Aluminum Matrix Syntactic Foams.

Project description:Iron hollow sphere filled aluminum matrix syntactic foams (AMSFs) were produced by low pressure, inert gas assisted infiltration. The microstructure of the produced AMSFs was investigated by light and electron microscopy, extended by energy dispersive X-ray spectroscopy and electron back-scattered diffraction. The investigations revealed almost perfect infiltration and a slight gradient in the grain size of the matrix. A very thin interface layer that ensures good bonding between the hollow spheres and the matrix was also observed. Compression tests were performed on cylindrical specimens to explore the characteristic mechanical properties of the AMSFs. Compared to other (conventional) metallic foams, the investigated AMSFs proved to have outstanding mechanical properties (yield strength, plateau strength, etc.) and energy absorbing capability.

| S-EPMC5458885 | biostudies-other

Data characterizing compressive properties of Al/Al2O3 syntactic foam core metal matrix sandwich.

Project description:Microstructural observations and compressive property datasets of metal matrix syntactic foam core sandwich composite at quasi-static and high strain rate (HSR) conditions (525-845 s(-1)) are provided. The data supplied in this article includes sample preparation procedure prior to scanning electron and optical microscopy as well as the micrographs. The data used to construct the stress-strain curves and the derived compressive properties of all specimens in both quasi-static and HSR regions are included. Videos of quasi-static compressive failure and that obtained by a high speed image acquisition system during deformation and failure of HSR specimen are also included.

| S-EPMC4624990 | biostudies-literature

Syntactic Iron Foams' Properties Tailored by Means of Case Hardening via Carburizing or Carbonitriding.

Project description:Metal foam inserts are known for their high potential for weight and vibration reduction in composite gear wheels. However, most metal foams do not meet the strength requirements mandatory for the transfer of sufficiently high levels of torque by the gears. Syntactic iron and steel foams offer higher strength levels than conventional two-phase metal foams, thus making them optimum candidates for such inserts. The present study investigates to what extent surface hardening treatments commonly applied to gear wheels can improve the mechanical properties of iron-based syntactic foams. Experiments performed thus focus on case hardening treatments based on carburizing and carbonitriding, with subsequent quenching and tempering to achieve surface hardening effects. Production of samples relied on the powder metallurgical metal injection molding (MIM) process. Syntactic iron foams containing 10 wt.% of S60HS hollow glass microspheres were compared to reference materials without such filler. Following heat treatments, the samples' microstructure was evaluated metallographically; mechanical properties were determined via hardness measurements on reference samples and 4-point bending tests, on both reference and syntactic foam materials. The data obtained show that case hardening can indeed improve the mechanical performance of syntactic iron foams by inducing the formation of a hardened surface layer. Moreover, the investigation indicates that the respective thermo-chemical treatments can be applied to composite gear wheels in exactly the same way as to monolithic ones. In the surface region modified by the treatment, martensitic microstructures were observed, and as consequence, the bending limits of syntactic foam samples were increased by a factor of three.

| S-EPMC8398341 | biostudies-literature

Water Impact of Syntactic Foams.

Project description:Syntactic foams are particulate composite materials that are extensively integrated in naval and aerospace structures as core materials for sandwich panels. While several studies have demonstrated the potential of syntactic foams as energy absorbing materials in impact tests, our understanding of their response to water impact remains elusive. In this work, we attempt a first characterization of the behavior of a vinyl ester/glass syntactic subject to slamming. High-speed imaging is leveraged to elucidate the physics of water impact of syntactic foam wedges in a free-fall drop tower. From the images, we simultaneously measure the deformation of the wedge and the hydrodynamic loading, thereby clarifying the central role of fluid-structure interaction during water impact. We study two different impact heights and microballoon density to assess the role of impact energy and syntactic foam composition on the slamming response. Our results demonstrate that both these factors have a critical role on the slamming response of syntactic foams. Reducing the density of microballoons might help to reduce the severity of the hydrodynamic loading experienced by the wedge, but this comes at the expense of a larger deformation. Such a larger deformation could ultimately lead to failure for large drop heights. These experimental results offer compelling evidence for the role of hydroelastic coupling in the slamming response of syntactic foams.

| S-EPMC5503347 | biostudies-other

Effect of Fly-Ash Cenospheres on Properties of Clay-Ceramic Syntactic Foams.

Project description:A low-density clay ceramic syntactic foam (CSF) composite material was successfully synthesized from illitic clay added by fly ash cenospheres (CS) using the semi-dry formation method. The content of CS varied in the range of 10, 30, 50 and 60 vol %. Furthermore, reference samples without cenospheres were produced for property comparison. The materials comprising different amount of the additives were fired at temperatures of 600, 950, 1000, 1050, 1100, 1150 and 1200 °C. Firing times were kept constant at 30 min. Processing characteristics of the materials were evaluated in terms of density achieved and shrinkage observed as functions of both the CS content and the sintering temperature. The compressive strength and water uptake were determined as application-oriented properties. Except for the reference and the low CS level samples, the materials show an increase in strength with the increase in firing temperature, and a decrease of mechanical reliability with a decrease in density, which is typical for porous materials. Exceptions are the samples with no or low (10 vol %) content of cenospheres. In this case, the maximum strength is obtained at an intermediate sintering temperature of 1100 °C. At a low density (1.10 and 1.25 g/cm³), the highest levels of strength are obtained after sintering at 1200 °C. For nominal porosity levels of 50 and 60 vol %, 41 and 26 MPa peak stresses, respectively, are recorded under compressive load.

| S-EPMC5551871 | biostudies-other

Compressive Properties of Open-Cell Al Hybrid Foams at Different Temperatures.

Project description:Hybrid Ni/Al foams were fabricated by depositing electroless Ni-P (EN) coatings on open-cell Al foam substrate to obtain enhanced mechanical properties. The microstructure, chemical components and phases of the hybrid foams were observed and analyzed by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD), respectively. The mechanical properties of the foams were studied by compressive tests at different temperatures. The experiment results show that the coating is mainly composed of Ni and P elements. There was neither defect at the interface nor crack in the coatings, indicating that the EN coatings had fine adhesion to the Al substrate. The compressive strengths and energy absorption capacities of the as-received foam and hybrid foams decrease with the increasing testing temperatures, but the hybrid foams exhibit a lower decrement rate than the as-received foam. This might be attributed to the different failure mechanisms at different testing temperatures, which is conformed by fractography observation.

| S-EPMC5459119 | biostudies-other

Influences of Increased Pressure Foaming on the Cellular Structure and Compressive Properties of In Situ Al-4.5%Cu-xTiB2 Composite Foams with Different Particle Fraction.

Project description:Metallic foams have drawn increasing attention in applications ranging from lightweight structures to energy absorption devices. Mechanical properties of metallic foams depend on both their microstructure and cellular structure. In situ Al-4.5%Cu-xTiB2 composites were used as start materials for fabrication of closed-cell foams through liquid route under atmosphere pressure and increased pressure, aiming at simultaneously strengthening the cell wall material and optimizing the cellular structure. Macro-structural features of the foams were determined by micro X-ray computed tomography (µCT); results exhibit that increasing weight ratio of in situ TiB2 particles leads to coarsened cell structure for foams made under atmosphere pressure, due to the increase in critical thickness of cell wall rupture. Significant reduction of cell size and increase in cell circularity were observed for foams fabricated under increased pressure. Quasi static compression test results indicate that yield strength of foam samples increases with increasing particle fraction and refinement of cell structure. Microstructure observation shows that the continuous network at interdendritic regions consists of in situ TiB2 particles and intermetallic compounds are responsible for the reduced ductility of cell wall materials and the reduction in energy absorption efficiency of foams with high particle fraction. The influences of cell structure on the normalized strength and specific energy absorption were also discussed, and it was found that the improvement of yield strength and energy absorption of composite foams attributes to both the reinforcement of in situ TiB2 particles and the refinement of cellular structure.

| S-EPMC8157061 | biostudies-literature

Compressive Behavior of Al-TiB2 Composite Foams Fabricated under Increased Pressure.

Project description:The application of increased pressure was used as a strategy to investigate the effect of different cell structures on the mechanical properties of Al-TiB2 composite foams. In situ Al-xTiB2 (x = 5, 10 wt.%) composites were foamed under three different pressures (0.1 MPa, 0.24 MPa, 0.4 MPa) through the liquid melt route. The macro-structure of the composite foams was analyzed in terms of cell size distribution measured by X-ray microcomputed tomography (micro-CT). It was found that the mean cell size decreases, and the cell size distribution range narrows with increasing pressure. Uniaxial compression tests revealed that the stress fluctuation (Rsd) of 10TiB2 foams is larger than that of 5TiB2 foams under the same pressure. Moreover, cell size refinement causes the simultaneous deformation of multi-layer cells, which leads to an enhancement in the energy absorption efficiency and specific energy absorption. The comparison of experimental data with theoretical predictions (G&A model) is discussed.

| S-EPMC8434092 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data