Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Fabrication of Lead-Free Bi0.5Na0.5TiO₃ Thin Films by Aqueous Chemical Solution Deposition.

ABSTRACT: Piezoelectric ceramics are widely used in actuator applications, and currently the vast majority of these devices are based on Pb ( Zr , Ti ) O 3 , which constitutes environmental and health hazards due to the toxicity of lead. One of the most promising lead-free material systems for actuators is based on Bi 0 . 5 Na 0 . 5 TiO 3 (BNT), and here we report on successful fabrication of BNT thin films by aqueous chemical solution deposition. The precursor solution used in the synthesis is based on bismuth citrate stabilized by ethanolamine, NaOH , and a Ti-citrate prepared from titanium tetraisopropoxide and citric acid. BNT thin films were deposited on SrTiO 3 and platinized silicon substrates by spin-coating, and the films were pyrolized and annealed by rapid thermal processing. The BNT perovskite phase formed after calcination at 500 °C in air. The deposited thin films were single phase according to X-ray diffraction, and the microstructures of the films shown by electron microscopy were homogeneous and dense. Decomposition of the gel was thoroughly investigated, and the conditions resulting in phase pure materials were identified. This new aqueous deposition route is low cost, robust, and suitable for development of BNT based thin film for actuator applications.

SUBMITTER: Christensen M

PROVIDER: S-EPMC5459111 | biostudies-other | 2017 Feb

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

Epitaxial K0.5Na0.5NbO3 thin films by aqueous chemical solution deposition.

Project description:We report on an environmentally friendly and versatile aqueous chemical solution deposition route to epitaxial K0.5Na0.5NbO3 (KNN) thin films. The route is based on the spin coating of an aqueous solution of soluble precursors on SrTiO3 single crystal substrates followed by pyrolysis at 400°C and annealing at 800°C using rapid thermal processing. Strongly textured films with homogeneous thickness were obtained on three different crystallographic orientations of SrTiO3. Epitaxial films were obtained on (111) SrTiO3 substrates, while films consisting of an epitaxial layer close to the substrate followed by an oriented polycrystalline layer were obtained on (100) and (110) SrTiO3 substrates. A K2Nb4O11 secondary phase was observed on the surface of the thin films due to the evaporation of alkali species, while the use of an NaCl/KCl flux reduced the amount of the secondary phase. Ferroelectric behaviour of the films was investigated by PFM, and almost no dependence on the film crystallographic orientation was observed. The permittivity and loss tangent of the films with the NaCl/KCl flux were 870 and 0.04 (100-orientation) and 2250 and 0.025 (110-orientation), respectively, at 1 kHz.

| S-EPMC6366202 | biostudies-literature

Photocurrent Enhancement by Copper Incorporation in Chemical-Solution-Synthesized Inorganic Lead Perovskite Thin Films.

Project description:Perovskite thin films are at the forefront of highly promising photovoltaic technologies due to their remarkable optoelectronic properties. Herein, we explore a low-cost, reproducible, and industry-scalable methodology to synthesize an all-inorganic CsPbI1.5Br1.5 perovskite thin film with additional incorporation of copper and chloride ions into the lattice structure. The synthesis process involves chemical bath deposition of PbS, followed by a gas-solid iodination reaction to yield PbI2. Subsequently, dip-coating incorporates Cs+, Cu2+, Br-, and Cl- ions into PbI2, and annealing at 270 °C produces perovskite thin films. The results show a large coverage area and a uniform thickness of each perovskite thin film. Comprehensive characterization, including X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, and photoluminescence, provides the structural, chemical, and optical properties of the synthesized thin films. To evaluate the practical implications of our methodology, we fabricated photodetectors employing CsPbI1.5Br1.5 and (Cs0.95:Cu0.01)PbI1.5Br1.3Cl0.1 perovskite films. A comparative analysis unequivocally demonstrates a significant increase in photodetector performance when utilizing (Cs0.95:Cu0.01)PbI1.5Br1.3Cl0.1 perovskite films. While our findings quantitatively assess the tangible enhancement in photocurrent, we acknowledge the potential for improvement in device fabrication to enhance the overall performance. This study not only affirms the successful low-cost synthesis of perovskite thin films but also emphasizes the pivotal role of Cu2+ and Cl- ions in enhancing the performance of perovskite-based optoelectronic devices.

| S-EPMC10993397 | biostudies-literature

Thin films of formamidinium lead iodide (FAPI) deposited using aerosol assisted chemical vapour deposition (AACVD).

Project description:Formamidinium lead iodide (CH(NH2)2PbI3, FAPI) thin films have been deposited on glass substrates at 150 °C using ambient pressure aerosol assisted chemical vapour deposition (AACVD). The films have been analysed by a range of techniques including powder X-ray diffraction (pXRD), scanning electron microscopy (SEM), energy dispersive X-ray (EDX) spectroscopy, and UV-Vis-NIR absorption spectroscopy. Sharp reflections in the pXRD pattern can be indexed to the α-phase of FAPI which confirms the crystallinity of the as-deposited film and reveals a preferred growth orientation along the (002) plane with respect to the substrate. High magnification SEM images show that the thin film is comprised of a network of intimately connected FAPI crystallites which form a mesoporous architecture. EDX mapping of lead and iodine emission peaks show that the Pb and I within these films are spatially co-localised. Optical measurements show as-deposited FAPI films have absorption onsets in the near infra-red with a direct bandgap value of 1.46 eV, suitable for single junction solar cells. Four-point probe measurement of as deposited films show that the electrical conductivity (σ) of the FAPI thin film is 5.2 × 10-7 S/cm, which is similar to FAPI thin films deposited by spin coating technique.

| S-EPMC7747716 | biostudies-literature

Oxidative chemical vapor deposition of polyaniline thin films.

Project description:Polyaniline (PANI) is synthesized via oxidative chemical vapor deposition (oCVD) using aniline as monomer and antimony pentachloride as oxidant. Microscopy and spectroscopy indicate that oCVD processing conditions influence the PANI film chemistry, oxidation, and doping level. Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS) indicate that a substrate temperature of 90 °C is needed to minimize the formation of oligomers during polymerization. Lower substrate temperatures, such as 25 °C, lead to a film that mostly includes oligomers. Increasing the oxidant flowrate to nearly match the monomer flowrate favors the deposition of PANI in the emeraldine state, and varying the oxidant flowrate can directly influence the oxidation state of PANI. Changing the reactor pressure from 700 to 35 mTorr does not have a significant effect on the deposited film chemistry, indicating that the oCVD PANI process is not concentration dependent. This work shows that oCVD can be used for depositing PANI and for effectively controlling the chemical state of PANI.

| S-EPMC5480348 | biostudies-literature

Chemical Solution Deposition of Barium Titanate Thin Films with Ethylene Glycol as Solvent for Barium Acetate.

Project description:Chemical solution deposition (CSD) of BaTiO3 (BT) or BT-based thin films relies on using a carboxylic acid and alcohol as the solvents for alkaline-earth carboxylate and transition-metal alkoxide, respectively; however, the esterification reaction of the solvents may lead to in-situ water formation and precipitation. To avoid such an uncontrolled reaction, we developed a route in which ethylene glycol (EG) is used as the solvent for Ba-acetate. The EG-based BT coating solutions are stable for at least a few months. The thermal decomposition of the BT xerogel obtained by drying the EG-based solutions depends on the choice of the solvent for the Ti-alkoxide as well: in the case of EG and 2-methoxyethanol solvents carbon residues are removed at only about 1100 °C, while in the case of ethanol it is concluded at about 700 °C. About 100 nm thick BT films derived from the EG-ethanol solution deposited on platinized silicon reveal dense, crack-free columnar microstructure. They exhibit local ferro- and piezoelectric properties. The macroscopic polarization-electric field loops were obtained up to a quite high electric field of about 2.4 MV/cm. The EG-ethanol based CSD route is a viable alternative to the established acetic acid-alcohol route for BT and BT-based films.

| S-EPMC9230800 | biostudies-literature

One-Step Solution Deposition of Antimony Selenoiodide Films via Precursor Engineering for Lead-Free Solar Cell Applications.

Project description:Ternary chalcohalides are promising lead-free photovoltaic materials with excellent optoelectronic properties. We propose a simple one-step solution-phase precursor-engineering method for antimony selenoiodide (SbSeI) film fabrication. SbSeI films were fabricated by spin-coating the precursor solution, and heating. Various precursor solutions were synthesized by adjusting the molar ratio of two solutions based on SbCl3-selenourea and SbI3. The results suggest that both the molar ratio and the heating temperature play key roles in film phase and morphology. Nanostructured SbSeI films with a high crystallinity were obtained at a molar ratio of 1:1.5 and a temperature of 150 °C. The proposed method could be also used to fabricate (Bi,Sb)SeI.

| S-EPMC8703622 | biostudies-literature

Chemical Vapor Deposition of Highly Conjugated, Transparent Boron Carbon Nitride Thin Films.

Project description:Ternary materials made up only from the lightweight elements boron, carbon, and nitrogen are very attractive due to their tunable properties that can be obtained by changing the relative elemental composition. However, most of the times, the synthesis requires to use up to three different precursor and very high temperatures for the synthesis. Moreover, the low reciprocal solubility of boron nitride and graphene often leads to BN-C composite materials due to phase segregation. Herein, an innovative method is presented to prepare BCN thin films by chemical vapor deposition from a single source precursor, melamine diborate. The deposition occurs homogenously at relatively low temperatures generating very high degree of sp2 conjugation. The as-prepared thin films possess high transparency and refractive index values in the visible range that are of interest for reflective mirrors and lenses. Furthermore, they are wide-bandgap semiconductor with very positive valence band, making these materials very stable against oxidation of interest as protective coating and charge transport layer for solar cells. The simple chemical vapor deposition method that relies on commonly available and low-hazard precursor can open the way for application of BCN thin films in optics, optoelectronics, and beyond.

| S-EPMC8425861 | biostudies-literature

Tailoring of Multisource Deposition Conditions towards Required Chemical Composition of Thin Films.

Project description:The model to tailor the required chemical composition of thin films fabricated via multisource deposition, exploiting basic physicochemical constants of source materials, is developed. The model is experimentally verified for the two-source depositions of chalcogenide thin films from Ga-Sb-Te system (tie-lines GaSb-GaTe and GaSb-Te). The thin films are deposited by radiofrequency magnetron sputtering using GaSb, GaTe, and Te targets. Prepared thin films are characterized by means of energy dispersive X-ray analysis coupled with a scanning electron microscope to determine the chemical composition and by variable angle spectroscopic ellipsometry to establish film thickness. Good agreement between results of calculations and experimentally determined compositions of the co-deposited thin films is achieved for both the above-mentioned tie-lines. Moreover, in spite of all the applied simplifications, the proposed model is robust to be generally used for studies where the influence of thin film composition on their properties is investigated.

| S-EPMC9182166 | biostudies-literature

Growth Regimes of Poly(perfluorodecyl acrylate) Thin Films by Initiated Chemical Vapor Deposition.

Project description:Control over thin film growth (e.g., crystallographic orientation and morphology) is of high technological interest as it affects several physicochemical material properties, such as chemical affinity, mechanical stability, and surface morphology. The effect of process parameters on the molecular organization of perfluorinated polymers deposited via initiated chemical vapor deposition (iCVD) has been previously reported. We showed that the tendency of poly(1H,1H,2H,2H-perfluorodecyl acrylate) (pPFDA) to organize in an ordered lamellar structure is a function of the filament and substrate temperatures adopted during the iCVD process. In this contribution, a more thorough investigation of the effect of such parameters is presented, using synchrotron radiation grazing incidence and specular X-ray diffraction (GIXD and XRD) and atomic force microscopy (AFM). The parameters influencing the amorphization, mosaicity, and preferential orientation are addressed. Different growth regimes were witnessed, characterized by a different surface structuring and by the presence of particular crystallographic textures. The combination of morphological and crystallographic analyses allowed the identification of pPFDA growth possibilities between island or columnar growth.

| S-EPMC6096450 | biostudies-literature

Low-Cost One-Step Fabrication of Highly Conductive ZnO:Cl Transparent Thin Films with Tunable Photocatalytic Properties via Aerosol-Assisted Chemical Vapor Deposition.

Project description:Low-cost, high-efficiency, and high quality Cl-doped ZnO (ZnO:Cl) thin films that can simultaneously function as transparent conducting oxides (TCOs) and photocatalysts are described. The films have been fabricated by a facile and inexpensive solution-source aerosol-assisted chemical vapor deposition technique using NH4Cl as an effective, cheap, and abundant source of Cl. Successful ClO substitutional doping in the ZnO films was evident from powder X-ray diffraction, X-ray photoelectron spectroscopy, and time-of-flight secondary ion mass spectrometry results, while scanning electron microscopy reveals the impact of Cl doping on the ZnO thin film morphology. All ZnO:Cl films deposited were transparent and uncolored; optical transmittance in the visible region (400-700 nm) exceeded 80% for depositions using 5-20 mol % Cl. Optimal electrical properties were achieved when using 5 mol % Cl with a minimum measured resistivity of (2.72 ± 0.04) × 10-3 ?·cm, in which the charge carrier concentration and mobility were measured at (8.58 ± 0.16) × 1019 cm-3 and 26.7 ± 0.1 cm2 V-1 s-1 respectively, corresponding to a sheet resistance (R sh) of 41.9 ??-1 at a thickness of 650 nm. In addition to transparent conducting properties, photocatalytic behavior of stearic acid degradation in the ZnO:Cl films was also observed with an optimal Cl concentration of 7 mol % Cl, with the highest formal quantum efficiency (?) measured at (1.63 ± 0.03) × 10-4 molecule/photon, while retaining a visible transparency of 80% and resistivity ? = (9.23 ± 0.13) × 10-3 ?·cm. The dual functionality of ZnO:Cl as both a transparent conductor and an efficient photocatalyst is a unique combination of properties making this a particularly unusual material.

| S-EPMC7011732 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data