Effect of Annealing Temperature on the Water Contact Angle of PVD Hard Coatings.
Ontology highlight
ABSTRACT:
SUBMITTER: Yang YS
PROVIDER: S-EPMC5521310 | biostudies-other | 2013 Aug
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Forming gas annealing is a common process step used to improve the performance of devices based on transition-metal dichalcogenides (TMDs). Here, the impact of forming gas anneal is investigated for PtSe2-based devices. A range of annealing temperatures (150, 250, and 350 °C) were used both in inert (0/100% H2/N2) and forming gas (5/95% H2/N2) environments to separate the contribution of temperature and ambient. The samples are electrically characterized by circular transfer length method structures, from which contact resistance and sheet resistance are analyzed. Ti and Ni are used as metal contacts. Ti does not react with PtSe2 at any given annealing step. In contrast to this, Ni reacts with PtSe2, resulting in a contact alloy formation. The results are supported by a combination of X-ray photoelectron spectroscopy, Raman spectroscopy, energy-dispersive X-ray spectroscopy, and cross-sectional transmission electron microscopy. The work sheds light on the impact of forming gas annealing on TMD-metal interfaces, and on the TMD film itself, which could be of great interest to improve the contact resistance of TMD-based devices.
| S-EPMC6812109 | biostudies-literature
Project description:We present a simple and effective method to obtain refined control of the molecular structure of silk biomaterials through physical temperature-controlled water vapor annealing (TCWVA). The silk materials can be prepared with control of crystallinity, from a low content using conditions at 4 °C (? helix dominated silk I structure), to highest content of ?60% crystallinity at 100 °C (?-sheet dominated silk II structure). This new physical approach covers the range of structures previously reported to govern crystallization during the fabrication of silk materials, yet offers a simpler, green chemistry, approach with tight control of reproducibility. The transition kinetics, thermal, mechanical, and biodegradation properties of the silk films prepared at different temperatures were investigated and compared by Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), uniaxial tensile studies, and enzymatic degradation studies. The results revealed that this new physical processing method accurately controls structure, in turn providing control of mechanical properties, thermal stability, enzyme degradation rate, and human mesenchymal stem cell interactions. The mechanistic basis for the control is through the temperature-controlled regulation of water vapor to control crystallization. Control of silk structure via TCWVA represents a significant improvement in the fabrication of silk-based biomaterials, where control of structure-property relationships is key to regulating material properties. This new approach to control crystallization also provides an entirely new green approach, avoiding common methods that use organic solvents (methanol, ethanol) or organic acids. The method described here for silk proteins would also be universal for many other structural proteins (and likely other biopolymers), where water controls chain interactions related to material properties.
| S-EPMC3090511 | biostudies-literature
Project description:Silicon is a widely applied material and the wetting of silicon surface is an important phenomenon. However, contradictions in the literature appear considering the value of the water contact angle (WCA). The purpose of this study is to present a holistic experimental and theoretical approach to the WCA determination. To do this, we checked the chemical composition of the silicon (1,0,0) surface by using the X-ray photoelectron spectroscopy (XPS) method, and next this surface was purified using different cleaning methods. As it was proved that airborne hydrocarbons change a solid wetting properties the WCA values were measured in hydrocarbons atmosphere. Next, molecular dynamics (MD) simulations were performed to determine the mechanism of wetting in this atmosphere and to propose the force field parameters for silica wetting simulation. It is concluded that the best method of surface cleaning is the solvent-reinforced de Gennes method, and the WCA value of silicon covered by SiO2 layer is equal to 20.7° (at room temperature). MD simulation results show that the mechanism of pure silicon wetting is similar to that reported for graphene, and the mechanism of silicon covered by SiO2 layer wetting is similar to this observed recently for a MOF.
| S-EPMC7177545 | biostudies-literature
Project description:Zinc oxide (ZnO) offers a great potential in several applications from sensors to Photovoltaic cells thanks to the material's dependency, to its optical and electrical properties and crystalline structure architypes. Typically, ZnO powder tends to be grown in the form of a wurtzite structure allowing versatility in the phase of material growths; albeit, whereas in this work we introduce an alternative in scalable yet relatively simple 2D hexagonal planed ZnO nanoflakes via the electrochemical deposition of commercially purchased Zn(NO?)? and KCl salts in an electrochemical process. The resulting grown materials were analyzed and characterized via a series of techniques prior to thermal annealing to increase the grain size and improve the crystal quality. Through observation via scanning electron microscope (SEM) images, we have analyzed the statistics of the grown flakes' hexagonal plane's size showing a non-monotonal strong dependency of the average flake's hexagonal flakes' on the annealing temperature, whereas at 300 °C annealing temperature, average flake size was found to be in the order of 300 ?m². The flakes were further analyzed via transmission electron microscopy (TEM) to confirm its hexagonal planes and spectroscopy techniques, such as Raman Spectroscopy and photo luminescence were applied to analyze and confirm the ZnO crystal signatures. The grown materials also underwent further characterization to gain insights on the material, electrical, and optical properties and, hence, verify the quality of the material for Photovoltaic cells' electron collection layer application. The role of KCl in aiding the growth of the less preferable (0001) ZnO is also investigated via various prospects discussed in our work. Our method offers a relatively simple and mass-producible method for synthesizing a high quality 2D form of ZnO that is, otherwise, technically difficult to grow or control.
| S-EPMC6120048 | biostudies-literature
Project description:TiO₂-SiO₂ binary coatings were deposited by a sol-gel dip-coating method using tetrabutyl titanate and tetraethyl orthosilicate as precursors. The structure and chemical composition of the coatings annealed at different temperatures were analyzed by Raman spectroscopy and Fourier Transform Infrared (FTIR) spectroscopy. The refractive indices of the coatings were calculated from the measured transmittance and reflectance spectra. An increase in refractive index with the high temperature thermal annealing process was observed. The Raman and FTIR results indicate that the refractive index variation is due to changes in the removal of the organic component, phase separation and the crystal structure of the binary coatings.
| S-EPMC5452115 | biostudies-other
Project description:Discordant U-Pb data of zircon are commonly attributed to Pb loss from domains with variable degree of radiation damage that resulted from α-decay of U and Th, which often complicates the correct age interpretation of the sample. Here we present U-Pb zircon data from 23 samples of ca. 1.7-1.9 Ga granitoid rocks in and around the Siljan impact structure in central Sweden. Our results show that zircon from rocks within the structure that form an uplifted central plateau lost significantly less radiogenic Pb compared to zircon grains in rocks outside the plateau. We hypothesize that zircon in rocks within the central plateau remained crystalline through continuous annealing of crystal structure damages induced from decay of U and Th until uplifted to the surface by the impact event ca. 380 Ma ago. In contrast, zircon grains distal to the impact have accumulated radiation damage at shallow and cool conditions since at least 1.26 Ga, making them vulnerable to fluid-induced Pb-loss. Our data are consistent with studies on alpha recoil and fission tracks, showing that annealing in zircon occurs at temperatures as low as 200-250 °C. Zircon grains from these samples are texturally simple, i.e., neither xenocrysts nor metamorphic overgrowths have been observed. Therefore, the lower intercepts obtained from regression of variably discordant zircon data are more likely recording the age of fluid-assisted Pb-loss from radiation-damaged zircon at shallow levels rather than linked to regional magmatic or tectonic events.
| S-EPMC8007740 | biostudies-literature
Project description:Water immersion insertion has been documented to decrease procedure-related discomfort during colonoscopy. There was used warm water infusion for colonoscope insertion in most of the water immersion colonoscopy trials.
The investigators have been using room temperature water (20-24°C) for water immersion and the investigators did not notice any drawback of it. In our opinion, it is simpler and cheaper option for water immersion colonoscopy and proof of its efficacy and safety could support the use of water immersion technique in routine practice.
The primary endpoint is cecal intubation time and the investigators suppose that the use of warm water infusion does not shorten it significantly. Patient comfort during colonoscope insertion, water consumption, length of the scope while reaching the cecum, need for external compression, need for positioning of the patient and endoscopist´s difficulty with colonoscopy will be also assessed.
| 2124104 | ecrin-mdr-crc
Project description:Electroplated hard chrome coating is widely used as a wear resistant coating to prolong the life of mechanical components. However, the electroplating process generates hexavalent chromium ion which is known carcinogen. Hence, there is a major effort throughout the electroplating industry to replace hard chrome coating. Composite coating has been identified as suitable materials for replacement of hard chrome coating, while deposition coating prepared using traditional co-deposition techniques have relatively low particles content, but the content of particles incorporated into a coating may fundamentally affect its properties. In the present work, Ni-W/diamond composite coatings were prepared by sediment co-electrodeposition from Ni-W plating bath, containing suspended diamond particles. This study indicates that higher diamond contents could be successfully co-deposited and uniformly distributed in the Ni-W alloy matrix. The maximum hardness of Ni-W/diamond composite coatings is found to be 2249 ± 23 Hv due to the highest diamond content of 64 wt.%. The hardness could be further enhanced up to 2647 ± 25 Hv with heat treatment at 873 K for 1 h in Ar gas, which is comparable to hard chrome coatings. Moreover, the addition of diamond particles could significantly enhance the wear resistance of the coatings.
| S-EPMC4770281 | biostudies-other
Project description:The combination of ceramic hardness with high crack resistance is a major challenge in the design of protective thin films. High entropy alloys have shown in earlier studies promising mechanical properties with a potential use as thin film materials. In this study, we show that small amounts of carbon in magnetron-sputtered multicomponent CrNbTaTiW films can lead to a significant increase in hardness. The film properties were strongly dependent on the metal composition and the most promising results were observed for TaW-rich films. They crystallised in a bcc structure with a strong (110) texture and coherent grain boundaries. It was possible to deposit films with 8?at.% C in a supersaturated solid-solution into the bcc structure without carbide formation. A major effect of carbon was a significant grain refinement, reducing the column diameter from approximately 35 to 10?nm. This resulted in an increase in hardness from 14.7 to 19.1?GPa while the reduced E-modulus stayed constant at 322?GPa. The carbon-containing films exhibited extremely little plastic deformation around the indent and no cracks were observed. These results show that supersaturation of carbon into high entropy films can be a promising concept to combine superior hardness with high crack resistance.
| S-EPMC6162281 | biostudies-other
Project description:The extensible byssal threads of marine mussels are shielded from abrasion in wave-swept habitats by an outer cuticle that is largely proteinaceous and approximately fivefold harder than the thread core. Threads from several species exhibit granular cuticles containing a protein that is rich in the catecholic amino acid 3,4-dihydroxyphenylalanine (dopa) as well as inorganic ions, notably Fe3+. Granular cuticles exhibit a remarkable combination of high hardness and high extensibility. We explored byssus cuticle chemistry by means of in situ resonance Raman spectroscopy and demonstrated that the cuticle is a polymeric scaffold stabilized by catecholato-iron chelate complexes having an unusual clustered distribution. Consistent with byssal cuticle chemistry and mechanics, we present a model in which dense cross-linking in the granules provides hardness, whereas the less cross-linked matrix provides extensibility.
| S-EPMC3087814 | biostudies-literature