Dataset Information

Experimental Investigation of Air Compliance Effect on Measurement of Mechanical Properties of Blood Sample Flowing in Microfluidic Channels.

ABSTRACT: Air compliance has been used effectively to stabilize fluidic instability resulting from a syringe pump. It has also been employed to measure blood viscosity under constant shearing flows. However, due to a longer time delay, it is difficult to quantify the aggregation of red blood cells (RBCs) or blood viscoelasticity. To quantify the mechanical properties of blood samples (blood viscosity, RBC aggregation, and viscoelasticity) effectively, it is necessary to quantify contributions of air compliance to dynamic blood flows in microfluidic channels. In this study, the effect of air compliance on measurement of blood mechanical properties was experimentally quantified with respect to the air cavity in two driving syringes. Under periodic on-off blood flows, three mechanical properties of blood samples were sequentially obtained by quantifying microscopic image intensity () and interface (?) in a co-flowing channel. Based on a differential equation derived with a fluid circuit model, the time constant was obtained by analyzing the temporal variations of ? = 1/(1-?). According to experimental results, the time constant significantly decreased by securing the air cavity in a reference fluid syringe (~0.1 mL). However, the time constant increased substantially by securing the air cavity in a blood sample syringe (~0.1 mL). Given that the air cavity in the blood sample syringe significantly contributed to delaying transient behaviors of blood flows, it hindered the quantification of RBC aggregation and blood viscoelasticity. In addition, it was impossible to obtain the viscosity and time constant when the blood flow rate was not available. Thus, to measure the three aforementioned mechanical properties of blood samples effectively, the air cavity in the blood sample syringe must be minimized (Vair, R = 0). Concerning the air cavity in the reference fluid syringe, it must be sufficiently secured about Vair, R = 0.1 mL for regulating fluidic instability because it does not affect dynamic blood flows.

SUBMITTER: Kang YJ

PROVIDER: S-EPMC7281095 | biostudies-literature | 2020 Apr

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Experimental Investigation of Air Compliance Effect on Measurement of Mechanical Properties of Blood Sample Flowing in Microfluidic Channels.

Kang Yang Jun YJ

Micromachines 20200428 5

Air compliance has been used effectively to stabilize fluidic instability resulting from a syringe pump. It has also been employed to measure blood viscosity under constant shearing flows. However, due to a longer time delay, it is difficult to quantify the aggregation of red blood cells (RBCs) or blood viscoelasticity. To quantify the mechanical properties of blood samples (blood viscosity, RBC aggregation, and viscoelasticity) effectively, it is necessary to quantify contributions of air compl ...[more]

PMID: 32354105

Similar Datasets

Project description:During the multistep process of metastasis, cancer cells encounter various mechanical forces which make them deform drastically. Developing accurate in-silico models, capable of simulating the interactions between the mechanical forces and highly deformable cancer cells, can pave the way for the development of novel diagnostic and predictive methods for metastatic progression. Spring-network models of cancer cell, empowered by our recently proposed identification approach, promises a versatile numerical tool for developing experimentally validated models that can simulate complex interactions at cellular scale. Using this numerical tool, we presented spring-network models of breast cancer cells that can accurately replicate the experimental data of deformation behavior of the cells flowing in a fluidic domain and passing narrow constrictions comparable to microcapillary. First, using high-speed imaging, we experimentally studied the deformability of breast cancer cell lines with varying metastatic potential (MCF-7 (less invasive), SKBR-3 (medium-high invasive), and MDA-MB-231 (highly invasive)) in terms of their entry time to a constricted microfluidic channel. We observed that MDA-MB-231, that has the highest metastatic potential, is the most deformable cell among the three. Then, by focusing on this cell line, experimental measurements were expanded to two more constricted microchannel dimensions. The experimental deformability data in three constricted microchannel sizes for various cell sizes, enabled accurate identification of the unknown parameters of the spring-network model of the breast cancer cell line (MDA-MB-231). Our results show that the identified parameters depend on the cell size, suggesting the need for a systematic procedure for identifying the size-dependent parameters of spring-network models of cells. As the numerical results show, the presented cell models can simulate the entry process of the cell into constricted channels with very good agreements with the measured experimental data.

Project description:Biomechanical and morphological analysis of the cells is a novel approach for monitoring the environmental features, drugs, and toxic compounds' effects on cells. Graphene oxide (GO) has a broad range of medical applications such as tissue engineering and drug delivery. However, the effects of GO nanosheets on biological systems have not been completely understood. In this study, we focused on the biophysical characteristics of cells and their changes resulting from the effect of GO nanosheets. The biophysical properties of the cell population were characterized as follows: cell stiffness was calculated by atomic force microscopy, cell motility and invasive properties were characterized in the microfluidic chip in which the cells are able to visualize cell migration at a single-cell level. Intracellular actin was stained to establish a quantitative picture of the intracellular cytoskeleton. In addition, to understand the molecular interaction of GO nanosheets and actin filaments, coarse-grained (CG) molecular dynamics (MD) simulations were carried out. Our results showed that GO nanosheets can reduce cell stiffness in MCF7 cells and MDA-MB-231 cell lines and highly inhibited cell migration (39.2%) in MCF-7 and (38.6%) in MDA-MB-231 cell lines through the GO nanosheets-mediated disruption of the intracellular cytoskeleton. In the presence of GO nanosheets, the cell migration of both cell lines, as well as the cell stiffness, significantly decreased. Moreover, after GO nanosheets treatment, the cell actin network dramatically changed. The experimental and theoretical approaches established a quantitative picture of changes in these networks. Our results showed the reduction of the order parameter in actin filaments was 23% in the MCF7 cell line and 20.4% in the MDA-MB-231 cell line. The theoretical studies also showed that the GO nanosheet-actin filaments have stable interaction during MD simulation. Moreover, the 2D free energy plot indicated the GO nanosheet can induce conformational changes in actin filaments. Our findings showed that the GO nanosheets can increase the distance of actin-actin subunits from 3.22 to 3.5 nm and in addition disrupt native contacts between two subunits which lead to separate actin subunits from each other in actin filaments. In this study, the biomechanical characteristics were used to explain the effect of GO nanosheets on cells which presents a novel view of how GO nanosheets can affect the biological properties of cells without cell death. These findings have the potential to be applied in different biomedical applications.

Dataset Information

Experimental Investigation of Air Compliance Effect on Measurement of Mechanical Properties of Blood Sample Flowing in Microfluidic Channels.

Publications

Experimental Investigation of Air Compliance Effect on Measurement of Mechanical Properties of Blood Sample Flowing in Microfluidic Channels.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets