SiO₂-CaO-P₂O₅ Bioactive Glasses: A Promising Curcuminoids Delivery System.
Ontology highlight
ABSTRACT:
SUBMITTER: Nicolini V
PROVIDER: S-EPMC5502983 | biostudies-other | 2016 Apr
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Knowledge of the crystallization stability of bioactive glasses (BGs) is a key factor in developing porous scaffolds for hard tissue engineering. Thus, the crystallization behavior of three mesoporous bioactive glasses (MBGs) in the 70SiO2-(26-x)CaO-4P2O5-xCeO2 system (x stands for 0, 1 and 5 mol. %, namely MBG(0/1/5)Ce), prepared using the sol-gel method coupled with the evaporation-induced self-assembly method (EISA), was studied. A thermal analysis of the multiple-component crystallization exotherms from the DSC scans was performed using the Kissinger method. The main crystalline phases of Ca5(PO4)2.823(CO3)0.22O, CaSiO3 and CeO2 were confirmed to be generated by the devitrification of the MBG with 5% CeO2, MBG5Ce. Increasing the ceria content triggered a reduction in the first crystallization temperature while ceria segregation took place. The amount of segregated ceria of the annealed MBG5Ce decreased as the annealing temperature increased. The optimum processing temperature range to avoid the crystallization of the MBG(0/1/5)Ce powders was established.
| S-EPMC9222617 | biostudies-literature
Project description:Although forsterite (Mg₂SiO₄) possesses good biocompatibility and suitable mechanical properties, the insufficient bioactivity and degradability hinders its further application. In this study, a novel MgO-CaO-SiO₂ system was developed by adding wollastonite (CaSiO₃) into Mg₂SiO₄ to fabricate bone scaffolds via selective laser sintering (SLS). The apatite-forming ability and degradability of the scaffolds were enhanced because the degradation of CaSiO₃ could form silanol groups, which could offer nucleation sites for apatite. Meanwhile, the mechanical properties of the scaffolds grew with increasing CaSiO₃ to 20 wt %. It was explained that the liquid phase of CaSiO₃ promoted the densification during sintering due to its low melting point. With the further increase in CaSiO₃, the mechanical properties decreased due to the formation of the continuous filling phase. Furthermore, the scaffolds possessed a well-interconnected porous structure and exhibited an ability to support cell adhesion and proliferation.
| S-EPMC5502980 | biostudies-other
Project description:CaO-P2O5-SiO2-B2O3-ZnO bioactive glasses were prepared via an optimized sol-gel method. The current investigation was focused on producing novel zinc based calcium phosphoborosilicate glasses and to evaluate their mechanical, rheological, and biocompatible properties. The morphology and composition of these glasses were studied using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The particle size, mechanical and flexural strength was also determined. Furthermore, the zeta potential of all the glasses were determined to estimate their flocculation tendency. The thermal analysis and weight loss measurements were carried out using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) respectively. For assessing the in-vitro bioactive character of synthesized glasses, the ability for apatite formation on their surface upon their immersion in simulated body fluid (SBF) was checked using SEM and pH measurements. MTS assay cytotoxicity assay and live-dead cell viability test were conducted on J774A.1 cells murine macrophage cells for different glass concentrations.
| S-EPMC3957134 | biostudies-other
Project description:In the field of bone regeneration, considerable attention has been addressed towards the use of mesoporous bioactive glasses (MBGs), as multifunctional therapeutic platforms for advanced medical devices. In fact, their extremely high exposed surface area and pore volume allow to load and the release of several drugs, while their framework can be enriched with specific therapeutic ions allowing to boost the tissue regeneration. However, due to the open and easily accessible mesopore structure of MBG, the release of the incorporated therapeutic molecules shows an initial burst effect leading to unsuitable release kinetics. Hence, a still open challenge in the design of drug delivery systems based on MBGs is the control of their release behavior. In this work, Layer-by-layer (LbL) deposition of polyelectrolyte multi-layers was exploited as a powerful and versatile technique for coating the surface of Cu-substituted MBG nanoparticles with innovative multifunctional drug delivery systems for co-releasing of therapeutic copper ions (exerting pro-angiogenic and anti-bacterial effects) and an anti-inflammatory drug (ibuprofen). Two different routes were investigated: in the first strategy, chitosan and alginate were assembled by forming the multi-layered surface, and, successively, ibuprofen was loaded by incipient wetness impregnation, while in the second approach, alginate was replaced by ibuprofen, introduced as polyelectrolyte layer. Zeta-potential, TGA and FT-IR spectroscopy were measured after the addition of each polyelectrolyte layer, confirming the occurrence of the stepwise deposition. In addition, the in vitro bioactivity and the ability to modulate the release of the cargo were evaluated. The polyelectrolyte coated-MBGs were proved to retain the peculiar ability to induce hydroxyapatite formation after 7 days of soaking in Simulated Body Fluid. Both copper ions and ibuprofen were co-released over time, showing a sustained release profile up to 14 days and 24 h, respectively, with a significantly lower burst release compared to the bare MBG particles.
| S-EPMC8625996 | biostudies-literature
Project description:Recently, spark plasma sintering (SPS) has become an attractive method for the preparation of solid-state ceramics. As SPS is a pressure-assisted low-temperature process, it is important to examine the effects of temperature and pressure on the structural properties of the prepared samples. In the present study, we examined the correlation between the preparation conditions and the physical and structural properties of SiO2 glasses prepared by SPS. Compared with the conventional SiO2 glass, the SPS-SiO2 glasses exhibit a higher density and elastic modulus, but a lower-height first sharp diffraction peak of the X-ray total structure factor. Micro-Raman and micro-IR spectra suggest the formation of heterogeneous regions at the interface between the SiO2 powders and graphite die. Considering the defect formation observed in optical absorption spectra, reduction reaction mainly affects the densification of SPS-SiO2 glass. Hence, the reaction at the interface is important for tailoring the structure and physical properties of solid-state materials prepared by the SPS technique.
| S-EPMC9427799 | biostudies-literature
Project description:Considering the increase in patients who suffer from osteoporosis and the bone defects that occur in these patients, bone tissue regeneration is a promising option to solve this problem. To achieve a synergistic effect between the synthesis of a proper structure and bioactive/pharmaceutical activity, ions with a physiological effect can be added to silica structures, such as Ca2+, thanks to its bioactive behavior, and Ga3+ for its antibacterial and anticancer action. In this work, the synthesis of large pore mesoporous silica (LPMS), potential bioactive glasses containing Ca2+ and Ga3+, has been studied. Corresponding structures, in terms of composition, have been synthesized following the Sol-Gel EISA (Evaporation Induced Self-Assembly) process (obtaining Classical Mesoporous Silica, MS). Pore structure characterization of LPMSs and MSs has been performed using N2 adsorption/desorption and Hg-porosimetry, showing the presence of pores for LPMSs in the range of 20-60 and 200-600 nm. Nisin, a polycyclic antibacterial peptide, has been used for load tests. The load and release tests performed highlight a higher loading and releasing, doubled for LPMSs if compared to MSs. To confirm the maintenance of the structure of LPMSs and their mechanical strength and resistance, scanning electron microscopy images were acquired before and after release tests. Ca and Ga release in SBF has been studied through inductively coupled plasma-optical emission spectroscopy (ICP-OES), showing a particularly high release of these ions performed with LPMSs. The bioactive behavior of Ca-containing structures has been confirmed using FT-IR (Fourier-transform infrared spectroscopy), SEM-EDS (Scanning Electron Microscope-Energy Dispersive Spectroscopy), and X-ray powder diffraction (XRDP). In conclusion, LPMSs showed better loading and releasing properties compared with classical MS and better release in terms of active ions. In addition, it has also been demonstrated that LPMSs have bioactive behavior (a well-known characteristic of MSs).
| S-EPMC10820009 | biostudies-literature
Project description:Clinoptilolite as a natural zeolite was integrated with green CaO nanoparticles forming the green nanocomposite CaO(NP)/Clino. The CaO(NP)/Clino composite was assessed as a potential carrier for 5-fluorouracil (5-FL) drug. The CaO(NP)/Clino carrier achieved an enhanced 5-FL loading capacity of 305.3 mg/g as compared to 163 mg/g for pure clinoptilolite. The kinetics of the 5-FL loading follow the properties of the pseudo-first-order model, while the equilibrium results are related to the Langmuir isotherm. Therefore, the 5-FL loading processes occurred in the monolayer formed by homogeneous active loading receptors on the surface of the CaO(NP)/Clino carrier. The Gaussian energy of the 5-FL loading reaction (9.2 KJ/mol) reflected the dominant effect for the chemical mechanisms, especially the zeolitic ion-exchange mechanisms. Additionally, the thermodynamic parameters suggested endothermic, feasible, and spontaneous properties for the occurred 5-FL loading reactions. The release profile of 5-FL from CaO(NP)/Clino has continuous and long properties (150 h) at pH 1.2 (gastric fluid) and pH 7.4 (intestinal fluid). The kinetic studies of the release reactions show considerable agreement with Higuchi, Hixson-Crowell, and Korsmeyer-Peppas models. Such high fitting results and the diffusion exponent values (0.49 at pH 1.2 and 0.48 at pH 7.4) reflected the release properties of the Fickian transport behavior involving complex erosion and diffusion mechanisms. The cytotoxicity study of CaO(NP)/Clino on colorectal normal cells (CCD-18Co) declare the safe and biocompatible effect as a carrier for the 5-FL drug. Additionally, CaO(NP)/Clino as a carrier causes considerable enhancement for the cytotoxic effect of the loaded 5-FL drug on colon cancer cells (HCT-116).
| S-EPMC8637967 | biostudies-literature
Project description:Currently, the treatment of wounds is still a challenge for healthcare professionals due to high complication incidences and social impacts, and the development of biocompatible and efficient medicines remains a goal. In this regard, mesoporous materials loaded with bioactive compounds from natural extracts have a high potential for wound treatment due to their nontoxicity, high loading capacity and slow drug release. MCM-41-type mesoporous material was synthesized by using sodium trisilicate as a silica source at room temperature and normal pressure. The synthesized mesoporous silica was characterized by using Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), N2 absorption-desorption (BET), Dynamic Light Scattering (DLS) and Fourier transform infrared spectroscopy (FT-IR), revealing a high surface area (BET, 1244 m2/g); pore diameter of approx. 2 nm; and a homogenous, ordered and hexagonal geometry (TEM images). Qualitative monitoring of the desorption degree of the Salvia officinalis (SO) extract, rich in ursolic acid and oleanolic acid, and Calendula officinalis (CO) extract, rich in polyphenols and flavones, was performed via the continuous recording of the UV-VIS spectra at predetermined intervals. The active ingredients in the new composite MCM-41/sage and marigold (MCM-41/SO&CO) were quantified by using HPLC-DAD and LC-MS-MS techniques. The evaluation of the biological composites' activity on the wound site was performed on two cell lines, HS27 and HaCaT, naturally involved in tissue-regeneration processes. The experimental results revealed the ability to stimulate collagen biosynthesis, the enzymatic activity of the main metalloproteinases (MMP-2 and MMP-9) involved in tissue remodeling processes and the migration rate in the wound site, thus providing insights into the re-epithelializing properties of mesoporous composites.
| S-EPMC10534662 | biostudies-literature
Project description:Yb3+-doped phosphate glasses containing different amounts of SiO₂ were successfully synthesized by the conventional melt-quenching method. The influence mechanism of SiO₂ on the structural and spectroscopic properties was investigated systematically using the micro-Raman technique. It was worth noting that the glass with 26.7 mol % SiO₂ possessed the longest fluorescence lifetime (1.51 ms), the highest gain coefficient (1.10 ms·pm²), the maximum Stark splitting manifold of ²F7/2 level (781 cm-1), and the largest scalar crystal-field NJ and Yb3+ asymmetry degree. Micro-Raman spectra revealed that introducing SiO₂ promoted the formation of P=O linkages, but broke the P=O linkages when the SiO₂ content was greater than 26.7 mol %. Based on the previous 29Si MAS NMR experimental results, these findings further demonstrated that the formation of [SiO₆] may significantly affect the formation of P=O linkages, and thus influences the spectroscopic properties of the glass. These results indicate that phosphosilicate glasses may have potential applications as a Yb3+-doped gain medium for solid-state lasers and optical fiber amplifiers.
| S-EPMC5503361 | biostudies-other
Project description:C-A-S-H (CaO-Al₂O₃-SiO₂-H₂O) and N-A-S-H (Na₂O-Al₂O₃-SiO₂-H₂O) have a wide range of chemical compositions and structures and are difficult to separate from alkali-activated materials. Therefore, it is difficult to analyze their microscopic properties directly. This paper reports research on the synthesis of C-A-S-H and N-A-S-H particles with an average particle size smaller than 300 nm by applying the hydrothermal method. The composition and microstructure of the products with different CaO(Na₂O)/SiO₂ ratios and curing conditions were characterized using XRD, the RIR method, FTIR, SEM, TEM, and laser particle size analysis. The results showed that the C-A-S-H system products with a low CaO/SiO₂ ratio were mainly amorphous C-A-S-H gels. With an increase in the CaO/SiO₂ ratio, an excess of Ca(OH)₂ was observed at room temperature, while in a high-temperature reaction system, katoite, C₄AcH11, and other crystallized products were observed. The katoite content was related to the curing temperature and the content of Ca(OH)₂ and it tended to form at a high-temperature and high-calcium environment, and an increase in the temperature renders the C-A-S-H gels more compact. The main products of the N-A-S-H system at room temperature were amorphous N-A-S-H gels and a small amount of sodalite. An increase in the curing temperature promoted the formation of the crystalline products faujasite and zeolite-P. The crystallization products consisted of only zeolite-P in the high-temperature N-A-S-H system and its content were stable above 70%. An increase in the Na₂O/SiO₂ ratio resulted in more non-bridging oxygen and the TO₄ was more isolated in the N-A-S-H structure. The composition and microstructure of the C-A-S-H and N-A-S-H system products synthesized by the hydrothermal method were closely related to the ratio of the raw materials and the curing conditions. The results of this study increase our understanding of the hydration products of alkali-activated materials.
| S-EPMC5551738 | biostudies-other