Fracture strength analysis of titanium insert-reinforced zirconia abutments according to the axial height of the titanium insert with an internal connection.
Ontology highlight
ABSTRACT:
SUBMITTER: Song SR
PROVIDER: S-EPMC8016344 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:This study evaluates the dynamic shift in the microbiota at the peri-implant site of titanium (Ti) and zirconia (Zr) implants subjected to experimental peri-implantitis (PI) and, for the first time, of implants made of ceria-stabilized alumina-reinforced zirconia (Ce-TZP/Al), a revolutionary zirconia that is set to play a key role in modern implant dentistry. One- and two-piece (TP) implants, including Ce-TZP/AL TP/G3 glass, were placed bilaterally (six implants/side) in five beagle dogs to mimic a natural vs. ligature-induced PI following a split-mouth design. The experiment spanned 30 weeks from tooth extraction. Both PI models promoted plaque deposition at peri-implant sites. Comparatively, the PI induced by ligatures favored the deposition of anaerobes (p = 0.047 vs. natural). Regardless of the model, the plaque deposition pattern was entirely dependent on the implanted material. Ligated Ti and Zr implant sites accumulated up to 2.14 log CFU/mL unit anaerobic load (p ≤ 0.033 vs. non-ligated implant sites), predominantly comprising obligate anaerobes. Naturally occurring PI induced the deposition of co-occurring networks of obligate anaerobes and less oxygen-dependent bacteria. PI induction favored the enrichment of Ti and Zr sites with bacterial taxa belonging to the orange and red complexes (up to 28% increase naturally and up to 71% in the ligated hemiarch). Anaerobic deposition was significantly lower in ligated Ce-TZP/Al implant sites (p ≤ 0.014 vs. TI and Zr) and independent of the induction model (0.63-1 log units of increase). Facultative bacteria prevailed at Ce-TZP/AL sites. The abundance was lower in the Ce-TZP/AL TP implant. Unlike Ti and Zr sites, taxa from the orange and red complexes were negligible. Biofilms configured at the Ti and Zr sites after ligation-induced PI resemble those found in severe IP. We hypothesize that, although surface properties (surface energy and surface roughness) and physicochemical properties of the substrate play an important role in bacterial adhesion and subsequent plaque formation, Ce-TZP/Al modulates several biological activities that preserve the integrity of the gingival seal by limiting PI progression. In conclusion, biofilm progression differs in peri-implant sites according to the specific properties of the material. Ce-TZP/A, unlike titanium or zirconia, prevents dysbiosis in sites subjected to experimental PI and preserves the microbial signature of emergent obligate anaerobes related to PI development.
| S-EPMC11350813 | biostudies-literature
Project description:ObjectivesTo investigate survival rates, technical and biologic outcomes of buccally micro-veneered all-ceramic single implant crowns.Material and methodsSixty subjects randomly received immediately or early placed implants. Crowns out of lithium-disilicate (n = 30) and zirconia-ceramic (n = 30) were bonded to titanium-base-abutments. Restorations were inspected at baseline (BL) and during follow-up visits (6, 12 months). Technical and biologic parameters were recorded. Data were analysed descriptively. Differences between groups were tested with Student's t-test. Paired T-test was used when comparing data from the same implant or tooth over time. Linear model repeated measures were used to test differences between materials over time. Differences in counts were evaluated using Pearson Chi-square test. The level of significance was at p < .05.ResultsAfter a mean observation time of 13.2 ± 2.4 months, 54 restorations were re-examined. The implant survival rate was 98.3%, and the restoration survival rate was 100%. One early implant failure occurred. Two minor chippings occurred in lithium-disilicate restorations. No chippings or fractures occurred in any zirconia restorations at 1 year (0%). The technical complication rate was 3.7%, with 7.7% complications among the lithium-disilicate restorations and no differences between the two materials (p = .558). At 1-year follow-up, mean Bleeding on Probing (BOP) was higher at implants (0.27 ± 0.3) than adjacent teeth (0.17 ± 0.18) (p = .046) with no differences between materials (p = .36). Differences in pocket probing depth (PPD) between implants and adjacent teeth were significant (p < .01). Jemt Index improved significantly from BL to 1-y-follow-up (p < .001).ConclusionsPreliminary results were good, suggesting that the ceramic type does not impact technical and biologic parameters.
| S-EPMC10098475 | biostudies-literature
Project description:ObjectivesDental implant abutments are fundamental prosthetic components within dentistry that require optimal biocompatibility. The primary aim of this cross-sectional study was to preliminarily assess differences in the pro-inflammatory cytokine and bone metabolism mediator protein expression in the peri-implant crevicular fluid (PICF) adjacent to transmucosal abutments.Material and methodsAbutments were fabricated from either titanium or zirconia in patients previously receiving single-tooth implant therapy. All subjects sampled in this study had an identical implant system and implant-abutment connection. Participants (n = 46) had an average time of clinical function for 22 months (6.2-72.8 months, ±SD 17 months) and received a clinical and radiographic examination of the implant site at the time of PICF sampling using a paper strip-based sampling technique. Cytokine, chemokine, and bone metabolism mediator quantities (picograms/30 s) were determined using a commercial 22-multiplexed fluorescent bead-based immunoassay instrument. A total of 19 pro-inflammatory cytokines and seven bone metabolism mediators were evaluated.ResultsMultivariable analyses provided no evidence of a group (titanium or zirconia), gender, or age effect with regard to the expression of pro-inflammatory mediators evaluated. Significant (P = 0.022) differences were observed for the bone mediator leptin, with titanium abutments demonstrating significantly elevated levels in comparison with zirconia. Osteopontin demonstrated a significant (P = 0.0044) correlation with age of the subjects.ConclusionsNo significant differences in pro-inflammatory cytokine or bone metabolism mediator profiles were observed biochemically, with the exception of leptin, for the abutment biomaterials of titanium or zirconia The molecular PICF findings support the observed clinical biocompatibility of both titanium and zirconia abutments.
| S-EPMC4096610 | biostudies-literature
Project description:In recent years, Zirconia-reinforced Lithium Silicate ceramic (ZLS), combining lithium-silicate and zirconia features, has shown to have excellent mechanical and aesthetic characteristics. Thus, the aim of this study was to compare the fracture strength of ZLS single crowns cemented with two different cementation techniques. Twenty crowns were realised and cemented on teeth replicas achieved from an extracted premolar human tooth. The samples were divided into two groups of 10 specimens each, Glass-ionomeric cement (GIC) group and Self-Adhesive Resin Cement (ARC) group. The mechanical test was performed using a universal testing machine. The specimens were then evaluated with a scanning electron microscope (SEM) to identify for all crowns and related abutments the pattern of fracture after the breaking point. The data obtained were statistically analysed. The mean fracture toughness values and standard deviations (±SD) were 2227 ± 382 N and 3712 ± 319 N respectively for GIC and ARC groups. In fact, t-test showed a statistically significant difference between the two groups (p < 0.001). Moreover, the SEM results demonstrated portions of abutments still attached to the crown fragments in the ARC group, whilst these were not present in the GIC group. Within the limitations of this study, these results suggest the use of adhesive cementation for ZLS crowns, which significantly increase the compressive strength of ZLS restorations compared to GIC.
| S-EPMC7254201 | biostudies-literature
Project description:In this study, marginal and internal misfit and fracture load with and without thermal-mechanical aging (TMA) of monolithic ZLS and lithium disilicate (LDS) crowns were evaluated.Crowns were milled using a computer-aided design/computer-aided manufacturing system. Marginal gaps (MGs), absolute marginal discrepancy (AMD), axial gaps, and occlusal gaps were measured by X-ray microtomography (n=8). For fracture load testing, crowns were cemented in a universal abutment, and divided into four groups: ZLS without TMA, ZLS with TMA, LDS without TMA, and LDS with TMA (n=10). TMA groups were subjected to 10,000 thermal cycles (5-55°C) and 1,000,000 mechanical cycles (200 N, 3.8 Hz). All groups were subjected to compressive strength testing in a universal testing machine at a crosshead speed of 1 mm/min until failure. Student's t-test was used to examine misfit, two-way analysis of variance was used to analyze fracture load, and Pearson's correlation coefficients for misfit and fracture load were calculated (α=0.05). The materials were analyzed according to Weibull distribution, with 95% confidence intervals.Average MG (p<0.001) and AMD (p=0.003) values were greater in ZLS than in LDS crowns. TMA did not affect the fracture load of either material. However, fracture loads of ZLS crowns were lower than those of LDS crowns (p<0.001). Fracture load was moderately correlated with MG (r=-0.553) and AMD (r=-0.497). ZLS with TMA was least reliable, according to Weibull probability.Within the limitations of this study, ZLS crowns had lower fracture load values and greater marginal misfit than did LDS crowns, although these values were within acceptable limits.
| S-EPMC5482251 | biostudies-other
Project description:The purpose of this study was to evaluate the adherence of streptococci to disks of titanium (commercially pure titanium: CpTi) and zirconia (tetragonal zirconia polycrystals: TZP). CpTi and yttria-stabilized TZP disks with a mirror-polished surface were used as specimens. The arithmetic mean surface roughness (Ra and Sa) and the surface wettability of the experimental specimens were measured. For analyzing the outermost layer of the experimental specimens, X-ray photoelectron spectroscopy (XPS) analysis was performed. Streptococcus sanguinis, S. gordonii, S. oralis, and S. mutans were used as streptococcal bacterial strains. These bacterial cultures were grown for 24 h on CpTi and TZP. The number of bacterial adhesions was estimated using an ATP-bioluminescent assay, and scanning electron microscope (SEM) observation of the adhered bacterial specimens was performed. No significant differences in surface roughness or wettability were found between CpTi and TZP. In XPS analyses, outermost layer of CpTi included Ti0 and Ti4+, and outermost layer of TZP included Zr4+. In the cell adhesion assay, the adherences of S. sanguinis, S. gordonii, and S. oralis to TZP were significantly lower than those to CpTi (p < 0.05); however, significant difference was not observed for S. mutans among the specimens. The adherence to CpTi and TZP of S. mutans was significantly lower than that of S. sanguinis, S. gordonii, and S. oralis. These results were confirmed by SEM. S. sanguinis, S. gordonii, and S. oralis adhered less to TZP than to CpTi, but the adherence of S. mutans was similar to both surfaces. S. mutans was less adherent compare with the other streptococci tested in those specimens.
| S-EPMC7314031 | biostudies-literature
Project description:BACKGROUND:To assess the effects of differently sized titanium (Ti) and zirconia (Zr) particles on (1) the metabolic activity of osteosarcoma-derived osteoblasts (SaOs-2) and human gingival fibroblasts (HGF) and (2) the cytokine expression of monocytes (THP-1) METHODS: Ti (60-80?nm and 100?nm) and Zr (2??m and 75??m) particles were incubated with SaOs-2, HGF, and THP-1 cells. At days 0, 2, 4, and 7 and 0, 1, 2, and 4 (THP-1), the mitochondrial activity was assessed and enzyme-linked immunosorbent assays were used to determine interleukin (IL)-1 beta and IL-6 concentrations of stimulated THP-1 at day 1. RESULTS:Ti60-80, Ti100, Zr2, and Zr75 particles were associated with gradual and significant within-group decreases in the viability of SaOs-2 and HGF cells. These effects were less pronounced in the Zr group. Similar to control cells, THP-1 did not reveal any significant increases in IL-1 beta and IL-6 concentrations. Viability of THP-1 was merely impaired in the presence of Ti100. CONCLUSIONS:Ti and Zr particles had a detrimental effect on the viability of SaOs-2 and HGF, but no proinflammatory effect on THP-1.
| S-EPMC6614223 | biostudies-literature
Project description:The integrity of soft tissue seal is essential for preventing peri-implant infection, mainly induced by established bacterial biofilms around dental implants. Nowadays, graphene is well-known for its potential in biocompatibility and antisepsis. Herein, a new titanium biomaterial containing graphene (Ti-0.125G) was synthesized using the spark plasma sintering (SPS) technique. After material characteristics detection, the subsequent responses of human gingival fibroblasts (HGFs) and multiple oral pathogens (including Streptococci mutans, Fusobacterium nucleatum, and Porphyromonas gingivalis) to the graphene-reinforced sample were assessed, respectively. Also, the dynamic change of the bacterial multispecies volume in biofilms was evaluated using absolute quantification PCR combined with Illumina high-throughput sequencing. Ti-0.125G, in addition to its particularly pronounced inhibitory effect on Porphyromonas gingivalis at 96 h, was broadly effective against multiple pathogens rather than just one strain. The reinforced material's selective responses were also evaluated by a co-culture model involving HGFs and multiple strains. The results disclosed that the graphene-reinforced samples were highly effective in keeping a balance between the favorable fibroblast responses and the suppressive microbial growth, which could account for the optimal soft tissue seal in the oral cavity. Furthermore, the underlying mechanism regarding new material's bactericidal property in the current study has been elucidated as the electron transfer, which disturbed the bacterial respiratory chain and resulted in a decrease of microbial viability. According to the Kyoto Encyclopedia of Genes and Genomes (KEGG) database, the PICRUSt tool was conducted for the prediction of microbial metabolism functions. Consequently, it is inferred that Ti-0.125G has promising potentials for application in implant dentistry, especially in enhancing the integrity of soft tissue and improving its resistance against bacterial infections around oral implants.
| S-EPMC8076685 | biostudies-literature
Project description:ObjectiveVery few studies have investigated dental implant components involved in the early stage of healing, especially the implant healing abutment (IHA), despite its vital role in soft tissue contouring and shaping after implant placement. Although these components are labelled by the manufacturer for "single-use only," it is a common clinical practice to clean, sterilize, and reuse them.MethodsIn the present study, IHAs after single and multiple implantations were retrieved as per standard procedures, and biological material isolated from the surface was subjected to 16S rRNA sequence analysis. The microbiome analysis was followed by cleaning and sterilization in order to replicate clinical sterilization techniques. Following sterilization, retrievals were subjected to surface characterization with optical and scanning electron microscopy to investigate surface features, and electrochemical testing was performed to evaluate corrosion behavior.ResultsThe microbiota was comprised of early colonizers including Streptococcus species and secondary anaerobic colonizers such as Fusobacterium, Capnocytophaga, and Prevotella species. The surface analysis revealed that irrespective of the cleaning and sterilization techniques, the pristine, homogeneous surface of the new, unused IHAs could not be restored. Both single and multiple-use IHAs had severe surface changes including discoloration, major abrasions, biological contamination, and the IHA retrievals exhibited higher corrosion rate as compared to control specimens.SignificanceReusing IHAs multiple times may not be a prudent practice as the microbial colonization and surface changes caused by using this component multiple times may affect the performance of IHAs in soft tissue healing.
| S-EPMC7429256 | biostudies-literature
Project description:BACKGROUND:When implants are restored with cement-retained restorations, prosthetic retrievability can be difficult and often requires sectioning using rotary instruments. Sometimes repeated removals of a cement-retained implant crown are needed such as for treatment of peri-implantitis or immediate implant provisionalization. The purpose of this study was to evaluate the effect of erbium-doped yttrium aluminum garnet (Er:YAG) laser as a non-invasive treatment modality to remove lithium disilicate crowns from zirconia implant abutments following long-term cementation, repetitive debonding and re-cementation, and short-term retrieval. MATERIAL AND METHODS:Twenty identical lithium disilicate crowns were cemented onto zirconia prefabricated abutments using composite resin cement. Ten cemented crowns were removed at 48 hours after cementation as a short-term group (ST), while another 10 were removed 6 months after cementation as a long-term group (LT). To mimicking repetitive recementation and retrieval, the LT crowns were then recemented and removed after 48 hours as a long-term recemention (LTR) group. The LTR crowns were then again recemented and removed after 48 hours as a long-term repeated recemention (LTRR) group. Er:YAG laser was used to facilitate the retrieval of these crowns. recorded and analyzed using ANOVA and t-test. The surfaces of the crown and the abutment were further examined using light microscopy and scanning electron microscopy (SEM). Temperature changes of the abutment and crown upto 10 minutes were also measured and statistically analyzed (paired t-test). RESULTS:The average times of crown removal from zirconia abutments were 4 minutes (min) and 42 second (sec) in LT to 3 min 24 sec in LTR, and 3 min 12 sec in LTRR and ST groups. LTR took the longest time to remove, statistically (ANOVA and t-test, p < .001). No statistical differences were observed among the removal times of LTR, LTRR, and ST groups (t-test, p = .246, .246 and 1). SEM examination of the material surface showed no visual surface damaging from treatment with Er:YAG laser. The temperatures during irradiation ranged from 18.4°C to 20°C and 22.2°C to 24.5°C (Paired t-test, p < .0001) for the abutment and the crown during irradiation from 1 min to 10 mins. CONCLUSIONS:Long-term cementation can increase time in lithium disilicate crown removal from zirconia abutment using Er:YAG. Er:YAG laser is a non-invasive tool to remove cement-retained implant prostheses and should be considered as a viable alternative to rotary instruments.
| S-EPMC6830778 | biostudies-literature