Dataset Information

Surface Composition and Aerosolization Stability of an Inhalable Combinational Powder Formulation Spray Dried Using a Three-Fluid Nozzle.

ABSTRACT:

Purpose

This study aims to understand the impact of spray drying nozzles on particle surface composition and aerosol stability.

Methods

The combination formulations of colistin and azithromycin were formulated by 2-fluid nozzle (2 N) or 3-fluid (3 N) spray drying in a molar ratio of 1:1. A 3-factor, 2-level (2³) factorial design was selected to investigate effects of flow rate, inlet temperature and feed concentration on yield of spray drying and the performance of the spray dried formulations for the 3 N.

Results

FPF values for the 2 N formulation (72.9 ± 1.9% for azithromycin & 73.4 ± 0.8% for colistin) were higher than those for the 3 N formulation (56.5 ± 3.8% for azithromycin & 55.1 ± 1.6% for colistin) when stored at 20% RH for 1 day, which could be attributed to smaller physical size for the 2 N. There was no change in FPF for both drugs in the 2 N formulation after storage at 75% RH for 90 days; however, there was a slight increase in FPF for colistin in the 3 N formulation at the same storage conditions. Surface enrichment of hydrophobic azithromycin was measured by X-ray photoelectron spectroscopy for both 2 N and 3 N formulations and interactions were studied using FTIR.

Conclusions

The 3-fluid nozzle provides flexibility in choosing different solvents and has the capability to spray dry at higher feed solid concentrations. This study highlights the impact of hydrophobic azithromycin enrichment on particle surface irrespective of the nozzle type, on the prevention of moisture-induced deterioration of FPF for hygroscopic colistin.

SUBMITTER: Shetty N

PROVIDER: S-EPMC7647382 | biostudies-literature | 2020 Oct

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Surface Composition and Aerosolization Stability of an Inhalable Combinational Powder Formulation Spray Dried Using a Three-Fluid Nozzle.

Shetty Nivedita N Zhang Yiwen Y Park Heejun H Zemlyanov Dmitry D Shah Dishan D He Athena A Ahn Patricia P Mutukuri Tarun Tejasvi TT Chan Hak-Kim HK Zhou Qi Tony QT

Pharmaceutical research 20201009 11

<h4>Purpose</h4>This study aims to understand the impact of spray drying nozzles on particle surface composition and aerosol stability.<h4>Methods</h4>The combination formulations of colistin and azithromycin were formulated by 2-fluid nozzle (2 N) or 3-fluid (3 N) spray drying in a molar ratio of 1:1. A 3-factor, 2-level (2<sup>3</sup>) factorial design was selected to investigate effects of flow rate, inlet temperature and feed concentration on yield of spray drying and the performance of the ...[more]

PMID: 33037471

Similar Datasets

Project description:Soluplus is a polymer that has been explored to prepare nanocomposites for pulmonary drug delivery and is non-toxic. However, its aerosolization attributes when spray-dried have not been investigated. Hence, this work aimed to investigate the aerosol performance of soluplus-based spray-dried powders. In addition, the potential use of leucine to improve the aerosolization of such particles was also investigated by including leucine at 10 or 20% w/w. 4% w/w salbutamol was used as a model drug in all the formulations primarily to aid quantification during aerosolization evaluation and for assessing the interaction between the drug and soluplus using infrared spectroscopy with the multivariate analysis approach of principal component analysis (PCA). Three formulations (4% salbutamol/96% soluplus, 4% salbutamol/86% soluplus/10% leucine, 4% salbutamol/76% soluplus/20% leucine) were prepared. The formulations were characterized in terms of solid-state, water content, particle size/morphology, and aerosolization. Similarly, two additional formulations (14% salbutamol/86% soluplus and 24% salbutamol/76% soluplus) were prepared to assess potential non-covalent interactions between salbutamol and soluplus. The formulations with only salbutamol and soluplus were amorphous, as evident from X-ray diffraction. Leucine was crystalline in the formulations. All the spray-dried formulations were irregular spheres with surface corrugation. The 96% soluplus powder showed an emitted fraction (EF) and fine particles fraction (FPF) of 91.9 and 49.8%, respectively. The inclusion of leucine at 10% did not increase the EF; however, an increase in FPF (69.7%) was achieved with 20% leucine. PCA of the infrared spectra suggested potential non-covalent interactions between salbutamol and soluplus. It hinted at the potential involvement of ketone groups of the excipient. This study concludes that soluplus-based spray-dried powder with or without leucine can potentially be utilized for pulmonary drug delivery. In addition, PCA can effectively be utilized in assessing interactions and overcoming limitations associated with visual assessment of the spectra of such formulations.

Project description:In a spray drying operation, a two-fluid nozzle (2FN) with a single channel is commonly used for atomizing the feed solution. However, the less commonly used three-fluid nozzle (3FN) has two separate channels, which allow spray drying of materials in two incompatible solution systems. Although amorphous solid dispersions (ASDs) prepared using a 3FN have been reported to deliver comparable drug dissolution performance relative to those prepared using a 2FN, few studies have systematically examined the effect of 3FN on the physical stability. Therefore, the goal of this work is to systematically study the physical stability of ASDs that are spray-dried using a 3FN compared to those prepared using the traditional 2FN. For the 2FN, a single solution of naproxen and polyvinylpyrrolidone (PVP) was prepared in a mixture of acetone and water at a 1:1 volume ratio because 2FN allows for only one solution inlet. For the 3FN, naproxen and PVP were dissolved individually in acetone and water, respectively, because 3FN allows simultaneous entry of two solutions. Upon storage of the formulated ASDs at different humidity levels (25%, 55% and 75% RH), naproxen crystallized more quickly from the 3FN ASDs as compared with the 2FN ASDs. 3FN ASDs crystallized after 5 days of storage at all conditions, whereas 2FN ASDs did not crystallize even at 55% RH for two months. This relatively higher crystallization tendency of 3FN ASDs was attributed to the inhomogeneity of drug and polymers as identified by the solid-state Nuclear Magnetic Resonance findings, specifically due to poor mixing of water- and acetone-based solutions at the 3FN nozzle. When only acetone was used as a solvent to prepare drug-polymer solutions for 3FN, the formulated ASD was found to be stable for >3 months of storage (at 75% RH), which suggests that instability of the 3FN ASD was due to the insufficient mixing of water and acetone solutions. This study provides insights into the effects of solvent and nozzle choices on the physical stability of spray-dried ASDs.

Project description:SARS-CoV-2, the causative agent of COVID-19, predominantly affects the respiratory tract. As a consequence, it seems intuitive to develop antiviral agents capable of targeting the virus right on its main anatomical site of replication. Ivermectin, a U.S. FDA-approved anti-parasitic drug, was originally shown to inhibit SARS-CoV-2 replication in vitro, albeit at relatively high concentrations, which is difficult to achieve in the lung. In this study, we tested the spray-drying conditions to develop an inhalable dry powder formulation that could ensure sufficient antiviral drug concentrations, which are difficult to achieve in the lungs based on the oral dosage used in clinical trials. Here, by using ivermectin as a proof-of-concept, we evaluated spray-drying conditions that could lead to the development of antivirals in an inhalable dry powder formulation, which could then be used to ensure sufficient drug concentrations in the lung. Thus, we used ivermectin in proof-of-principle experiments to evaluate our system, including physical characterization and in vitro aerosolization of prepared dry powder. The ivermectin dry powder was prepared with a mini spray-dryer (Buchi B-290), using a 23 factorial design and manipulating spray-drying conditions such as feed concentration (0.2% w/v and 0.8% w/v), inlet temperature (80 °C and 100 °C) and presence/absence of L-leucine (0% and 10%). The prepared dry powder was in the size range of 1-5 μm and amorphous in nature with wrinkle morphology. We observed a higher fine particle fraction (82.5 ± 1.4%) in high feed concentration (0.8% w/v), high inlet temperature (100 °C) and the presence of L-leucine (10% w/w). The stability study conducted for 28 days confirmed that the spray-dried powder was stable at 25 ± 2 °C/<15% RH and 25 ± 2 °C/ 53% RH. Interestingly, the ivermectin dry powder formulation inhibited SARS-CoV-2 replication in vitro with a potency similar to ivermectin solution (EC50 values of 15.8 µM and 14.1 µM, respectively), with a comparable cell toxicity profile in Calu-3 cells. In summary, we were able to manipulate the spray-drying conditions to develop an effective ivermectin inhalable dry powder. Ongoing studies based on this system will allow the development of novel formulations based on single or combinations of drugs that could be used to inhibit SARS-CoV-2 replication in the respiratory tract.

Dataset Information

Surface Composition and Aerosolization Stability of an Inhalable Combinational Powder Formulation Spray Dried Using a Three-Fluid Nozzle.

Purpose

Methods

Results

Conclusions

Publications

Surface Composition and Aerosolization Stability of an Inhalable Combinational Powder Formulation Spray Dried Using a Three-Fluid Nozzle.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets