Dataset Information

Prevention of Microsphere Blockage in Catheter Tubes Using Convex Air Bubbles.

ABSTRACT: This paper presents a novel method to prevent blockages by embolic microspheres in catheter channels by using convex air bubbles attached to the channels' inner wall surface. The clogging by microspheres can occur by the arching of the microspheres in the catheter. A few studies have been done on reducing the blockage, but their methods are not suitable for use with embolic catheters. In this study, straight catheter channels were fabricated. They had cavities to form convex air bubbles; additionally, a straight channel without the cavities was designed for comparison. Blockage was observed in the straight channel without the cavities, and the blockage arching angle was measured to be 70°, while no blockage occurred in the cavity channel with air bubbles, even at a geometrical arching angle of 85°. The convex air bubbles have an important role in preventing blockages by microspheres. The slip effect on the air bubble surface and the centrifugal effect make the microspheres drift away from the channel wall. It was observed that as the size of the cavity was increased, the drift distance became larger. Additionally, as more convex air bubbles were formed, the amount of early drift to the center increased. It will be advantageous to design a catheter with large cavities that have a small interval between them.

SUBMITTER: Park DH

PROVIDER: S-EPMC7760967 | biostudies-literature | 2020 Nov

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Prevention of Microsphere Blockage in Catheter Tubes Using Convex Air Bubbles.

Park Dong Hyeok DH Jung Yeun Jung YJ Steve Jeo Kins Sandoz John Kinson SJK Kim Young Deok YD Go Jeung Sang JS

Micromachines 20201127 12

This paper presents a novel method to prevent blockages by embolic microspheres in catheter channels by using convex air bubbles attached to the channels' inner wall surface. The clogging by microspheres can occur by the arching of the microspheres in the catheter. A few studies have been done on reducing the blockage, but their methods are not suitable for use with embolic catheters. In this study, straight catheter channels were fabricated. They had cavities to form convex air bubbles; additio ...[more]

PMID: 33260919

Similar Datasets

Project description:Background In perioperative care or intensive care units, the expansion lines of endotracheal tubes (ETTs) or laryngeal mask airways (LMAs) may be accidentally cut off during medical procedures. We designed a simple method for repairing damaged ETT and LMA expansion lines. Methods In this in vitro study, ETT (n = 20) or LMA (n = 20) models were each categorized into experimental (n = 10) and control (n = 10) groups. In the experimental groups, the expansion lines were cut in the middle, and a 22G intravenous catheter was inserted into the broken end of each expansion line. The time taken to repair the expansion lines was recorded in both experimental groups. The repaired expansion lines in both groups were tested for visible underwater air leakage with cuffs under high pressure (120 cm H2O). After 15 h, the cuff pressure and tensile strength of the expansion lines were measured. Results The overall time required to repair the expansion line was 27.8 ± 1.5 s in the ETT group and 20.4 ± 1.1 s in the LMA group. When the cuff pressure was increased to 120 cmH2O, no air leakage was observed in the experimental LMA and ETT groups. The mean difference in the cuff pressures of the control and experimental groups was insignificant for both, ETT (9.50 ± 1.29 vs. 9.50 ± 1.08 cmH2O, 95% CI = − 1.11 to 1.11 cmH2O, P = 1.00) and LMA (34.1 ± 1.10 cmH2O vs. 34.5 ± 0.97 cmH2O, 95% CI = − 0.57 to 1.37 cmH2O, P = 0.40) groups, The tensile strength and the force required to pull apart the expansion lines in the experimental groups were lower than those in the control groups for ETTs (3.32 ± 0.37 N vs. 35.03 ± 4.47 N, 95% CI = − 34.69 to − 28.72 N, P < 0.0001) and LMAs (36.55 ± 2.20 N vs. 26.18 ± 1.67 N, 95% CI = − 12.21 to − 8.53 N, P < 0.0001). Conclusion An intravenous catheter can be directly inserted into the damaged ETT or LMA expansion lines; it is a simple, rapid, and effective repair method. Supplementary Information The online version contains supplementary material available at 10.1186/s12871-022-01776-5.

Dataset Information

Prevention of Microsphere Blockage in Catheter Tubes Using Convex Air Bubbles.

Publications

Prevention of Microsphere Blockage in Catheter Tubes Using Convex Air Bubbles.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets